I have a DAMOS (Audi A3 EDC17C74 04L906026BN v1197) and the same FR both in German and in English. Recently I updated my ECU to 04L906026BN v.7759 and I worked for days copying every single map at the right offset from the damos of the old version to a new project of the new version. The only problem is that I made on the test version of Winols 5 and it doesn't open on winols 4, now I need someone that export the mappack from a full version of winols 5 to reimport in the project of winols 4 so if you know someone with full version of winols 5 I will appreciate and also I can share to you that new demos made by me or the FR.
Hello.
Im looking for bdm read :
edc16u31 vw T5 2.5tdi
070997016M 2605 sw 1037394151
I cant reflash to ori with *sgo file on table ,so maybe someone will help.
BR
Yo guys,
I need to find and modify one canbus data in EGS52 TCU. I don't have knowledge is stored in Flash memory or not, but probably yes. Someone can help me?
I need to find canbus data with ID 418 and change to other ID.
Example flash file from EGS52 in attachment.
Which is the better choice?
I would mostly use it for unlocking sfd.
I have vcds but I think there will be no sfd unlock function in the near future unfortunetly.
hi, here a file of renault master III read on OBD by KESS v2 chinise clone, i wandring if this file correcte to inject it on the ECU or do i need to read it by KTag
you'll find é file original and DPF file
thank's in advance
I have problem with Peugeot 307 2002. BSI Valeo G0X-00 + ECU IAW 4MP2.01. Car not starting. ECU is blocked by BSI. BSI is paired with ECU. BSI not see key and not unblock ECU. Key is original, working (checked by external Autel key reader). I tried another virgin BSI - the same problem. I tried relearn key - operation not succesfull, message: problem with key learn.
I tried off immo in ECU (read 29f200bb and change 4000-7FFF to FF) not working - ECU still blocked ( F3 in plug B is empty, no cable).
I have a Skoda Octavia 5E 2019 1,5 tsi in my workshop.
It is from a fleet, and all the immo parts (engine ecu, dash, and keys) are removed to another car, so the original ones are not available.
The Skoda dealer solution is i have to buy everything new, but i would like to do it with second hand units (engine ECU cluster), and a new lockset with two new original key.
The engine ecu is Bosch MG1CS011 05E907593 with software 05E906018AL
The cluster is 5e0920740f with RH850
If I buy used ones, how can i make it work?
I have official online ODIS wih Geko, but my problem is nothing of the immo system is in the car, and i think ODIS won't do the immo adaptation...
Hey friends, i buy audi a5 2010 2.0 D with multitronic gearbox problem, drive reverse , but not forward, diagnostic shows p1741 fault code, cluch pressure adaptation , adaptation limit reached , checked oil level, ewerything is ok, but oil smells like burn cluch friction , so i start searching a second hand gearbox , i found from a4 , but 2016 years cvt , so my question its the same boxes? Mine LLA , second hand NYM , second question is , how with cloning epprom from old to new ? Just clone software and write to new , and after that how to do proper adaptation ,with vcds ? Or not need do that after cloning? Or just change tcu from mine to second hand box?
IS IT POSSIBLE TO DO IMMO OFF ON THIS ECU? I HAVE GENERATED KEYS WITH VVDI 2, NO LUCK, CANNOT START THE BIKE AT ALL... I HAVE READ MPC AND EEPROM ALSO, CAN SOMEBODY HELP ME EITHER DO IMMO OFF OR GENERATE KEYS WITH ANOTHER TOOL? THANKS IN ADVANCE!
Hello. Can somebody help turn off dpf and egr on this car? Ecu denso RF8LEK000.HEX GF0BRF8LT1BA. Please don't send remower job it turn off all dtcs. Thanks.
