How to use V_ag Tacho 3.01+ Opel Immo Airbag scanner ?

could some one with the knowlage help me.....

i have a 2004 bmw 330d (204bhp manual) that has had a few mods and was remapped some time ago now on a dyno but ive now added more mods but need to use some of the currunt solinoids that used to control the swirl flaps to now control some think else, i need it to activate at idle 750rpm till 1500rpm then close.

is any one able to do this?

i also need the N75 map to work differnt... before it work by activating a solinoide to create boost pressure from the turbo but i now need to do the opposite and activate to stop it overboosting

is any one able to do this?

hello. I installed tecdoc on a virtual drive, and it works fine up to a point when I try to use the search function.




I have tried to install tecdoc on virtual machine win7 32bit and XP32bit, and on both on those occasions the same error occurs. and the program works properly when installed on win8 64bit (directly to system, not on wirtual machine.

Hi to everyone. I have a problem and need urgent help!

It's about combine John Deere 9560 WTS. When I turn ignition on, everything on Control Post is on (icons, but no light).

I have searched, and identified that problem is in flash memory (ST M29F040B-70K6) at cornerpost control unit. When I heat the flash, it works for a while and than stop again.

I read data from flash, and writed to another 29F040, but this time from AMD manufacture (AM29F040-70JI). When i solder new flash to board, nothing works - everything like before.

How can I know if data on flash memory is corrupted, how to fix that, or the best - can someone send data from that flash to me ?

Hi, can anybody help me with locating and deleting the EGR DTCs.
I'm quite new to this and cannot locate the code tables.

Many thanks, Hampton

Attached Files

EDC16C39-5.rar

86

63.79 KB

Download

pls is any one here idea of where i can buy original digi master3 pls should send me link
here.
thanks in advance

I would like to ask if anyone could help me with clearing crash data off on the dump from Toyota Yaris. ECU: 89170-52C00.

Attached Files

89170-52С00_crash.rar

43

273 bytes

Download

IKE imobiliser box 170 820 17 26

Imobiliser box has a 93c56 which I believe to be corrupt ,all FFFF

Has anyone a virgin dump for this please

Regards Eck

Hi all,
I'm searching for a full schematic of a PIWIS cable.

I've seen one here, but missing the pinout of the OBD2 side of the cable.

I do not need the electronic inside the OBD2 plug, because it's only for charging the KTS-650.
For KTS-520/550 it is not necessary to have the electronic.

Are anyone here who knows about the layout?

cheers

Ralf

i had a tuner mod this file for me to remove dpf , all is fine but emmisions is not right , its smoke test reading is 1.9 but the limit is 1.5 to pass the test . is there anything can be adjusted to fix ?

car is a 2008 saab 93 1.9 tid 180hp model

thanks

it wont let me attach the file,it says its not allowed ?
if anyone wants to take a look at it i can send it in email or tell me how to attach it properly

good here I leave the ECM TITANUIUM with 18,000 drivers.
Maps used to modify the ECU may increase power and improve performance

Attached Files

ECM TITANIUM.rar

2616

7.78 KB

Download

I need working software for xprog 5.50, i tryied install from chinacardiag but won't start on two laptops.
On winXP i had error.On win7 no error but still no starts.

W204 2.2cdi and ECU is Delphi
CRD.11 OM646 EVO
A 646 150 19 72
HW 50.06
SW 07.07
PD 07 M07
28103309
R0412C031D

Anyone can make dpf off and remove fault code in attachment photo ?
I read ecu with Ktag Please help with good file
Regards Plamen

Attached Files

MercedesW204.rar

232

1.78 MB

Download

i need a good winols to do my job...i have 4 winols...and all 4 does not work..

need a little advise on replacing a used 722.9 if I virgin the tcm and I don't have original tcm do I have to save the flow rates of the valve body befor I virgin the plate and then scn coding if so how do I save the flow rates I got fvdi and sd connect thanks

Hi maybe someone can do DPF off for edc17CP20 from crafter ?

Attached Files

EDC17CP20.rar

92

834.62 KB

Download

hi, all

Can anyone tell me how to set the vediamo control unit flash?

i need help.

thank you.

HI GUYS
I HAVE A SW DTC REMOVER 1.5.17 BUT NEED FOR CRACK , BECAUSE I DON'T HAVE THE KEY USB. CAN YOU HELP ME?
THANK YOU

need help in dpf off subaru forester 2.0d.
all interested thanks for the help.

Can anyone point me in the right direction please. I have searched but cannot find anything for this Vehicle.
We have an Ex Fleet Vauxhall Corsa 1.3CDTi 2008 with a 70MPH Speed Limiter.
Can this be done in ECU Flash/ Eprom or is it in BCM?

Hi folks. Never had this before. Ecu was replaced ,
How do i need to pair old key. Got ids kit and vag.
How to extract pin or god knows what do i need cheers.

hi my name is daniel I'm from valencia (Spain) I am new to this forum, I want to contribute my bit in this great forum with this software ecu bosch, excuse my English because I do not speak anything, I use google translator

Please Request Password at My PM (Private Message)

Attached Files

bosch ecu codici hw.rar

83

420.8 KB

Download

Hi all

I have a bosch mottonic M1.7 0261203484 i need an immo off as putting the engine in a range rover.

My docs say to program 27C256. is this a straight forward read and write or do i have to write on to a new chip etc? Thanks

Hello everyone. I'm looking for KIA Sorento 2,5 (2004y). crdi wiring diagram
Thanks in advence

Hi

Can someone remove P0030 O2 sensor fault from this file.

It is Corsa 1.3 cdti 2008.

regards

Attached Files

Original.rar

35

107.67 KB

Download