[attachment=51738]hello guy'stoday i receive from china 2 autocom . after the instal the program i plug the device on the usb port , the pc regognize as vci diagnostic unit but when make test from the program say :failed.
anyone has solution?
regard's
Year / Date : 2014
Version : 07-08.2014
System Requirements : Any Notebook
Language : English
Description : Clean Windows XP SP3 without drivers.
It takes time to upload and only 3 sec to press thanks and Rep +1 to show your appreciation.
That will give me more mental energy to upload more stuff for you all
Need the files for NCS Expert/WINKFP E60 CAS3 9227053, think is ista p V.37.
Had a bad flash in CAS3 and it as no VIN in flash and i'm trying to recover with WINKFP, i get connection with another 92something version when i press vol+ to force wake signal and the CAS responds, does the first chech(first bar to 100%) but then error and i think it's because of diferent ver. number. Any help would be welcome
Hope everything is well on your side.
I bought an original DME Porsche from its factory.
Would you please let me know do you know someone to programing and coding it?
We have a Porsche Piwis Devices, do you know anyone who has Porsche account to get advice from him from Team Viewer to ask him how to program DME?
Please send the information if you have them.
Please notify this information is so important for us and it should be in secure. because as you know well, this information is very valuable.
Hope everything is well on your side.
I bought an original DME Porsche from its factory.
Would you please let me know do you know someone to programing and coding it?
We have a Porsche Piwis Devices, do you know anyone who has Porsche account to get advice from him from Team Viewer to ask him how to program DME?
Please send the information if you have them.
Please notify this information is so important for us and it should be in secure. because as you know well, this information is very valuable.
hello i got a vw polo magneti marelli 032906030P ecu and want to get immo off how can i do this which chip do i need to read?
does any one have picture?
HI ,HOW TO READ PINCODE FROME ECU CORSA D
E 83 55576685 AAPL
ACDELCO.
1.WHAT TOOL CAN READ PIN?
2. WHERE IS WRITE PINCODE IN EPPROM OR MCU?
3.PINOUTS FRO THIS ECU PLEASE.
THANKYOU
Year / Date : 2014
Version : 9.30.002
System requirements : PC with Windows, the software interface supports Techstream (Mongoose, miniVCI, MVCI, Openport 2.0, AVDI, CarDAQ etc.)
Language : Multilingual
Description : You can put on top of the installed versions or from scratch
It takes time to upload and only 3 sec to press thanks to show your appreciation.
That will give me more mental energy to upload more stuff for you all
lost all BMW CAS 3+ key and need a spare key, which BMW key programmer work on BMW CAS 3+? BMW multi tool or Digimaster 3 or AVDI? Any experienced BMW locksmith options?
I am In need off an alternative connection on a: edc15p ,29f400boot pin .
was flashing a audi today when my bro in law decided to disconnect the battery to the car have way through programming .
wrong car I meant disconnect battery on seat leon.
anyway couldn't connect to it with either mpps ,galletto 1250 ,fgtech v51 or fgtech 54 .
soldered a wire on the boot pin to connect in boot mode. wouldn't connect on bench . so tried on car , disconnected dash etc first got bro in law to touch pin to ground , upon doing so he pulled the f**^%%g pin off the chip . mad aint the word .
cannot connect to ecu to even read immo code off 24c04
ecu is 045 906 019g is there an alternative edc15 I could use whats easier to get hold of . and write the original file from the a2 to it and remove the immo .?
or do we have another point on the circuit that pin 24 connects to ? so I can dremel into chip connect a wire and hopefully get this thing working again .
forgot to ask anyone got an immo off file for 24c04 eeprom .as I cant read it was gonna try to flash eeprom at least tomorrow see if that's working
Can someone give me some info on how the immo works on the clio 3 1.5 dci.
The only key has died. The remote works , but the transponder is dead.
Since there is no immo off solution, I have bought the zedbull to make keys.
I have blank ID46 transponders PCF7936. Basically I have 2 options, To prepare transponders for programming or to write the transponder in the UCH dump.
If I prepare the transponder I guess I have to use canclip and a pincode to register the key.
If I write the key in the UCH dump, do I have to virgin the engine ecu?
My Vag-com does not work anymore, the cable problem, I use the Genuine Ross-Tech VCDS cable to 11,113,
I did the shit, clicking the MProg2.8a when I install Galletto 2, I forgot that the vcds Cable was plugged in, it changed the firmware of the cable and now it does not need help to return to normal
![[Image: ab77950ae2e5444774de3bb889cd3250.jpg]](http://i66.fastpic.ru/big/2014/0730/50/ab77950ae2e5444774de3bb889cd3250.jpg)
![[Image: 650d83af8420b0b77aca08aa95c2d54a.jpg]](http://i66.fastpic.ru/big/2014/0814/4a/650d83af8420b0b77aca08aa95c2d54a.jpg)
