i NEED TO CHAINGE KESSY so i need old and new kessy(used)
pin if you can decode.
Or mayby is other wai to swap kessy maiby bi soldering eproms from one to other kessy?
For anyone who needed the "JLR SDD 138, SPA, VDF_L, VDF-J+Patch "
its on torrent , Fulljoy it.
[attachment=48744]
Install SDD DVD138 Full.exe and RESTART PC then install updates, then restart PC, then install VDF_L, VDF_J and restart PC , then install SPA DVD138_V2 .exe, then restart PC, then run the "JLRPatch_EN.exe"
Note that "EN" stand for English language.
NO PSSWRD
[attachment=53776]
........................
Hi I have a Renault clip clone. When I connect to my top usb port I get the green ISO light on but not the CAN light on. When I connect to my bottom usb port I get the green CAN light on but not the ISO. I can't get both on together so can't connect. Can anyone please help me? Thanks
Dear friends. Just bought this car with one key (without remote) and want to add second one as a spare. Already got key with blank transponder. I'd also like to change mileage via OBD. I tried to read PIN with VAG Commander different versions with no luck (maybe it's my cables). Only reads some old cars. So my question is how to read (which software you recommend) the PIN code for coding new key?
Maybe:
-Digimaster but is too expensive for me and mileage only?;
-Digiprog mileage only?;
-VAG Tacho;
-what you think about Carprog or do you recommend any other tools which can do both?
It would be great if it could do Golf V, Passat b6 (mainly mileage), T5, some Audi's, Skoda etc.
Thanks!
Please Help me
I have Laptop lenovo and Programe DAS & Xentry Version 11_2012
and Multiplixer C3
yesterday The program DAS & Xentry & Diagnosis C3 Work 100%
today Diagosis not accesible from DAS & Xentry
USB connect OK com port4
What is the solution to restore the correct connection and accesible
Hi I got the car in the Workshop Corsa D 2011-2012
Orginal airbag ecu was lost by body shop so owner bought brand new ecu from dealer.
The problem is I coded Can Low and Vin but when I try to do variant coding for sdm
It dosn't accept it at all In Op-com there is option to enter the coding hex value, it dosnt matter what options I choose Op-com alawys codes the same hex value to the module which is 0xFFF03A80, I manged to work out which number is responsible for left or right hand drive steering wheel when I enter 0xFFF03A91 it accepts the coding and I can see that ecu now is coded for Right hand Drive vehicle which it should be but. I have to disable curtain because this car dosn't have them. Does any info on this or there is special procedure to code it :/ I tried Launch x431 but it only can code chime in the seat belt.
Maybe someone have adblue bypass for newholland tractors, combines? Or maybe you could get me on track how the bypass should work? I have all schematics etc. There are a lot of different chinese bypasses but I don't think they work, right?
Done this many times but loaded delphi 2013.3 on to an XP SP3 laptop with net framework 3.5 and ran with delphi "new vci" recodnised as a DS100. all good and working for 2 weeks.
one day turn off and back on and all of a sudden it does not recognise the VCI. When searching COM port it finds it "DS100" when you go to test it says the vci is not connected or to update firmware which wont work either.
Removed Delphi and re installed. same with drivers. No joy.
tried the VCI on my own computer running 2013.3 and works ok. tried my VCI on the computer and wont work.
Could someone please help, I am running clip v135 and have Renault pin extractor, firstly I have no problem doing the card procedure up to 2005 cars, 2006 on seem to have a different imo box (siemens)however I can still get the pincode no problem, during the card allocation procedure everything goes well up to the point where I get the key code which I then put into pin extractor and it generates the pin to proceed to card allocation stage, this works fine but as soon as I hit next it comes up ''EXECUTION CONDITIONS UNSATISFACTORY'' Can someone please help me with this??
I am playing around with Vediamo 5.0.4 on a Windows 7 32 bit Laptop.
I read a couple of posts where people write that it's running with a SDConnect Multiplexer via WLAN.
My MUX is connected to power supply, I created a Road24h network and connected MUX and PC via an Adhoc network.
When I click on Update in the Vediamo Server Caesar Window I get a couple of settings and I tried all, but no luck. The connected MUX should appear in this Caesar box, right ?
I also tried via cable but alsono connection
Could anybody share his configuration how to get this connected ?
I know that I can use this device to update the modules on many cars as I have done this before.
I know that Drew Technologies has their j2534 Toolbox for the Mongoose cables and the Cardaq's. I am wondering if there is a similar software out there that will give you similar features with the OTC j2534 device.
Hello !!
I have a Fiat immo box (see photo in attach)!!
It has 93c46 eeprom inside.!!
I read it, and my dump, is in attach!! Please I need a virgin file!!!
Thank you!!
hi guys i have a "SW" new generation to read pin code for all of you my friends
Code:
Special function PIN calculator
Nissan/Infiniti PIN calculator
Description: Calculate PIN by BCM part number.
Ford/Mazda incode calculator
Description: Calculate incode by outcode.(Before 2012MY)
Honda/Acura password calculator
Description: 1st password, 2nd password, HIM unlock password, PCM code for any year.
>>> M8's!!Only Click here to download <<< Notes:
language is chinese!
do not forget to click on the buttons and this Please do not ask for PASSWORD on the thread / post / forum (ONLY BY= 'PRIVATE MESSAGE') best regards ?????
![[Image: s71.gif]](http://imageshack.com/a/img844/3368/s71.gif)
![[Image: postbit_thx.gif]](http://mhhauto.com/images/postbit_thx.gif)
this ![[Image: postbit_reputation.gif]](http://mhhauto.com/images/english/postbit_reputation.gif)
![[Image: learen.gif]](http://garage-automotive.com/images/smilies/learen.gif)
![[Image: postbit_pm.gif]](http://mhhauto.com/images/english/postbit_pm.gif)
