Hello all

I have Vw amarok 2011. Edc17cp20

I make new key show safe on instrument , I made immo off for ecu still same problem no voltage pulses into injectors !!!!!!
I read fault code show me that only fault code : U111200 : function limitation due to implausible message !


I read data stream as shown
[attachment=55039][attachment=55040][attachment=55041]


I have onther edc17cp14 , if I write ori flash file from to edc17cp20 to it , will it work ???

Or doing immo off directly ??

It's for Audi a4 , will work with Vw amarok engine ???


I don't know where is problem is ???

Thanks

Hi all, I need help with the reset brake pads on a MB 204 YEAR 2013.

I have tried using the manual procedure ASSYST PLUS and also reset ICM whit scanner (maxidas) but it only resets OIL SERVICE ................

It is only possible with DAS XENTRY?????

Here you go

Attached Files

icom3_10_46.txt

1080

21 bytes

Download

Hey Guys. I have an E92 that I just installed a Junction Box for Electronics 3 (Part # 61 35 9 329 800) and Front Power Distribution Box (Part #61 14 9 119 445) and now the iDrive screen and the radio doesnt work. I logged in with ICOM (Ista/P) and the modules wont program. Anybody have any insight on the steps necessary to code the module so the system will function again?

please code for 6000CD
PART NO 8c1t-18c815-ac
S.N V014899

Hi !!! Please someone has IDS V90 patch .....Thank you !!

WE HAVE A LOT ELECTRONICS USED PARTS FOR TRUCKS MAN RENAULT VOLVO MERCEDES SCANIA FO SELL
WE HAVE MAN EDC , FFR ,PTM (ALSO PAIRING EDC/FFR AND EDC/PTM)
WE HAVE RENAULT VOLVO EDC , VECU (ALSO PAIRING EDC + VECU )
.............................................


INFO BY PM





MOROCCO

please code for 6000CD
PART NO 8c1t-18c815-ac
S.N V014899

hi
can anyone advise how or where the connection are at on the dash of a c class w203 (2003 model) for the connection of the ST49 cable as suggested in the digiprog menu or can it be done some other way .
I am using Digiprog with version 4.88 software

Martin

hello. nead orginal file? thanks
75vG.
0281011342103737
1037376576B075WF
75WF
SS03C87B000287__O8XW

Megane II 2006, 1.5 dci

Cruise control dont work. Speed limiter works.
I cant set the speed.


Clip shows the error df 127 3 def. The position stop switch outside of the tolerance.

I tried to replace the brake switch and reprogram the computer.

Please help.

Hi,

I need immo off in Seat Cordoba,TDI.


Car: Seat Cordoba 1.9TDI
Ecu: Bosch MSA 15.5-7.1 0281001584
Dump: B58253=24C02

Please need tested file.

Thank you ,

Attached Files

24C02 ori.rar

59

1.36 MB

Download

Good for all.
I need urgent help.
I've scanned a 2005 BMW e90 530d, with PASOFT 2.1.0, I deleted all errors and after the car will not start.
It seems like it has battery, giving the contact dash off.
The needles go crazy.
Do not understand what could have happened, I think it has some corupted file lkm, cas ...
Can anyone help me out, and known to cause this error? They will kill me and do not start the car .... just wanted to clear the airbag, (


this is the logs in pasoft and files.cod.... i dont now how to use to recover... if is posible.

Many thanks in advance

Hi guys i need original dump for speedo from Audi A3 8P0920980M - eeprom 93c86

with immo off if its possible

Thank you

hi, need help to remove DPF for Nisssan qashkai 2.0dci 150PS

thanks in advance

Attached Files

0281013855_nissan)qashkai_dpf_org.rar

58

67.18 KB

Download

i have bought this programmer i think its based on the rosfar r260 and no software came with it, typically my luck!! i would be very grateful if any one could point me in the right direction to download it, many thanks in advance..

Can someone help me? Correction in Audi A3 FSI instrument cluster binary correction to 149503 and Peugeot 307 2007 bsi and instrument cluster to 143205.
Many many thanks!

Attached Files

Audi_A3_93c86_original.rar

23

1.09 KB

Download

peugeot.rar

23

5.84 KB

Download

I have problem,can any one tell me how to install bosch esi software 2014/2?
thank you so much

(10-02-2014, 10:19 PM)oemtool Wrote: I have problem,can any one tell me how to install bosch esi software 2014/2?
thank you so much

Help fap off
307 1.6hdi edc16c34
0281011630
1037374174
Volta does not work

Hello guys!

I need virgin dump for that Bravo.
If someone have ill be happy
I have problems with corrupted memory inside

Regards

Hi All,

Please see attached pics of my new VCMII that arrived today.

1. Does anyone know from the pics if this is any good for programming?

2. Can it support Wifi

3. What is the 8gb memory card for?

4. It came with 86.01a, Is this the best version to run on it? Shall I leave it as it is? Is it worth getting a newer version?

5. Last one, I hope! Do I need to get calibrations on disc from somewhere?

Thanks

Hello.

I have a Ford VCM2. It works with v86 IDS, but I'd like to use it with Mazda. To another pc i have installed V88, VCM manager says its not connected, but in the pc device manager i see it (ETAS). How can i make this work?

Hello.

Want to update from V80 to v75. Network is ok when usb is plugged in, but IDS not communicates with the VCM. File version check in progress, but no success. I ran CleanVCMutil.exe it says FAILED. What is the solution?

I am looking ORI for:
HONDA CR-V 2.2L i-CTDi 103kW/140hp 517655 (1037517655)

Thanks

hello, i need sprinter ezs module modified to 0
dump attached. thank you

actual ~506tkm

Attached Files

0L01Y-1002(22)EEP(S136157_BENZ)ok.rar

69

781 bytes

Download

Hi.
Need isn number from this file .
Anyone could help with this?

Regards Marko

Attached Files

bmw_318_e36.rar

23

44.06 KB

Download

Looking for workshop manual for honda crv 2013
tx

anybody has it ? plz tell me

HI GUYS
I NEED DPF OFF BENZ 221 320CDI , BECAUSE MY WinOls is broken .CAN HELP ME ANYBODY?
THANK YOU

Someone can help me radio code for Smart

MC341631223931