Hello everyone, please tell me the task of the proxy is to align a Jeep Grand Cherokee wl, I’m buying a two-way Vitch subscription and a subscription for opening a getway technician, but when choosing a proxy, the alignment asks for additional authorization, tell me who is responsible for this authorization
today i got a corsa C 2006 1.3 with mmarelli mjd 6J0 without DPF,read flash by obd with mpps and wrote the modified file with chksum corrected and now ecu doesnt communicate,also tried to write original file but without success as it doesnt communicate..
I have ktag eu clone and tried to read on bdm desoldering resistor but it stops at 75%.. I also have galleto but didnt tried yet,does anyone knows what is wrong with it?
Hi everyone. I would like to retrofit the selt belt extenders on a W205 Coupe. The parts can be found easily enough but can anyone help advise where this needs to be coded please?
Any help would be greatly appreciated.
I have a problem with my personal car, passat b8. Car was in a crash before, steering rack has been repaired or replaced. I can not get full steering end stops. I made steering angle calibration, end stops calibration but steering wheel turns 420 degrees but end stops are 500 degrees. Did anybody have a similar problem ?
Hi members i have a software guy who i use and until now has been good, he has left me with an install of ista unfinished and would like to ask if any helpfull members are willing to finish this install for me please. any help appreciated
Hi,
I plan to clone the ECU MED17.1.21 from my Golf 7 GTE, so I have questions for experts:
1. Which ECU do I need for this - is it enough if it is MED17.1.21 and the part number is correct or does it have to be an ECU from the Golf 7 GTE?
2. Is it enough if I make a dump from the original ECU and flash it to another ECU? Or does the EEPROM have to be adjusted because of the IMMO?
3. Which programmer/flasher would be optimal for this?
Hi . I need virgin dump for FVDI/VVDI to audi a4 b8 airbag ecu 8k0959655j eeprom 95640. I buy virgin file from xhorse for 8K0959655N with eeprom 25640 and when trying to protect the component with FVDI, I get an error that the file most likely comes from a different controller, and I cannot find a file for my controller number on sale. Original file from srs in attachments. Thank you for your help.
Hi all ive recently installed renolink 2.10 and im using a genuine obdlink sx cable, buadrate at 115200/1000000 and latency to 1ms. it says interface connected but will not find any units in the car (scenic 3 2013) i keep getting the message connecting but then changes to padding is invalid and cannot be removed, ive also downloaded v1.99 on another computer and its the same. the interface has been updated to the latest v5.10.1 and has a serial no 113011181544. any help appreciated
Hi.
I need ecu pinout from Audi A6 C5 2.5 TDI Quattro.
Ecu is Bosch 0 281 010 152
4B0 907 401 R
Below is a picture of the pins.
I've been searching the web for a while and can't find anything about this ecu.
Please help.
Thanks.
HI guys! I have a w463 (G500) with a water damaged ECM (A1131531991), tried to revive it but it looks like the second tricore MCU does not boot since I have no CAN or K-Line communication and the transceiver is OK ( I get TTL CAN data on the MCU RX pin but no TX) and there's data activity on the RAM of the first Tricore, both have clock on the x-tals, the rust was on the pins of the Bosch 30424, I would try to replace it but it looks like it is some sort of flash/ EEPROM.
I can get a cheap ME2.8 but it is from a W211 (A1131535479). Would it be possible to "convert" the A1131535479 into an A1131531991? (I have several chip programmers, Vediamo etc)
Hello can anyone here flash the Golf 8 Cluster with another SW Version because i have swap the rh850 chip from one cluster with broken pcb to a spare one.
The Cluster has Connection to the Chip but it dont show any picture
Hi all! I have ori 5q0959655BP flood damaged RCM from tiguan (R7F7010423 inside). Read DFLASH, CFLASH, EEP, OPTB0 from it. Got used 5q0959655BE. Tried to write all data from ..BP, got checksum error. Could someone help to clone my original ...BP RCM to used ...BE module?
