It works against Clio II 2004 +, Sandero, Logan, Symbol (see immo box as attached file).
Use a eeprom programmer and read 93C66.
Read the file in hex or open it in hex editor.
The code is stored in "pair" in diffrent positions:
For clio Yahoo:
1st two digits, row 110 in column 13
2th two digits, row 170 in column 14
3th two digits, Row 190 in column 5
4th two digits, row 110 in column 12
5th two digits, row 190 in column 4
6th two digits, row 170 in column 13
For Clio II Auth full:
1st two digits, row 120 in column 7
2th two digits, row 180 in column 10
3th two digits, row 1A0 in column 7
4th two digits, row 120 in column 6
5th two digits, row 1A0 in column 6
6th two digits, row 180 in column 9
Now join the six pairs of numbers and you get the 12 digits
i know that u closed the thread for the startkeys and uploaded the keygen, but i need a good deeloper key to fix trhe order number in vitos and sprinters
i tried different keys and still the same, everytime i take a developer key from here, the order number dissappears
hi there ,
i d like some help with this activation ...My problem is when i install diagbox i get this message "the software cannot be activated error 0" i try everything with patches delete registry and install again diagbox , try to find the appdiag as scary said to delete it and reactive but i didn t find any of this file and all this in a fresh xp installation
p.s this isn t my first installation i ve installed a lot of this version , the problem began two weeks ago.
Here is the North American Operations version 32.005 software for Tech2 users.
Please show your appreciation by at least hitting the "Thanks" button and contributing to this site.
If little or no appreciation is shown, future software passwords will only be shared with contributing members via PM, so please friends lets help each other out.
I have Xentry 03/2011 v9.1.6
I have the developer keygen, and when I set the time of my laptop to 01/01/2010 and generate a key, that goes fine no problem.
But when I go run Xentry it says
Internal error (2.75)-3.175
I have searched and tried the ORIG files but still no luck, is it my date? what date should it be?
Car was involved in crash, is repaired and the module has been send to be cleared. Now the module does not respond to DAS at all. Checked that powersupply and CAN bus voltages are OK at the plug of the airbag module.
The guy who cleared the module told the garage holder that the module has to be programmed at the dealer.
I have cleared several older type airbag modules before. After cleaning I could put the module in the car and everything was ok without any programming.
Now I need your help:
1. Is programming for this module required after cleaning crash data?
2. Is it possible that the module will not communicate with DAS at all if the clearing has been done wrong?
3. Is a virgin file available so that I can fix this module?
The problem is that the interfaces are not always recognized by the computer. In the morning I turned on my notebook, I used the V117 CanClip program worked perfectly. Then I turned off the laptop and I did not recognize the interfaces, no connection was not detected. In vain I pulled out the usb cable to connect it again, not detected. 2 or 3 times and then I restarted the machine was good with great difficulty. But I always have this problem.
Why is this? If someone knows it, please help! Thank you very much in advance!
i have new ecu and 4d galss chip. i programming this car within t-code pro and it didn't programming the falsh code in dashbord light ...can help me and thanks
I am looking for update CD of Telematics for Mercedes W221 (2007) NTG3. Code of cd which I am searching is A2218277059.
Kind regards
Marcin
Hello Gents,
I would like to ask you something. I tried to update comand system through SD. I have new disc 2218270665_0001 which is for W221 (2007 year). But...Das/Xentry 03/2010 requests older disc (2218277059_0001) which I do not have. Is there some kind of afix for Das to use newer disc - 2218270665_0001 instead of older ones? I think that version of Das (03/2010) can be a problem, but I would like to avoid installing newer version of Das, cause this one works fine with me. Do you have an idea how can I resolve this problem?