I have here a Audi A4 2003 Petrol 1.8L Turbo
Engine Code: BLF
The TCU is made by Temic :
• HW: 01J 927 156 HT
• SW: 8E0 910 156 L V30 01J 1.8L 5VT RDW3251
Anyone maybe have original or newer File 8E0 910 156 L in SGO format for this TCU?
This a set of links to MEGA of -=Installer for Alldata and MOD=-
It covers:
AllData3Q2013 ( Portable Install )
AllData3Q2013 (Full Install )
Mitchell OnDemand ( Full Install ) it works on 2014
Mitchell OnDemand ( portable ) it works on 2014
I am new to the electronic side of things.
I was hoping someone could send me instructions for dummies on how to extract a dump file from vcds 12.12.2 cable(Chinese clone).
I want to share the software and cable dumps.
Hello. Today i buy R270+ black box and everything is ok. I put 35080vp and erase and my tool erase ok i choose program and device say wait 1-3 minutes and in adapter eeprom red led is not working and i wait 10-20 min and light not go on. Can anybody tell how to repair this adapter or my tool is broken?
My goal is to virginize BMW/MBZ and maybe even some variety of Nissan/Infiniti (but for the most part I will stick to those two german cars), so what do you recommend that can virginize or at least copy the information over?
I'd like to learn how to do this myself -- you know what they say about teaching a man how to fish.....
Thanks fellas!
PS: My budget isn't that large (yet) so I can't afford to spent thousands on quality programmers, so what do you recommend as a starter?
I've checked the language settings in the registry (0409) and removed and reinstalled SDNC - still the device is showing up CHinese. I know it probably doesn't matter but I remember there's a function where I can power it off but I can't read the thing to tell. Any tricks to get the device in English?
hi, i have a digiprog clone.. i tried to do a mercedes 2004 w203 today and it said use plug st49 but it dose not say in the manual how to use st49 or where to connect it to, has any one had this problem and found a solution? many thanks in advance..
hi folks, i have a cls with a fault on the dash saying suspension malfunction visit workshop, i had it plugged into a star diagnostic computer and in came up with fault code 5507 "suspension strut plausible" has any one any ideas? or had this problem?? many thanks in advance...
I would like to ask you, which computer/notebook do you have best experience with ?
I mean , brand, model, cpu, or specific configuration.
Scope of use :
Basic diagnostic for VW group, BMW, Mercedes, French cars, Japan cars…
hy ,i have a question, (i'm new here....) ,i wan't to buy a mpps cable with software to do immo off and egr off and etc... ,what is de difference between MPPS V13.02 Auto ECU Chip Tuning Tool <<AND>> SMPS MPPS V5 Tuning Remap Chiptuning K+CAN Flasher Cable??? or what do you recommand me to buy..
[attachment=53622]could someone look my tune over to see if every thing is good or maby some ajusment tips this is on a 2009 duramax lmm engine dsp5 efilive tune with five setings thanks
I have here A4 170 PS 03G906018AQ Siemens PPD 1.3 with DPF problem. Car was in limp mode and lights where on on dash (MIL and yellow heater) and on FIS also.
First I was try to read it with MPPS and do it with Volta but MPPS did not want to write file back and I have DEAD car.
OF COURSE MMPS DO NOT READ GOOD BACKUP and I stuck with non runner.
Than I find BDM file from same car like mine and write it trough BDM and now I have good starter/runner.
Now there is no any MIL lamps on dash exept on FIS
Can someone help me here to disable this DPF totaly please but not with Volta or Ecuscan ( I don't want to do same procedure after 100-2000 miles)?
Thanks in advance
Best regards
P.S. If you have car like mine do not try to write any file with MPPS or you are gonna ended with dead car!!!
The Data Smart 3+ is a hand-held multi-function programmer for digital odometers, airbag modules, car radios and car immobilizers. Powered by two CORTEX ARM cores, speeds up to 200MHZ., With a SD card interface to load and save files, USB port for updating by the Internet, 320*240 TFT LCD with 256K colors to show pictures and help files in great detail. With integrated CAN-BUS / J1850 / CCD-BUS / ISO9141 / SPI protocols in one multifunctional interface.
Self-test function integrated within the system.Advanced operation environment, by extended menu and picture guidance.Integrated data backup function to enable safe working procedures.Log-file function integrated in to software ; this will be a step forward in the tools operation and development.Hex editor integrated into software. Advanced security integrated into hardware.
Standard Package
Main Hardware: OBD cables, EEPROM adapter, MOTOROLA adapter, BENZ-38 connector, BWM-20 connector, clips, touch-holders, USB cable, Power cables, with standard software.
Software: OBD functions are active without USA cars; OBD airbag functions are active for VW, AUDI, SAIL, BENZ, BMW, OPEL, FORD, GM
