Hi,
i need help with eeprom , c-max 1.6 hdi 2008 year
after programming starts to enter into limp mode and showing p1187 fault,
I use bdm to read write,
Problems looks like that, if you turn ignition 1 time, it shows the motor defect fault on instrument, and in ecu p1187 is shown, but if you turn ignition of and on again, then you can use the car as normal, no fault code are found,
Summary: it is always happened after3 minutes ignition is off,
but twice turn ignition on and off, and everythings works fine,
The eeprom is attached,
Can anyone check or repair dump.
Thanks,
Slawo
Having an issue with a 986 Boxster S 3.2 M96/21 Engine 2001 Model.
Starts in the morning fine, drive it until it gets to temp or let it idle until it gets to temp and it will die and not restart. I have changed the fuel pump as initially in this state on crank and ignition live there was no fuel pressure at the rail.
Anyway the same is still happening, when in dead mode it will not produce fuel pressure at the rail unless you manually operate the relay, but still it won't start even when fueling.
I've checked both engine management relays which are fine and have even swapped them out just to eliminate.
Any ideas guys?
I cant see on a wiring diagram any reason that the relay would not operate and again even when I bypass it I just get a crank and no start.
Order Parts for your Bosch working Tool easily with the Bosch Service DVD 07.2014
Include Part and repair Information for:
Bosch
Skil
DREMEL
ATCO
Qualcast
Suffolk Punch
Roto zip
CST/berger
Push Button Thanks & Rep+1 = Helping and support from me
Hello,
I have a Mazda 5 2L Diesel 2007, It come with this code first,
P0133 - Heated o2 sensor circuit slow response
once I cleared it and took for a drive it reappeared.
Then I cleared it the last time and took for a drive the dpf light started flashing, when I read codes it was below one only.
P0234 - Engine overboost condition
Once light on its down on power, then switch off and on again it goes fine no light on.
Would you have any reading for these codes? Or any ideas.
I fitted a universal o2 sensor at start. but didn't make a difference.
RENAULT Dialogys v4.34 - FULL ENGLISH Spare Parts and Manuals
Dialogys - an electronic version of documentation for RENAULT and after sales car RENAULT, DACIA.
Dialogys includes everything from repair manuals and parts catalogs for all models of cars Renault
EPC Section (Spare Parts) = MULTILANGUAGE
Technical Information & Repair Manuals = FULL ENGLISH (GB)
Version: 4.34
Compatibility with Vista/Win7/Win8,8.1
If you have a previous version , you do not need to install DVD0 - application disk , because it is still the same from version 4.18.
the VIN decode in Dialogys is made through A2A server, which only Renault representatives have - software which connect to Renault servers through certificate. Dialogys connect to A2A , which ask Renault servers and then back to Dialogys. Every version of dialogys can decode if it has a "trusted" (authenticated) connection to A2A server.
1992 Camry LE, 2.2, automatic
I installed a new timing belt, water pump and tensioner pulley. I checked the belt several times by turning over the crank 2 times. Everything looked good with the cam timing marks. I did several more revolutions and checks and all was good.
I put on the lower TC cover to make sure I could see the crank mark at zero.
I left the alternator off the car and did not refill the coolant yet.
I put in the spark plugs and attempted to fire it up. It started and ran smooth at idle for about 25 seconds. I then gave it some gas and it died. I was satified enough to bolt on all the components including the alternator. I attempted to start it and no go. I looked at the crank and timing marks again and they are good. I tested for spark and lo and behold, no spark. It just cranks and I can smell gas.
Questions:
Did I burn out the ignition coil by running directly from the battery with no alternator installed.
Is there some other relay or fuse that I should be looking for with no spark.
There is no crank sensor on the 1992s from what I've read.
Tomorrow I intend to pull the distributor and check the coil. I would think that even if the timing belt slipped a tooth or so, I would still have spark.
Thanks
06 sportsman speedometer isn't showing my speed or high low reverse or park
--------------------------------------------------------------------------
Enterprises need to play a key role in technological innovation .An
good auto scan tool could help you
save much money
I try move eprom 24c16 original eps in seconde hand eps surprize is naw can t diagnostic eps with tool clip.can virgin bin power steering second hand.i put in attach bin .thanks
hi all member
i have a clear airbag for renault megane classic 2001 dump file autoliv 600 63 94 00 its good for me
but the dump have a airbag In the rear seats
But the car did not contain them
And now I want a picture shema for calculator airbag In order to delete it
any help please
hello,i have unlocked my SG. cr6eu5 : FN_SG_Entriegeln und AGR. off not installed coded
but it will not Explizit_restricted , just Explizit_unrestricted.
what can i do to get the command ?
HELP!!!
I have a 2007 fiat ducato that requires immo off
I have bdm100 but my software only allows partial read (597kb)
Is there any other software available like 555 pro/ transdata etc
Or does anyone have 555 pro? Willing to pay
![[Image: postbit_thx.gif]](http://mhhauto.com/images/postbit_thx.gif)
![[Image: postbit_reputation.gif]](http://mhhauto.com/images/english/postbit_reputation.gif)
