i'm searching where is immo box in this car? i need to disconnect it, i remove almost all dash but can't find it.
Maybe someone know where it's located?
Hi. Anyone can give directions were to get bmw IMIB HV MA software to install on ISTA tablet to establish communication between all Imib tester and tablet
Hello friends, i have a problem with airbag computer, tryed to erase datacrash with airbag tool v02, but after erase the computer does not comunicate anymore on the car.After programming with the original bin again, it comunicates.I have tryed with 2 computers, same result.Can someone help me with data crash erase please?
I am attaching the data fropm the 2 computers, the one with 02 at the end is the original.
Dobrý den, prosím potřebuji pomoc s omezovačem otáček na jednotce 047906030N 5WP4326
S kamarádem máme projekt felicia 1.3 turbo a snažíme se ladit na originální jednotce Simos 23P, kterou
jsem našel na internetu, že omezovač by měl být na adrese 0x100DF, ale po změně této adresy je omezovač stále na cca. 6100. Prosím o pomoc. jinak vozidlo na youtube RENDOLF69 1.3 Mpi TURBO
Děkuji moc.
Hello, please help, I have a FIAT BRAVA and I am dealing with battery discharge, using an ammeter it was measured that the battery is discharging EPS. when eps disconnect the power connector, the current is set to 12mA. when I disconnect the data connector and connect the power one, the steering starts even when the key is out of the vehicle. if I leave everything connected, the control turns on only after the CAN bus is put to sleep. and then the current consumption will increase to 2-3A. the problem is probably in the EPS unit because it starts every time the CAN stops. 15+ pin in the data conector works, otherwise the control shows no error. only when the vehicle is stopped does it start drawing current and the booster really boosts. Please, if anyone has an idea how to fix the steering (EPS unit). Thank you
I want to test MB NTG4.5 on bench. I know there is already a thread here but i'm not sure what components i need to run this HU on bench.
- EZS?
- Instrument panel?
- SAM?
...if anybody wants to share the "secret" about the crackling audio problem with me, PN please! i will pay for the solution, no problem and i don't share!
Hello,
I would like to deactivate the EGR and DPF on my OM642 engine. I have Xentry and DAS software. My OBD adapter is the OpenPort, which works very well. Which program can I use with this adapter to disable both of these features? Vediamo doesn’t allow it, or I don’t have the right file for my engine that communicates with the OpenPort.
Maybe there’s a simple program to easily modify the software using the OpenPort.
hello
i cloned mrg1 ecu using flex and new ecu didnt work in the car
anyone have any way to sort it out
i will post the original ecu read and the new ecu
Hello everyone! Chrysler 200 2015. Error B2204 body. ECU mismatch. How to return the body settings to default so that the mileage does not blink on the dashboard. As I understand it, the settings in the body do not match the car.
Who can reset the crash data for module 8W0959655F, part number 0285013643? The EEPROM is a 95128, and the dump file with all necessary details is attached.
Friends, I have such a problem. I am trying to add a card to BCM X95 nec v850 using vvdi2. VVdi2 reports an unknown version problem. File read with Vvdi prog. It says on the processor that it is D76F0115GM, I read it as PD703384, vvdi2 itself prompts me to do so. Unfortunately, VVdi2 reports an unknown version error. The support spreads its hands. Does anyone have a solution to the problem?
ZDOBD EPS001 Heavy Duty Truck Scanner for Android & IOS Portable Disel Truck OBD Diagnostic Instrument
Price: €95
The ZDOBD EPS001 Bluetooth Heavy Duty Truck Scanner can easily reset and regenerate your DPF on Cummins engines to keep them humming. Instead of shelling out a fortune at the shop for a forced regeneration, this heavy duty truck scanner can save you thousands a year! Keep your engine in the best state and extend your truck's lifespan.
Truck Diagnostics: With the ZDOBD EPS001 Bluetooth Heavy Duty Truck Scanner, you can read and clear fault codes. From engines to EBS, and beyond, you can tackle repairs like a pro. Supporting the latest ISO 27145 and classic protocols like SAE J1939, SAE J1708, SAE 27145, it's compatible with Class 4-8 trucks. Compact and user-friendly, this diesel diagnostic tool is here to save you time and frustration!
ZDOBD EPS001 Features:
DPF Regeneration: DPF code clearing/Reset
Support CUMMINS, VOLVO, SCANNIA, FREIGHTLINER
Supported Languages: English, Russian, Chinese
Bluetooth Connectivity:
The ZDOBD EPS001 Bluetooth Heavy Duty Truck Scanner connects via Bluetooth in just few seconds. No more tangled cables—just download the app, register, and you're good to go!
Real Plug-and-Play Scanner:
One-click automatic recognition to enter the system, avoid menu selection manually. The ZDOBD EPS001 is a plug-and-play scanner that's portable and user-friendly—perfect for any household.
Download ZDOBD App on Google Play or App Store (Search "ZDOBD")
Engine Inspection:
ECU data version information view
Fault code viewing and clearing
Real-time engine data viewing
DPF system regeneration, SCR system drive
Vehicle Function:
Engine Control, SCR Control, Vehicle Control, EBS, Transmission Control, Instrument Control, Driver Door Control, Air Suspension
ZDOBD EPS001 Function Highlight:
Portable and easy to operate
One-click automatic recognition to enter the system, avoid menu selection manually.
Regular OTA upgrades support continous model updates
Instrumet lamp introduction
How to use the product?
Step 1: Download the APP.
Step 2: Register an account.
Step 3: Connect the device.
Step 4: Scan the vehicle.
Step 5: Enable diagnostic function.