I have a w205 with a dead MD1CP001 from which I've managed to read it on bench.
I want to clone it on donor ecu or immo off donor.
I’m looking for someone who can provide cloning service or to disable FBS4 on donor(immo off)
Of course I’m not asking for a free service, I want a tested solution.
Hello, I have peugeot 307SW 2005 with 95020 eeprom in cluster, and a JC BSI with a 95128 eeprom, managed to read cluster but having a problem with a BSI...Is cluster enough and can anyone help?
Have this A4 on the workshop and its impossible to enter on the vehicle settings menu. Already update the MMI to the last version available and the problem stay.
Have anyone face this issue and have managed to solve it?
Hi Im considering to buy new flashtools for both bench and obd. Currently using genuine dimsport newgenius and trasdata with e-gpt, but slave version, and have very little negative to speak of these tools, but looking to upgrade to master, so I've been looking at Kess3 and Autotuner, they can do many of the same ecu's as I see it. Doing a lot of VAG cars edc16-17, newer benz edc16-17+Delphi, volvo edc16-17, and some Volvo/ford with SID206/806. Does anyone have any experiences with any of these tools and wanna share pros/cons? I also read about FoxFlash but it seems its a cheap and low quality tool, which would be understandable comparing the price.
I have a fallowing problem with ISTA+ 4.39.20 standalone preacticated with full SPD. When I enter the vin without car connected to ISTA I get following error after starting the process. When I try to open any diagram or procedure I receive prompt the there is nothing to view. I used fresh vm with windows 10, c++ installed, java installed, regestry fixes applied. Any advice what to check?
Hi
Does anyone know why it can't activate Agilty mode on W221 mercedes. 7g 722.9 gearbox
I have seen many videos, when activated 211 212 204 mercedes with same 7g 722.9 gearbox.
But there is no video where w221 Agility is activated.Then when I googled, it was written that it can't activate
Hi
Does anyone know why it can't activate Agilty mode on W221 mercedes. 7g 722.9 gearbox
I have seen many videos, when activated 211 212 204 mercedes with same 7g 722.9 gearbox.
Hi all hoping someone can help me out and has maybe come across this problem before, I have a 2020 ford transit with sid212 with adblue sender problems, errors are
P206c
P206d
P206b
I ordered and fitted emulator and now have no fault codes but have error on dash for low adblue and countdown has went from 31 miles to 327 miles but is counting down when driving.
Adblue tank has been filled and still shows 20%, does anyone know if these emulators are capable of emulating tank level/quality or if level signal is analogue and if its possible to make level rise by placing resistance in level line?
Thanks
Hi I have a faulty MMT gearbox ECU. The " N" neutral inficator disapper because ECU is reset after learning. Please maybe somebody have " learned" dump from epprom 93a86. ECU AISIN. NR: 89530-12370. Foto label below. Od maybe similiar " learned" dump. Please help because the car start engine but gearbox not work. Thanks for advance
Original engine OM470LA.6-1-00 was completely damaged. Also MCM2.1 D3 Ecu (A 001 446 97 35 / 001, HW Num 0014469735001, SW Num 0354482035001) PCB was badly damaged. Engine was replaced with OM470LA.6-7-01. There was also used ecu coming with it: (A 001 446 62 35 / 002, HW Num 0014466235002, SW Num 0384481735001).
Used ecu cannot start the bus. There is immo issue. I was able to dump broken ecu eeprom and TC1797 flash. That content was stored to replacement ecu but it does not boot and even tester cannot connect (ecu in boot mode). So, sw is so different between those that programmable parts cannot work together.
What could be the best way to proceed? Could someone help to virginize replacement ecu original content so that it could be used directly?
Or could it be best to purhace used ecu with exactly same part number as broken ecu and put recovered files in that? Engines are not exactly same part number either. Could that cause new serios problem? Different charts? New faults popping up?
I have volvo with airbag internall fault.SRS-010E control module internal fault,Bought other used module,now get SRS-00D8 control.faulty signal SRS-0224 CANsignal:configuration fault and SRS-0230 switch for airbag passenger,signal too low/signal mising.
how I can exchange this unit?cloning?
