One time or another i was looking for something like this but couldn't find it
So i though of making it my self
Donar Car was 1998 528i Saloon
I used NCS Expert to pull out Configs
Opened with NCS Dummy
Best viewed Via Full screen at 720p
Or just follow the links
I never found The Solution of this problem.
What do you use as an extra power when coding by ista, or winkfp.
I have a problem with that.
Thanks for your help and share this experience.
Hi I need help with my sd connect working with 1/2011 xentry I keep getting in das 870 error how to fix I tried 870 blacklist fix still no help is the firmware to new in my mux I do have xentry running on 1/2012 works good but I would like to make it work with 1/2011 also thanks
One time or another i was looking for something like this but couldn't find it
So i though of making it my self
Donar Car was 2011 E90 328i Saloon
I used NCS Expert to pull out Configs
Opened with NCS Dummy
Best viewed Via Full screen at 720p
Or just follow the links
Hello, can some one help me clear crash data please?
Keihin 77960-TF0-E832-M3
i attach 2 dumps, 1 is original dump data flash, the other is
data flash cleared, i tried clearing with Airbag Service Tool but i have 1 DTC srs internal error & wont erase with Diagnostic tool.
Thanks
Hi guys, I tried to edit a file in my 320d 150hp, I would like your opinions possessions, and if I did it all by ca ... or dogs tell me mercilessly.
and perhaps on what I did wrong,the file and read with mpps.clone
HI GUYS
i need the help i install auto-cm 2013 without problem i test usb test ok
but when i update firmware gives messages:
Problem can:
1: cable pc not connect to pc
2: Power cable not connected to the tester
3 selects com port not available
please i need the help
thanks
Hi, I've looked for an answer on this but no luck. Sorry if Im re-posting... Im a newbie.
I have a 2012 Honda Civic that I am trying to hook up to a Digiprog III v4.88 via an OBD cable.
The issue is that the under Cars > Honda > Civic, there are only 2 choices both of which do not work. I think they are for older Civics. Ive tried all Honda's and no luck.
Ive tried some other cars too... I know the cable works but I need to find the right car to read/write to the EEPROM.
I had a 2008 Civic and it has the same dashboard config so I assume 2008-2012 will be the same.
Somebody must have done this before, the Civic is one of the most popular cars in North America.
Does anybody have any ideas how to get this to work?
Hi guys,
I have this small Pejo 206 for work, its a 98' 1.4i KFX engine, TU3JP with manual transmission and AC. It has Magentti Marelli ECU.
I changed all fluids, spark plugs, filters, coolant, AC refrigerant, timing belt, auxiliary belt etc but I still have this issue:
- Most of the time (like 80% of the times), in the morning when I start the car, at the moment I turn on the lights or turn on the AC or anything that loads up the engine it struggles and stalls. Atfer it warms up a bit it doesn't do it anymore, just in the mornings or when unused for several hours.
I cleaned the throttlebody even if it has no gunk at all, suprisingly clean.
Anyone familiar with this ?
Idle control valve ? Throttle position sensor ?
Today, I updated ewanet at the 4.2014. 1.2014 version works very well, but the current does not work. Clicking java EPC does not work. english operating system does not work when it works but when Turkish. How has a solution.
I have problem ,i buy a car and in ecu are 5696 fault testing with bosch kts , eeprom checksum fault , i try find explenation in google, but i can't
find maybe some one can explane me problem ? or solution ?
I have tried from the engine control unit A6461502279 from reading the data and to replace spokes (see Appendix), and then the broken ecu (A6461502279) through these parts number (A6461532179) (but without success)
while writing the read flash files is an error came and stopped right at the beginning.
Im needing the injector IQ figures for my ASV 110 tdi octavia 52 plate.I also need info on amount of fuel acceptable in leak-off test etc.
I went to skoda & they say theyre not allowed to give out info anymore due to liabilty issues.not even allowed to give out tarque values either.!!
Can anyone help me please?I will give you VIN/Reg in a PM if possible as dont want to publish info on open forum for obvious reasons.
ps:I read online that some asv engines are 3-5mg/stroke,and others are 2-9mg/stroke.But I would like to be sure 100%
ALSO,My leak off test showed that injectors 1 & 2 returned absolutely no diesel,while injectors 3 & 4 returned about 12mm & 18mm of fuel in 3.2mm inside diameter tubing. Also,would this suggest 3/4 or 1/2 are bad?
i am having trouble in disabling the immo on this passat 1.8t AEB. i have manually tried to disable and the recalculated checksum. but car doesn't start, and comes with 'start blocked by immobilizer' code.
i have attached ori and mod 24c02 binary, and also a screenshot of the editing.
BMW ISID ISTA-D Rheingold 3.42.40 ISTA-P 2.52.40 Asus F3 Acronis HDD image
New diagnostic system of BMW vehicles. It works with E and F series. BMW Rheingold is the replacement of the diagnostic program
BMW ISTA/D versions 2.XX. At this time, supplies to the official dealer services.
The programming system ISTA/P is an application of ISPI network. With ISTA/P you can do coding, programming and replacement of control units.
Date: 03/2014 Version: D3.42.40 & P2.52.40 System requirements: Dual-core processor, min. RAM 4GB Language: Multilanguage
NB!
- Image restore through Acronis
- Enter through admin mode to setup drivers for your laptop and choose screen resolution for your LCD. Drivers can be found here http://drp.su/ or you may have your own
- Video: How to restore HDD image through Acronis:
and need to downgrade to V5 by reprogramm 
![[Image: 2fe84f8d70bfc4fe3a4af1f8333562d6.jpg]](http://i62.fastpic.ru/big/2014/0521/d6/2fe84f8d70bfc4fe3a4af1f8333562d6.jpg)