Anyone out there with a hq autocom cdp managed to get it to talk with a Citroen C1 airbag ecu using a software version newer than 2011 release 1?
When i bought my autocom it came with 2011 release 1, never had a problem with it reading all my cars ecu's. 2011 release 1 didnt have the iss feature like later versions for my Citroen C1. I noticed after upgrading to 2011 release 3, the new added iss feature for my car, it would then read all ecu's except for my airbag ecu. Went back to 2011 release 1 and not a problem would communicate with all of them including my airbag ecu. I have now upgraded to 2012 release 1+2 with thanks to blacktoy for activating my xml file in the hope that I would now be able to communicate with my C1 airbag ecu, but unfortunately not, same problem as 2011 release 3.
Anyone out there managed to try this to see if they have the same problem.

have someone Infos about the Xentry TAB Tablet Diagnose Computer ?
It will run Xentry on Windows 7 ?
is it possible than, that Xenty can be installed on Windows 7 directly, without an VMware tool ?

how had some Infos about it ?

Where can I download one of these old and golden DAS versions like 2008, 2010...?

thanks
silomon

I bought a universal programmer WELLON VP-390 and I want to read 29F200BC from the ECU RF5D DENSO (Mazda6 136HP).
After desoldering eprom from ECU I soldered to uniwersal adapter then tried read but programmer reports wrong connection on pins 1 and 3 (address bus) so the chip is impossible to read.
I checked all the connections, everything is ok.
I tried read other chips - computer bios - and programmer works fine.
Does it mean that memory 29F200BC is damaged?
It's no possible to solder back and check the ECU in the car beacouse I bought it just for testing.
Seller promised that ECU was operational - but who knows.

Is the any trick to read this eprom or it should be very easy?

fault codes list 3,f1,11,64 where can i find fault codes list from citroen

hello m8,
till yesterday i use original vcm with v75 with date 2011, but i unfortunatley turn it on with 2012 and cant program injectors etc.. Can i safely use ids v80 with crack from this forum?

hello friends. I have a problem with the installation of Xentry 3/12.
with me the error occurs during the installation -5011. have already installed the fix -5011, but it does not work. Which entry in the reg. I must change to eliminate the error.
Many thanks in advance for your help

Hello
I need hex for VCDS 11.11.4
If anyone can help me please email me [email protected]

Thank you in advance
Best regards

hi . please you help me for update digimaster dm18 and i need file setup . please you help all member

hello . i have problem with mercedez S221 problem with ABS system . i change new ABS control unit but need to do scn coding online pleas you help me.

hi mates

need your help
i have C4 sdconnect clone look like orignal ,on platform _w work perfect in das mode
but in xentry always losting connection and no ignition detect +12V
im using 01 2012
pls if have idea how fix
many thanks

Hello experts,

I need immo off for fiat punto 1.2 16v 2001 188A5000
ecu 0261204983 Bosch ME73H4

Thank you in forwards.

Attached Files

0261204983.rar

220

78.06 KB

Download

I am wondering if someone had the same issue. I went through DAS Xentry 11 2012 installation and completed it. I still cannot get it work but it is a different topic. The problem is that I lost Wireless Internet access from this laptop. On the other hand, I can access internet through the cable.

I lost Wireless access just after I completed the installation. Is any fix for this? I can see wireless access point icon on the Taskbar. It is indicated that the connection exist but I cannot access any internet page at this moment. I believe I've got some Wireless access blocking but not sure what is the cure. Any ideas are very helpful.

I did go through the installation guide and did 4 partitions as was described. I believe I followed the instructions preciously. I went through SD_11_2012 Disks 1 and 2. I initiated install from G:\stardiag\setup.exe. I had only one error during the installation process - "Error occurred while updating C:\USERDATA\config\HHTwin\HHTWIN.INI". I disregarded to it and continued the installation.

I am not sure if I have a successful setup. I don't see Xentry or DAS icons on my desktop. I only have the following icons available - STAR UTILITIES, SD EXPLORER, Star Browser and Info. I also have some icons on the taskbar. Do I have to do something else in order to get access to DAS and Xentry? What this would be?

Please let me know if it is normal and what I can do in order to get the Xentry work.

Thank you in advance!

I completed the installation of the DAS Xentry 11.2012. Now, I cannot access Startkey Center. I am getting Display Launch4j with error description -This application was configured to use a bundled Java Runtime Environment but the runtime is missing or corrupted. I am not sure how to surpass this error. I used Fix for Startkey center Xentry 05 2012 but it does nothing to let me enter StartKey Center. Any ideas on how to fix it in 11 2012 version. I am stacked and cannot do much from this point. Any advice is highly appreciated.

Forgot to mention, I did not get much errors except "Error occurred while updating C:\USERDATA\config\HHTwin\HHTWIN.INI". Now, I can locate this file.

Hello all

Because my Autocom stopped working as it should, and the repair is uneconomic, I decided to buy a new one.

The question is:
Does anyone have a good source, website, place in China where I can buy a 100% good quality Autocom?

Maybe some of you bought the Autocom and he looked inside on PCB's and can confirm visually that it is of good quality and everything works fine.

On the one hand it could be the new gray version but it does not bluetoth.
On the other hand, the old version does not guarantee the software update.
But the work with bluetoth is more comfortable.

I need your advice ..

Regards

Hello friends!

Just installed DAS/Xentry 11-2012 and 09-2012 on two different laptops with two different Muxes. Both laptops and SD Toolkit work really fine via LAN cable and the WIFI settings are all correct and configured.

The laptops also have a connection with the Road24h network but the SD connect Toolkit will not connect with the SDconnect I have a very good and stable connection but the Toolkit does not reconize the Mux. I hope someone have a solution. When i try a D-mux everything is ok so there is something wrong with the WIFI settings or so. The most strange thing with the 09-2012 is that it did worked for two weeks and now not anymore I also tried a USB WIFI stick but with the same result...

Hi guys,

my dad has now a lttle problem with his EIS i guess.

Sometimes when he puts in the Key and its cold outside, the light goes on, but he cant start the engine. I have allready read something about those problems on a website from a guy who repares such kind of problems, but its 1. too expensive and i guess i can repair it on my own.

So, are there any "problem zones" or something like this ? Somehting like cold soldering joints ?

Thanks for your help in advance.

IMMO TOOL TMW HELP

hello please i need honda PCM code,for civic, here is the vin number:

1HGFA16546L065989


PLease help me with the pcm code, thank you

Special Problem ^_^

How To Remove Developer kit mode on DAS and XENTRY from Version 01/2012

Please help me !

Best Regards

Hello
know somebody how settings LAN and wifi on wmware for C4mux..
Thank you for all idea

Hi!
someone is owned by Daimler web login or a solution for it?

https://login.i.daimler.com/internet/login

Thanks.

Hi folks,
After many requests, here you find the Bin folders for DAS Xentry 7-2012 + Thesaur of same version.
Bin Files include all the DAS Xentery fixes and ready for sdconnect.

Results =

Password: mhhauto.com

Best regards to all

Attached Files

DAS Xentry 7-2012 Fixes.txt

803

182 bytes

Download

Hi m8 .
one question for all!
possible immo off for mercedes benz ,modell e-klass , w210 , 300d from 1995-1996 ??
system descrition : RCL whit led /green in mirror, unit IFZ in right footwheal located , key whitout transponder !

MANY THANKS ALL SOLUTION EXPLAINED

Attached Files

Thumbnail(s)
   

Me again,

hi,

i want to connect an EIS with a ESL Emulator. I have now research in some Benz diagrammes and now i know that one pin no1 is K-line. but in which pins are (+) and (-) ? And on which side ? Because on left and right side there is pin 1to8 in ?

Thanks in advance. Jacek

Attached Files

Thumbnail(s)
   

Hello to all MHH members,

Here you find two Team Viewer Video's I created to help some members in Config there Sdconnects.
The Two Video's Cover the Following:
1: Update Sdconnect Firmware
2: Config Sdconnect as adhoc and Workshop ( Via Router which helps in SCN coding )
3: Some new tricks on Sdconnect.

Password: mhhauto.com

And since the new RS rules,

Public Traffic
(download of your files without Folder Share e.g. through sending and publishing the download link) 1 GB / day 30 GB / day.

This means after some time, and with high trafic downloads files will be missing.
To avoid this problem, Download Rapidshare manager and then add me to ur contact list ( [email protected] ).
After I get ur requests Ill share all Mercedes 11-2012 soft's ( DAS XENTRY, WIS-EPC, Sdmedia and PL_67) with you.
In this case no download limits will be...

Hope this will help

Attached Files

Sdconnect Links.txt

2038

150 bytes

Download

http://www.careucar.com/upload/service/r...-crack.rar

I am wondering if someone can share or point to a location to download

1. Compact2 reg files to add and delete
   
2. Fixed DAS\Bin Folder 07.2012