Hello
I have a problem
I change in customer car a mileage but now the trip and daily km is work
but the real km not move it show only what i edited
Can someone help me and tell me what to do???
The car is PEUGEOT 107 2005
eeprom 93C56 i read x16
I have a BMW E38 Sports M tech 740I M60 B40 V8 with a bosch 0261203484 ECU. i believe it has EWS11 i need to bypass this as its been put in to a range rover. attached is full read from chip. Can anyone help.
do i need to buy a 404 dme and cutt pin 66 or can i burn to this chip? Thanks
Version : 2014.10.0.1
Developer : Infomedia
Language : Multilingual
Description : spare parts catalog Land Rover Microcat contains information on spare parts for the legendary Land Rover brands and Range Rover, once part of Rover Group. catalog of parts for all models of Land Rover (1986 - 2014 years).
It takes time to upload and only 3 sec to press thanks and Rep +1 to show your appreciation.
That will give me more mental energy to upload more stuff for you all
I have w210 e200 petrol 1998 year my ezs and eis lock are dead what should i do i found locks and key from another w210 i need to virginize the ecu ande code with das or there is another procedure.
Thanks in advance.
I want to change the fuel filter, on previous models I've seen them behind the front wheel liner and also in front of rear wheel by fuel tank. anyone done this can let me know before I start removing unnecessary trim?
also, understand it remains pressurised and needs priming before use. any tips for this?
hello I would like to clear the DTC P1305 from the map punto evo 1.3 mjtd, ECU Marelli 8F2. is there anyone who can help me, thank you in advance hello
Trying to reset an SRS light for 2005 Saab 9-3 without success. Car involve in front end accident. Driver side airbag deployed. Replace airbag, seat belt tensioner, and reset airbag module. Here's what I did to try to clear the code. Please let me know if I'm missing anything.
1.Select year and model car
2.Read DTC
3.Clear DTC
4.No success, airbag light is still on
I also try replace with a different airbag module (known good module without crash data) and when I try to add it with Tech2. I get a message something about Configuration can only be made once or something like that followed by a FAILED message.
pls anyone help me with immo off eeprom file for peugeot 206
sagem ecu
HOM:s2000-2A
3098711962
eepprom :95080
i damage my eeprom on trying to unsolder it, so i do not have file
I'd like to check this problem out myself before going the expensive route and purchasing a new ECU. When the car just died I easily narrowed it down to the ecu fuse. Replaced the blown fuse and the car tried to start but instantly blew again. Against my better judgment and because I was in an intersection under construction I used a paper clip hoping to just get the car over and parked. WOW, burned the paper clip in half. I'd like to at least check for loose wiring but don't have a clue where the ecu is even located. Any help or suggestions would be greatly appreciated.
Version : 08.2014
Developer : INFOMEDIA
Language : Multilingual
Description : Catalogue of spare parts and components for cars, vans FORD trucks and American market.
It takes time to upload and only 3 sec to press thanks and Rep +1 to show your appreciation.
That will give me more mental energy to upload more stuff for you all
Good day!
A small gift for mhhauto users!)
DIY (homemade) Injector Cleaner PC-based Station.
What you get :
- Software for PC
- Scheme of adapter
- Fuel Injector Balance Calculator : 2, 3, 4, 5, 6, 8, 10, 12 -cyl
- Help Injector Flow Table
- Help Injector Parts
- Help Use Software (picture)
I do not know who the author of this wonderful program and I do not remember where I downloaded it ...
But this program deserves to be in the collection of your PC!
The program is in Russian language ... Stop! Don't panic! )))
Just a few buttons and a few minutes to see how it works ...)))
However, do not use it only for cleaning injectors ...
Adapter on transistor IRFP064N - practically "immortal" - that will allow you to use it in different control schemes.
Turn fantasy ... You can check the solenoid valve, fuel pumps pulsating type of auxiliary heater, relay, ignition coil and still something else ...)))
See for yourself!
Best regards,
Dmitry
EDIT #1 : Link was updated. Reason : diagram of adapter was modified.
Please, re-download file.
EDIT #2 : Link was removed. Reason : added english version of software. See post #4.
Hello everyone,i need help with bootpin for two ECU:
----DME MSV80
----DME MSD81
I try to read with galleto but,I can not find the boot in the documentation.
Using E-Sys i had a problems, more then few time of not having CAFD files
So today i decided to Join version v51.3 v53.0.5 v53.4 v54
For a comparison for a future beginning users so that there wouldn't be any disappointments during E-Sys Sessions
As you will see from attachemts that sizes are from 30GB-40GB
Since one version is missing something and another version is missing something else
But once all of the above been joint it show about 80GB, that makes me think that complete PSdZData should be around 100-140GB keep that in mind for a future use of E-Sys
I need to extract pin code(s) for a
Audi A6 Avant Quattro 2.5 TDI motor code AKE.
I have a SuperVAG tester.
For the pin code extraction it gives 3 options:
1) Cluster
2) Immo-box
3) ECU
I've tried Immo-box but it gives me "error"
For the ECU option it gives me the pin for the EDC 15x option. But curiously it gives me also information such as chassis number and others also for the "Me 7.x.x" ECU option that it seems to me is an ECU for petrol motors. Really do not know how to explain it.
I've not tried the Cluster option.
Do you know if this car has all these three pins or how many?
Adresse 44: Direction assistée Labels: 1KX-909-14X-44.CLB
No. VAG du calculateur: 1K1 909 144 G
Pièce et/ou version: EPS_ZFLS Kl.0 1401
Codage logiciel:
Code atelier: WSC 00000 000 00000
VCID: 2F670649C78D
2 faults:
02546 - Stop limit executive
005 - Basic / non-existent or incorrect adaptation...
Transmitter steering angle (G85)
014 - Faulty / defective (s)
i follow the procedure but doesn't work the light still on (orange color not red color)
[Select]
[44 - Steering Assist]
[Coding-II - 11] or if that function is not available then use [Sec.Access - 16] instead
Enter 40168, to enable the basic setting.
[Do it!]
[Basic Settings - 04]
Group 060
[Go!]
Activate the Basic Setting.
[ON/OFF/Next]
After a successful basic setting, field 1 should say "OK".
[Done, Go Back]
To make sure the basic setting was successful, check the sensor again.
[Measuring Blocks - 08]
Group 007
[Go!]
Check field 1, the value has to be between -1.5 and +1.5 °.
[Done, Go Back]
[Close Controller, Go Back - 06]
Note: After successful basic setting, the Steering Limit Stop needs to be adapted too.
and these;;;;;;;;;
Steering Limit Stop Adaptation
(Engine still running)
Center steering wheel (±10°) and hold it centered for 5 seconds.
Turn steering wheel completely to the left and hold it there for 10 seconds.
Turn steering wheel completely to the right and hold it there for 10 seconds.
Center steering wheel (±10°).
Switch OFF engine and ignition.
Switch ON ignition.
Wait 5 seconds.
Steering Assist Warning Lamp should turn OFF. If it doesn't, perform a short test drive.
please i need help
thanks in advance.......
![[Image: 14ab3408a8bb0a46e2cc2e8f28dbd9b0.jpg]](http://i68.fastpic.ru/big/2014/1024/b0/14ab3408a8bb0a46e2cc2e8f28dbd9b0.jpg)
