Greetings to all Members. I recently installed Xentry-DAS 3.2014 ( from this forum) and generally it works OK. However today I've encountered some problems with W220 Active Body Control. When I try to access the module it gives me error message : Communication Software Error (1.2)-2.592. It is very strange as about year ago I did the same job using Xentry-Das 3.2013 and all went OK. My suspicion is that there are some files missing in my 3.2014 installation. Can anybody help in the matter? Please.
Hi guys,
I have a Bosch KTS 520 for daily use and a few days ago I lost communication via USB or Serial.
There is no USB detection whatsoever, I checked and switched cables, nothing.
I then tried the old serial COM and no communication on that port either, Bosch DDC can't detect or test the interface.
I tried both via car's OBD port for power and external power supply, the green LED flashes like it should and at power up I can hear the relays activating but there is no communication on either ports.
I went to a GSM store and replaced the PDIUSB IC near the USB connector, wich handles communication but nothing, nothing at all. If the USB is bad I guess at least the COM would work but it doesn't.
Do you guys know anything about this ?
Requested by some mhhauto members, here is dashboard service tool V1.8.
Protected with themida and hardware protection, on this software may pop up some error messages even with the original version, especially if you browse on the car list with an open file, as shown on this pictures:
Cracked:
Original:
About the program itself, I've tested on a few files available here on forum, and it worked but I leave the review test to all of you.
Last but not least, the loader was packed with themida and, on some antivirus, may fire up the virus alert.
I have a mercedes w208 clk230 kompressor which is from another garage and they have a ecu, key, ignition switch from scrap yard, the car starts and runs but the windows, mirrors and boot lock not working! I have inside the car only original ecu thats it!
equipment i have access to:
1.Mercedes xentry 03/2009 Dev mode
2.Mb nec prog for key but not good to read!! maybe only write!
3.rosfar r270 programmer
4.carprog
please advice on what and how in steps, from what i have read it's the 2nd hand units which are not coded right! needs eprom read and post on here to be virginised but i dont know which eprom and how to connect to read with!
any help and point in right direction would be highly appriciated
The SVGVOpen SVGViewer stopped being compatible with the upgrade to internet explorer 9, to see schemes have to uninstall internet explorer updates up to I8
We're going to control panel-uninstall programs-see installed updates
Hi Im a new member, my car is a seat leon 1.8 T AUQ 180 KM I want to pull up my engine to 210-215 KM by soft (map engine) This is my oryginal file ECU. I will be gratefull.
Hello,
I have on my hands a hybrid delco HSFI - 2.1, 09353459.
I searched a lot, but I would like help from some guru here.
The strings lose the contact very often and they have to be reconnected.
*Is any technic to take off the gel? or just scrap it
*I have a classic solder iron and not ultrasonic, will the strings stick well or after a while they will the contact again?
Hi got a 03-04 Mondeo 2,0 TDCI in the shop.
Need to read/write to it and im looking for some tools for this.
The ECU is labled 4s71-12a650-gb and got a Delphi badge on it.
I tried CMD flash (OBD) -> DCM 3,5 but wont read.
Is my ecu DCM3,5 ?
If not what is it then and what kinda tools supports this ECU ?
Hyundai USA 5.1.5.0 [02.2010] English
Win | 1.18 GB
EPC for Hyundai Cars, spare parts for all models from USA.
Hyundai EPC is an electronic parts selling system for fast and accurate parts interpretation. Hyundai EPC covers all Hyundai passenger cars, R/V and commercial vehicles and buses made in USA.
Homepage -
Code:
http://www.snapon.com
Requirements:
- O.S.: Windows XP; Windows Vista; Windows 7; Windows 8
- CPU: Pentium/Athlon 1.8 GHz or higher
- RAM: 256 MB of system memory
- Hard Drive: 5 GB of available space
- DVD-ROM
Chrysler PAIS 4 [07.2015] Multilanguage + Activator
Win | 8.16 GB
Chrysler Pais International 4 - Spare parts catalog for Chrysler, Dodge, Jeep, Plymouth, Eagle, all markets, VIN decoding 1984-2015.
Homepage -
Code:
http://sbs.snapon.com
Requirements:
- O.S.: Windows XP, Windows Vista, Windows 7, Windows 8, Windows 8.1
- CPU: Pentium/Athlon 2 GHz or higher
- RAM: 512 MB of system memory
- Hard Drive: 10 GB of available space
- DVD-ROM
Dialogys - an electronic version of documentation for RENAULT and after sales car RENAULT, DACIA. Dialogys includes absolutely all repair manuals, diagnostics, and parts catalogs for all models of car brand Renault.
- O.S.: Windows XP; Windows Vista; Windows 7
- CPU: Pentium/Athlon 1.8 GHz or higher
- RAM: 256 MB of system memory
- Hard Drive: 15 GB of available space
- DVD-ROM
BMW ETK contains the full range of parts offered for sale by BMW Group and is intended to facilitate the retrieval of necessary spare parts (car parts and motorcycle), supplies and accessories. Added to the price list in the BMW ETK Local with ETK Admin.
To do this at your disposal a variety of search functions, such as searching by name, by part number, etc. In addition, the system offers
detailed information on specific details, as well as the ability to create so-called parts list of found parts.
- O.S.: Windows XP; Windows Vista; Windows 7; Windows 8
- CPU: Pentium/Athlon 1.8 GHz or higher
- RAM: 256 MB of system memory
- Hard Drive: 10 GB of available space
- DVD-ROM