Please Immo off.....

I try the vediamo 4 ，5 in Xentry Connect. But it can not recognize the Xentry Connect.Does anybody know the method to use Vediamo in Xentry Connect hardware.

can anybody switch off egr and swirl flaps o remove DTC P2008? Thank you

TRICORE_BOSCHMEDC17
Bosch EDC17CP20 external flash VAG
1037502339
03L906022NN 5070

Attached Files

a 4 ditone .ori dim.rar

87

491 bytes

Download

hi,

has somebody the xprog 5.50 software inside vmware, virtualbox or virtual pc that works well with xprog 5.50 clone?

thanks in advance

hello all member please you help me clear crash nissan frontier 98820ZL70A

Hi,
What do you think, guys? If I will publish Chrysler Vehicle communications - student guide here?
118 pages

Hi. I needed to read ecu flash on Mercedes E200 W210) with KWP2000+.

After I click Read Data software shows error, fan (front radiator) start spinning at high speed on ignition and now car cranking but won't start.

ECU Bosch 0 281 001 819 (EDC15C0)

Solution ? How to reflash it again if I dont have original file ?

Radio code volvo S40 HU-615
serial v03490 34W349R/RY-615-2AS
MODEL 34W349R/RY
radio in Of

HI evry body i need ful bdm CMD dimsport or fgtech for this audi A3 140 ps
hw 0281011847
audi 03G906016BA 7000
thanks for all

Hyundai GDS 04.2012 Full Multilanguage

Attached Files

Hyundai GDS [04.2012] Full Multilanguage.rar

160

3.63 KB

Download

help please guys ineed your i,v Steering is heavy and lamp ESP but no fault code mercedes w204

Hello, I have a problem with a TV tuner original Mercedes A2219006102, mounted in an ML W164 comand with NTG2.5. I run the wizard to update the software, I entered "the CD telematics" in the comand system stardiagnosi richiesto.Ho used as the DAS 9/2011 version, the upgrade process is successful, but at the time of restart optic ring the DAS system has shut down unexpectedly. From that moment I was given the opportunity to re-run the firmware update of the TV tuner. Now the software version of the TV tuner is displayed "wrong software", I tried to run the setup with Das 1/2014, but do not run the commissioning of the unit. The unit worked perfectly before upgrading the firmware .
Now when I connect to the PC using the mini usb is recognized as TV tuner, requires drivers to install, but do not know if it's possible to flash the firmware via PC. The chip inside is Spartan6.
   

hi to all
i need xprog pinout for bsi valeo 2004 p07.00
thanks in advance

Hi,

can you help me immo off this ECU (24c02 memory). Known programs doesn't work ;( I'm starting to think that this ECU is broken.

Seat IBIZA 2000, BOSCH 038906018FB 0281010006

Attached Files

24C02_ori.zip

224

255 bytes

Download

hi
i need virgin dump for mercedes spriter 315cdi
thanks

Attached Files

0281015254.rar

50

363.27 KB

Download

hello everybody..

searching a original k-tag from alientech slave or master in used condition for a good price...

if anyone have one, pls write me pm

thanx
br

Hello folks i drive that car but not run to fast and consumation (city) are 16/100
After remap will have a change and what?
Thats the ecu but its not possible to open it ... i have williem programer only .

need immo off siemen ecu 2 plug eep 93c76 many thx tried with avdi but still not start enc both files thx

Attached Files

fabia immo.rar

27

1.22 KB

Download

Guide to repair the Toyota error code P1300/14.
Toyota Error Code: DTC P1300/14
Description: Igniter Circuit Malfunction

Probable causes:
1. Camshaft position sensor connector detached.
2. Camshaft position sensor failure.
3. Wiring.
4. ECM.

Do the following:
1. Check spark plug
2. Check for open and short in harness and connector in IGF signal circuit between
ECM and igniter
3. Disconnect igniter connector and check voltage between terminal IGF of ECM
connector and body ground.
4. Check for open and short in harness and connector in IGT1 – 3 signal circuit
between ECM and igniter
5. Check voltage between terminals IGT1 – 3 of ECM connector and body ground.
6. Disconnect igniter connector and check voltage between terminals IGT1 – 3 of
ECM connector and body ground.
8. Check for open and short in harness and connector between ignition switch and
ignition coil, ignition coil and igniter
9. Check ignition coil
10. Check and replace ECM

Techstream ECU Reflash programming guide.

Attached Files

ECU reflash.rar

488

3.42 MB

Download

Hi,
Someone Is able to activate the software for FVDI are unlocked and work with him, if successful, let show you how it works and what generators used.
Thanks

The program writes the images to the memory card diagnostic Tech2 device via comport.
No need to remove the card the way the card is written through com port.
I have not tested the efficiency of the program but I think it works.
No pass---- FREE

Don't forget to leave +rep and thanks if this helps you

Attached Files

cardwriter.txt

437

73 bytes

Download

Can somebody help by retrieving a pin on this cluster. The old one crashed and the car was brought to me without an old cluster. Please.

Hi, Does anyone have keygen or can reactivate my Actia multi-aid diagnostic software.
Thanks in advance for any help.

SELLING ACTIVATIONS FOR DELPHI 2014.1,£30 EACH FILE, LINKS TO SOFTWARE AND ALL YOU NEED FOR COMPLETE INSTALLATION AVAILABLE FREE,PM FOR EMAIL ADDRESS

Attached Files

Thumbnail(s)
   

hi guys,

mine cousin has a Merc ML 320 cdi of 2006 but he got a SRS error on the dashboard en i looked with delphi VCI and give me 2 specific fault code but dont i know what it can be the fault code are:

92B0 and 92D0 what are the issues and what can i do to fix it

thanx in advanced

Hello ..
Is there a possibility to change the milage on a Mazda 626 ?

Thanks


Sorry .. Translated by Google

Hi

I am using the MPPS 13.02 China clone on a Smart FourTwo 0.8 CDI edc16cp32.

When i want to read the ecu, it says that it is locked... Do anybody know how to solve this? Is it because of a cheap clone, or why is it not possible to read the ecu? I can only check ECU ID.

Regards
Mike

hello friends,

anyone can help me? I need to know what the error code means ah4031 a Fiat EU15

thanks in advance