I used a super vag 2 for odometer correction for vw caddy 2004.
it read correct mileage but when I tried to change it said 'error' ..
then I used my x-tool (should have used it the first time), it also read correct mileage (dash+ecu) but when I tried to change mileage in dash it also said error..
is it possible that the super vag blocked anything in the odometer?
or might there be another explanation why both tools give error when tried to write mileage?
(mileage was changed before of this car, because I saw ecu had stored a higher mileage then dash).
So i was thinking these days to make a full pack at day regarding the the firmware our CDP+ interfaces.
As you all know we can flash our interface SAFE only inside Delphi 2012.3 (last version without clone blacklist) or in these days inside WOW (no matter what version).
We (at least me) prefer to write the firmware with WOW because like this i can use wow and delphi-autocom without problems since WOW writes some extra bits that delphi-autocom does not detect but wow does.
Story short, what will you find inside this pack: 1. Mprog 3.5 and ept file for CDP+ (never seen one that has this problem) 2. How to recover your CDP+ from a bad flash or red lights problem via USB. 3. How to read your firmware with a ST-Link device via CDP+ J400 connector and also pinout of STLink to J400 4. How to read the OTP (One Time Programming) area responsable for the serial number of your interface - BE CAREFUL . This area can be modified only by incrementing the actual serial number in the already written ST chip or you can write any number in a new one if you know how. 5. Flash Loader Demonstrator v2.6.0 to restore your firmware via USB 6. STM32 ST-Link Utility v3.4.0 to read firmware and otp and if you are willing to risk to change them. 6.OTP area for CDP+ Clone 100251 bin file. 7. Firmware from programs: 1321 from WOW ;1331 from delphi, autocom, wow; 1410 from WOW, 1422 from Delphi and 1423 from Autocom. 8. Firmware recovery to flash your CDP+ interface in case of upgrade or bad flash:
a) Old ones already on web:2012.2; 2012.3; 2013.1; 2013.2.1; 2013.2.2; 2013.3. b) My flash files written to CDP+ by WOW and read via ST-Link saved as .bin,.hex,.s19,.srec from my clone CDP+ FOR RECOVERY
2013.3 - Firmware 1331
2014.1 - Firmware 1410
2014.2 - Firmware 1422 from Delphi
2014.2 - Firmware 1423 from Autocom 9.24.12.2014 Firmware 1430 from Autocom 2014 R3 2.14.3
10.24.12.2014 New pack with RECOVERY FIRMWARE 1430 .bin,.hex,.s19,.srec included and all from 1->9
If you find something wrong or to add to this pack please write.
All you need to play with your CDP+ interface it's a ST-Link V2 Programmer CLONE like these HERE or the Original.
P.S. For those who have problems downloading from MEGA you have HERE independent mega downloader portable.
If you need a password for a file, like always it's fantomel
11. - 12.04.2015 - Added to MY COLLECTION for CDP and CDP+ Firmware 1513 from AUTOCOM 2015 R1 2.15.1
12. - 12.04.2015 - Added MY COLLECTION for CDP and CDP+ where you will find all above + Complete Install kits to Delphi and Autocom 2013.3 , All my WOW 4 and 5 Collection, All Genuine Kits of 2014 and also The mixed 2014.1 Version with 2 patches(one already present in main archive and another one separated) - a little late but i forgot to post this also here.
13. - 20.04.2015 - Added to MY COLLECTION for CDP and CDP+ Firmware 1424 and 1430 from Wurth Group for WOW and W.EASY 14. - 07.05.2015 - Added to MY COLLECTION for CDP and CDP+ Firmware 1515 from Wurth Group for WOW and W.EASY 15. - 24.08.2015 - Added to MY COLLECTION for CDP and CDP+ Firmware 1520 from Delphi R2 2.15.2 16. - 20.09.2015 - Added to MY COLLECTION for CDP and CDP+ Firmware 1521 from W.Easy WOW 17. - 28.12.2015 - Added to MY COLLECTION for CDP and CDP+ Firmware 1532 from Autocom/Delphi 2016.0 18. - 16.02.2016 - Added to MY COLLECTION for CDP and CDP+ Firmware 1532 from W.Easy WOW 19. - 05.04.2016 - Added to MY COLLECTION for CDP and CDP+ Firmware 1534 & 1535 from W.Easy WOW 20. - 03.06.2016 - Added to MY COLLECTION for CDP and CDP+ Firmware 1612 from Autocom/Delphi 2016.10 21. - 08.08.2016 - Added to MY COLLECTION for CDP and CDP+ Firmware 1615 from W.Easy WOW 22. - 15.10.2016 - Added to MY COLLECTION for CDP and CDP+ Firmware 1622 from W.Easy WOW and Autocom 2016.20 - Last fw for CDP interface since from 11.2016 is EOL
Hello, I have an a problem with Acura RDX, the car was water damaged and the ecu and the immo (from ignition barrel) was from different cars as well as the instrument cluster and the body control module. The long story sort, I cannot make this car running as the ecu and the immo is from different cars so I do need paired dumps to make the transponder for it and get the car started. Please see the attached picture with the eeprom dumps from ECU (37820-RWC-A57 KEIHIN) and the dump from immo box (39730-STK-A010-M1 VALEO). Any help will be appreciated. Thank You in advance.
drying to read S1000RR ecu BMSK ME9+ with kess clone. i have ori cable but when press OK to ID or Read, nothing happens. It shows battery voltage correctly. Any Ideas?
Tried to calculate by my self with some calculator but no luck.
If somebody generious could give me a code?
BP 7643301316
Fiat 156 053 469
BP 330158351581
Hi,
Firstly I erase the DTC's from ECU, then set the counter of DPF to 0 and finally get the ECU on table.
Read it by BDM, then make a switch solution :
The DTC from FAP is gone, Check Engine diode is gone, the sensors are plugged in, all reading are OK and there is no limp mode.
The problem is that ECU goes in the regeneration mode (white/grey smoke like too much petrol is injected).
I also get EGR off and it seems that solution (2 maps 12x1) works perfectly.
Could any one give me some help/hint what is needed to do more on this one ?
help. when encoding key with VAGdashCAN V5.17 now 25. I do not get no immobilizer inmo channel 25. I get the car is a audi a3 8p. someone has been the same.
), it also read correct mileage (dash+ecu) but when I tried to change mileage in dash it also said error.. 
