I got a used Genuine C3 Mux from Mercedes, but I'm confused with the Pinning of the Round Connector.
Can anybody help me to connect it to a RS485 or RS232 Interface?
I've found some schematics here, but I think they are all for the clone Mux.
I just got a new SD Connect C4 with Xentry 05-2014. After setting the LAN cable connection which now works fine I'm having problems with the Road WLAN connection. All settings were done correctly, I see that I have active wireless connection Peer-to-Peer with excellent signal but I still have red color on the MUX side and I can not select Road WLAN connection because the OK button is greyed out. So, where is the problem ?
I would like to buy tool for Vag and seem to be datasmart and vvdi can do that job even immo 5th generation, so if you can give your feedback and experience it will be great!
About vvdi he is always based on the old AVDI version?
I have a problem with my Opel Astra G 1.7 DTI ECU (ISUZU system). My old ECU died. I changed it with a used one. I had the transponder and the receiver with it. My engine starts but the motor fan doesn't work. I tested everything and all is ok. The ECU simply doesn't send signal to the fan. The model of my "new" ECU isn't the same as the old one. I need to buy another one with the right model number, I think.
I wan't to buy one without transponder and get the pin code from TMS370 in transponder an get PIN code with xprog to program immo in the ECU I will buy. Is it possible to do so? I have Opcom but I don't know how to do that and need help.
Hi.
Problem with broken Dash on `06 Ocatvia.
Tried to add keys by VAGDashCAN, this caused an error and Immo is not responding anymore. Adress 17 and all cluster functions working. Adress 25 is dead. Even no more Immolight when turning on the Ignition.
I hope this is just because of corrupt data...
Dumped the AT24C16 from Dash.
Is there a chance to recover the file with donor and retrieve PIN for KeyAdapt?
hi, every time i try to ead the mileage on the chip its just saying "old mileage 0 Verify" but its not 0. i have digiprog 3 clone its V4.88 and its a 2011 relay. help is much appriciated
vf1fc07bf33921720
This is the chassis of a kangoo we have in that has a solid red immobiliser light on since we had battery out for gearbox change.. If possible I will try to code key again as done this on clios before. If anyone could give code for key programming would be very appreciative. This van is now starting to hurt my head as thought it was just inertia switch had activated, but not. Aaahhhhh going mad after 27 years in a garage. Thanks.
Hello, now i have install Vediamo on my PC. But how does it works?
Whats are the Steps to start Diagnose and Programming KI ect?
I am a little confused.
I have a Problem with my Xentry 11/2012. It works very fine with C3,
but I have the Developer mode only for Cars. ForTruck und BUS I have
no Developer. Why? It's not available for this or is my key not correct?
Hello,
I hope and wish anyone can help me on this matter.
We have a Seat Leon 2008, which we've replaced the Airbag control unit because it have stored a fault code:
---------------------
Address 15: Airbags Labels: 5N0-959-655.lbl
Part No SW: 5N0 959 655 A HW: 5N0 959 655 A
Component: J234__A01 VW10 HI 1815
Revision: 19013000 Serial number: 0039DP6ED1QO
Coding: 0012337
Shop #: WSC 06402 785 00200
VCID: 3B7E38C57A2630C68E5-806E
Subsystem 1 - Serial number: 6333FTS630380888
Subsystem 2 - Serial number: 6343FTS646120888
Subsystem 3 - Serial number: 6353ETS6DN12TVNH
Subsystem 4 - Serial number: 6363ETS64L02TVNH
Subsystem 5 - Serial number: 00000000000000000
Subsystem 6 - Serial number: 00000000000000000
1 Fault Found:
00003 - Control Module
014 - Defective - MIL ON
Freeze Frame:
Fault Status: 11101110
Fault Priority: 2
Fault Frequency: 254
Reset counter: 110
Mileage: 127760 km
Time Indication: 0
Date: 2000.00.00
------------------------
We ordered the replacement at the delaer, they supplied 5N0959655AA/00D
Of course we used several times the code 00D/0D to try to code the unit, using the workshopcode 12345 or the stored on the older unit. Also after this, we tried a lot of codes and all of them are rejected.
Can you help us or do you know why the unit can't be coded?
Address 15: Airbags Labels: 5N0-959-655.lbl
Part No SW: 5N0 959 655 AA HW: 5N0 959 655 AA
Component: J234__ VW10 HI 2518
Revision: 27019000 Serial number: 003L7P4CLA8P
Coding: 0000000
Shop #: WSC 00000 000 00000
VCID: 7CFCFBD93FA8F7DADF-8029
Subsystem 1 - Serial number: 6332MTS630380888
Subsystem 2 - Serial number: 6342MTS646120888
Subsystem 3 - Serial number: 6351HTS6DN12TVNH
Subsystem 4 - Serial number: 6361HTS64L02TVNH
Subsystem 5 - Serial number: 00000000000000000
Subsystem 6 - Serial number: 00000000000000000
1 Fault Found:
01042 - Control Module; Not Coded
000 - -
I hear some info, from now, Bentley require us program 02 keys at once.
Is it right or not ?
Last year i can program 01 key only.
Anyone know clearly, pls post here.
hi i need do new key for sprinter 2008 i think to get r270 black box to read ezs which version best 1.2 or 2.0? and to renew key and write MB IR PLUS any reviews? site the ezs is 9s12
I have a mondeo 2.0 140hp with a sid206, last year i bought a file to a member on Mhhauto, to remove dpf and egr.
I´m having some troubles with the car and I need a file only with dpf off, I need egr on can anyone help.
I know it's out there, there is a reatta enthusiast site that has it available for download but the webmaster demands name address and phone number before giving password for download. I'm not into giving away personal info to someone I don't know.
