need help coding this VG transfer case module, cannot find options for the car, dealer cannot find via vin for me.
i need to code optione:
1.tire size (265/60 R18)
2.Axle Ratio (ha= 4,375 / 4,111 / 4,857 / 5,286)
3.Lamp Output (activate/do not activate)
4.Lock Switch (activate/do not activate)
I know the tire size. But #2, axle ratio -- i cannot find the correct option to select. Please Help!
also, #3 lamp output and #4 lock switch, what are these options?
I have alot of older dvds from chrysler that I might share... most are 2005 range like certain dvd release for certain models. Not even sure what is on all them just checking if anyone would be interested in them if I was to upload them.
I think most are service dvds etc. I realize this isnt much info but I dont have them on me at the moment.
I need a little help with replacement of my CCC unit. The car is 05 E60 with a Professional Nav unit which was failing, so I decided to replace it. I have a friend who has two used CCC units for sale which I took in order to fit. One is the same as mine from a 04 car, the other is the Facelift model from a 07 car.
I have tried both of them to my car but they were stuck on the BMW logo and wouldn't proceed any further, so I decided that it would need some coding. I've hooked up the ICOM and started Ista P. At first I noticed that ISTA wanted to program almost the whole vehicle which I did. After that I have Programmed and Coded the new CCC unit to the car.
Just after the procedure the unit worked OK. It booted. Played CDs. Showed the on board computer etc. After that I locked the car and left it for about 5 minutes, unlocked it again and the unit just powered on showed the BMW logo for approximate 1 min. and restarted. This process repeats infinitely.
Have this PT Cruiser from MY2002, 2.0L engine with this fault code stored. Seems to be an internal controller fault.
Will come back after reset and start.
Anyone fixed this before and have some tips for me?
Hello
maybe someone can help me
I have a mazda 5 143cv with denso ECU the machine works perfectly and then after about 30 minutes car off turn the key and turn on the fan turns on and the car will not turn over, if I remove the ECU for 30 minutes and reassemble the car works well !!!!!
sorry for my english
AVAILABLE FOR THE FOLLOWING MODELS WITH NAVIGATION RT3
Peugeot 807
Lancia Phedra
Citroen C8
Fiat Ulysse
+ Others.
To know the version of your software hold menu button a few seconds, a menu will appear, go to the system info, and look under 'sw sistem':
if the firmware is 5.xx or 6.xx your device is a NaviDrive RT3
Download and unzip the. Iso.
Board of burn to CD quality: avoid those 'thin' (if you look at them against the light you can see through it), because they make it difficult to work the laser reader of the navigator, especially if he already has a few years on his shoulders ...
Always burned at low speed: 2X advice.
Well, i have a Lexia that is giving me a nice and big... headache!
Well, it is a clone, and it's working ok with Diagbox 5.XX.
Mister ScaryMistake updated it and all worked ok
The PC sees it as it should and version is ok.
But... BUT! To work ok on Diagbox, the LED must be ON all the time,
and LED is ON only after firmware update.
If i make update and i work with it, is OK, but if i unplug the USB and put it back, the LED is on for 2 seconds and then turns OFF . Wich means i have to do firmware update every time i use IT!
I updated a video to youtube wich shows exactly the problem!
Hi all , merry Christmas.
Can someone please help me with a virgin dump for Mercedes Viano w639 instrument cluster.
Cluster part number A639 900 5600
eeprom 25LC640
merry xmas to all
dose anyone now what it is that go's in the bosh vp44 diesel pump ecu or any were i can buy book program to help me
cheers lads have a good xmas and dont for get dont get to drunk
This is my first post in this page, but I'm online 05-31-2011.
I wouldlike to ask where is the VIN in this NAVI and somebody help me change VIN? I can pay.
I hope that I will be actively take part in life this forum
The TecDoc CATALOG is a flexible information systems, which allows you several personal settings to ease your daily work. TecDoc supplies the free vehicle spare parts market with current and comprehensive data for identifying and ordering parts – for both, PC as well as CV – directly from the databases of the cooperating automotive aftermarket manufacturers in a standardised catalogue form.
- O.S.: Windows XP; Windows Vista; Windows 7; Windows 8 (32 or 64 bit)
- CPU: Pentium/Athlon 1.8 GHz or higher
- RAM: 256 MB of system memory
- Hard Drive: 40 GB of available space
- DVD-ROM
Toyota EPC program contains schematic device of all Toyota and Lexus. The program is very simple and easy to use. Allows to determine the year and month of manufacture cars by make and frame number and part number to find parts.
- O.S.: Windows XP; Windows Vista; Windows 7; Windows 8
- CPU: Pentium/Athlon 1.8 GHz or higher
- RAM: 256 MB of system memory
- Hard Drive: 20 GB of available space
- DVD-ROM
headache! 
![[Image: tecdoc_multilenguaje__espa_ol_1.png]](http://sertecomp.net/web_images/tecdoc_multilenguaje__espa_ol_1.png)
![[Image: juiws6.png]](http://i41.tinypic.com/juiws6.png)
![[Image: en_description.png]](http://webdocuments.org/web_images/en_description.png)
![[Image: en_system.png]](http://webdocuments.org/web_images/en_system.png)
![[Image: toyota_logo.png]](http://sertecomp.net/web_images/toyota_logo.png){kind=logo}