Does someone have a schematic for a Renault Megane II key card. I was trying to open it and change PCF7947AT chip. After opening I found one resistor and 6 pin chip damaged. Want to know what type they are.
Thanks in advance.
Hi m8 i need please the immo off of this ecu edc16c34 0281 011 629 06:11;19 here is the original dump and i need also the position of the dump in the ecu, thanks.
Hello, i see this product: http://www.mtx-electronics.com/prodotti/...hex-editor
I translate description:
This software is an hex editor specifically developed to work on EEprom (E2P) engine control units. The user interface is optimized to work with both the original file and the edited one at the same time allows the synchronization of the two files on the movement. For EDC16 the checksum is calculated automatically when you save the file.
Some features:
- Displays both the original and modified files;
- Synchronizes files between shifts;
- Highlights the areas of files that have changed;
- Separate bookmark for both files;
- Calculate the checksum automatically (only EDC16);
- Highlights the areas not covered by the checksum of the file.
I'd like to have suggestion, because i'd want to buy it... what do you think about it? It seems an interesting sw, because it's useful with immo off or mileage on ecu...
Hello
I need good dump for Mondeo petrol 2.0L 107Kw
ecu VISTEON 4S71-12A650-RC LBO-113
8AWC
eep 95040
my dump is deleted
a colleague was trying to create something but deleted eep!!!!
Please help
Thank you in advance!!
Best regards
Hello Can somebody help me calculate pin code for Iveco-Eurocargo 2002 year model eeprom 93s56 immo-box Bosch. thanks
I am attaching 2 files I need the pin code
Today cames a engineer to the eschool and told me INSITE 8X is coming the firts quarter of 2014, my question is if any one knows if this new version is gonna be like a update and we still working with the same code key from insite 7.5 or we are going to need a new one key?
Sorry, I have a lot without writing inglish, hope to everybody can undertand, thanks a have a new year.
Regardes all.
Some procedures for working whit vag com.
Most of them are in word format.
ESP Steering Angle Sensor Calibration
Cluster Swapping in Vehicles Without Immobilizer
Immobilizer 3 Measuring Blocks
Immobilizer II ECU swaping
Immobilizer II to install a NEW Instrument Cluster
Immobilizer III ECU swaping
Immobilizer III install a NEW Instrument Cluster
Indicator VW reset VAG-COM
Matching keys _4-digit SKC
Matching keys _7-digit SKC
Suspension Level Control Calibration
TDI VAG
Throttle Body Alignment
VW Service Interval Reminders
Xenon Headlamp Adjustment
Hi guys. I can not read this ECU IAW 5sf8_p2 G.P. natural power, follow the pdf cockerel ST_10f296 but goes into boot mode. Where am I wrong? I would just like to read, I have tried with no AutoCom only boot mode pin K-line or CH + / - and 5 + and 5 - but nothing to do. I can not find anything on the internet to help me, just that. But I tried to make connections but nothing.
Hi
I have a strange problem when installing the autocom 2012.3. autocom for trucks works perfectly, the autocom for car installs , I change my path and dont give Activation file (before I replace the path, the program gives me the activation file but cannot activation
can someone help me?
Did you know if you have or not to crack the OiC. Power Latin America - Iveco. Because the power is somewhat complicated and this is a little better. If you have to respond. thank you
So I have Autocom clone with 2013 R1 software. Installation and everything went fine, but every time I use Autocom, have to remove VCI from the bluetooth devices, search and pair it again or the software won´t find it.
What possibly could cause this kind of behavior?
Who has the golden versions of Xentry / DAS, that would love to share with us on the forum.
All available links on the forum are at the moment down.
I have tried to search 01.2011 / 07.2011, if there are other 'golden' versions please let know & try to share / seed torrent !
I would prefer if it's a proper pre-installed acronis image or gho.
1 x Original CMD Slave interface (license till end january)
1 x Position Frame with a few adapters
1 x Labtool - 48
1 x 10 Adapters including:
- SSOP 30 PIN
- SSOP 48 PIN
- TSOP 48-2
- QTD64-B
- PLCC20
- PLCC44/D44
- CFP-44-825
![[Image: 9jnl94.jpg]](http://i46.tinypic.com/9jnl94.jpg)
Hi guys. I can not read this ECU IAW 5sf8_p2 G.P. natural power, follow the pdf cockerel ST_10f296 but goes into boot mode. Where am I wrong? I would just like to read, I have tried with no AutoCom only boot mode pin K-line or CH + / - and 5 + and 5 - but nothing to do. I can not find anything on the internet to help me, just that. But I tried to make connections but nothing.
(before I replace the path, the program gives me the activation file but cannot activation 
