Hello!
I have this problem. I did some Sprinter and vito before by repairing WSP and ECU dump. As I know ML is other story. In FBS I have Tranponder fix code fault and in Actual values-->Key in ignition switch: ----
Any info about this? Wrong reader coil?
Hey. Looking for materials about Terex Pegson crushers 1100 X 650 or similar. I need mainly electrical and hydraulic diagrams. Or any of the data for this and other models. Regards
I got a 2014 CLA250 4matic in Canada. Have a rear end accident. Driver's, Left rear passenger, Right rear passenger seat belt retractor deployed. I replace all 3 belt and reset the airbag module. All error erased from airbag module. Look OK! But got a PRE-SAFE FUNCTION LIMITED message display in instrument cluster. Got C3200 code from COLLISION PREVENTION ASSIST controller unit. Anybody knows about C3200, is it a crash signal? I try to erase it, it can be erased. But it will appear after next ignition cycle. Seem like some other module send a error signal to COLLISION PREVENTION ASSIST to triggle the error.
Since it is a totally new model in our country, Any help will appreciated!
I'm sorry if I posted this in the wrong section, i'm a total novice to this forum. I used TizWaz's keygen method to install hds 3.012.030 for the honda interface module. Everything works great, except for the IMMO. Can someone help me?
Hello can anybody help me i have golf 4 1.9 tdi 1999. And i was trying to chip tuning the ecu and now car dont start i guess i fried the chip.. So i have new Ecu found and to start the car do i have to reprogram the new ECU ?
BMW ISTA / D versions 2.XX. At this time, comes the official dealer services .
In version ISTA 3.43 was fixed 253 errors that were obtained through user reviews .
Extras. information:
- Works only with Ediabas 7.3. Present in the distribution
- Before use, you must install the Redist folder of files 5 .
If they are already installed , you do not need to install them knit .
a) vcredist_x64.exe for Win x64
b) vcredist_x86.exe for Wind x64 and x32
c) vs90_piaredist.exe
d) NET Framework 4 for Win XP, Win 7 x32, x64
e) NET Framework 4.5.2 Win 7 x32, x64
Install:
- Put the patch in the folder Rheingold / TesterGUI / bin / Release. When ask "whether you want to replace the files?" click "yes"
- Use the latest version of Winrar 5.01 or 5.1
- When extracting the main archive, enable the option "extract damaged halyards" (Keep broken files)
- If you notice any bugs in the program, write about it on the forum
- To remove the popup "USAGE NOTES" in line after faile ISTAGUI.exe.config
add
Year / Date : 04 /2014
Version: 3.43.10
System requirements : Windows XP x32 and x64, Windows 7 x32 and x64, Windows 8 x32 and x64
Language : EN, DE
can someone point me to a working copy of ETKA, single download not 10 different parts. I have downloaded a copy from here, but theres no installer that i can find now that I have unpacked it. please make sure it includes the serial so that its usuable. I have been trying to get a working copy of ETKA for almost a week now.
wanted to change my bin file mileage to reflect used engine we just installed cant figure out where to find mileage current has 241954 kms need 156789 kms any help or suggest would help
I use GQ-4X, good USB programmer. to read the eeprom and used calculations from tachosoft but tachosoft was wrong as to where the mileage is stored perhaps there is some other program i could use to find and change the kms?
After spending countless hours trying to get my SD Connect clone working without any results, I though I might seek help here, as many of you have good knowledge about the SD Connect hardware.
I have a C4 china mux that is not behaving properly, and I need some help troubleshooting the hardware. At the moment I am running Bootimage version 2.2, CSD version 2.5, and PMPic version 2.9. I am not able to update or downgrade the PMPic through Toolkit, so I have to program it with PicKit directly on the circuit board, even if all the other chips updates just fine through Toolkit when removing the pmpic.hex from the update files. I have tried numerous firmware combinations, and I still get the same errors regardless of which firmware versions I use.
The caesar test throws me an error saying that it is a problem in communication between the SD Connect and the diagnosis computer, with error number "5" (but the caesar report is still showing the version numbers of the different firmware, and the IP addresses). It does not test any hardware components, like the RAM chips, CAN bus, etc..
DAS gives me a (1.3)-3.505.9617, even though the relays click on the two tries it makes to communicate before the error message appears.
As far as I can see the network PCB works fine (network works, both LAN and WLAN) and the LCD PCB works fine. The main board however seems to be the culprit. I have tried the mux on version 09.2013, 01.2014, and 03.2014 of Xentry, with different computers and both virtual and native installs.
I have tried searching for answers both on this forum, and other places, but I cannot seem to find any answers to my mux' problem.
Does anybody have an idea to how I can continue my troubleshooting? Some of the forum members must have experience with repairing SD Connects, and knows which components that often fails or which components that are likely to fail?
I have tried in vain to obtain a PCB diagram for the C4, so if anybody has a copy to share that would be great ...
The seller is very reluctant to allow return for repair, as all the Chinese businesses are, so any help is appreciated. I would like to try a little more before I send my hundreds of dollars worth of electronics into the People's Republic of China without ever seeing the mux or my money ever again ...
dongel [/size]
I have autocom software if somebody likes to make crack for that
