I have been hunting for solutions to recovering bricked ECM/BCMs for the past several weeks and haven’t found a clear answer. I have invested in a few new tools as I want to become more experienced in this area and would appreciate an experienced persons response in this area. I just purchased a HEXProg 2 and DC706 (to start). I have an AutelIM608 PRO and Launch Elite VII scan tools also. I am looking for training, guidance  whatever may seem fit for a newbie in this area. Where are people finding the calibrations to reflash?  I don’t mind purchasing more user friendly equipment. Please help me.

Hi, can any one send electrical drawing for nemo ABS/ESP system and Central lock trying to retrofit one have all
Components got stuck on schematics ?

Hi,

I have problems with my meriva S10 - she need about 6s to start, while first try is after 2 turns of flywheel and then computer (probably) is shutting-down injectors . Hi and low pressures (after and before pump) are ok.
I want to try change ecu firmware and I'm searching for flash never that 2010year. Stage 1 would be nice.
MED17 EDC17C19 TC1792

Hello everyone, Does someone has the wiring diagrams for the Peugeot 508 2014 ? Thanks in advance!

I have for sale ecm titanium full promo version. Subscription valid until December 27, 2024. price 1050 euro. I from Poland.

Good evening guys.

I am new to MB software installation as I do not work much on MB and my xentry installation got lost due to a bricked hard disk.

Can someone please advise what is required to diagnose a 2018 GLC.  I have a c4 which should be original.

I already made a fresh install of windows 10 pro 64bit.

I read through the posts but I'm still at a loss on what I should install.

Thanks.

Delete post

SH72543 ecu, i need dpf off please

Attached Files

Mazda_CX-5_2012_2.2_Skyactiv-D_150_hp_Denso_SH12_OBD_NR.rar

5

813.11 KB

Download

id.rar

2

352 bytes

Download

I need help with stage 1 for this file. Can anyone help?
thanks

Attached Files

03L906023KM_9979-20241128-181809 org egr_off chks_ok.rar

4

105.43 KB

Download

Hello.
I am trying to do retrofit in RDC. I have placed the three antennas F/R R/R R/L and I can't find where to place the F/L.
Does anyone know where to find the front left RDC antenna on a 2001 E46 cabrio? 
In the picture you can see the base (6) in which only the F/L antenna (2) fits
Thank you.

Attached Files

Thumbnail(s)
   

Just wanted to reach out and ask for some guidance from the community. 

I’m receiving these faults after replacing front left and right crash sensors with exact part numbers as the old sensors. Can’t clear the codes using the xentry software. I believe I need these codes cleared so that I can lock/unlock the srs control module and remove the srs error from the info display. This car was in a small fender bender and the airbags deployed I’ve cleared all faults for seatbelts and airbags just can’t figure out these crash sensors. 

I’d be willing to install resistors if that does the trick just not sure what ohm resistance is needed or if you even can do that with these sensors. Any help would be appreciated.

Attached Files

Thumbnail(s)
           

Hi there. I am looking for tuning of my file, the most you can get out of stock engine. It is a Ford Galaxy with VW ASZ engine.
Sorry if I forget something or else, I am a bloody beginner with chip tuning, and trying to learn by this way

Attached Files

038906019LD-SG 5801.rar

4

151.81 KB

Download

Hello guys.

Has anyone mastered old m3.8.3 golf mk4 gti?

I needed to put pops and bangs and hardcut.


thanks

Attached Files

golf4.rar

10

75.95 KB

Download

Hello
I bought a Porsche Cayenne that has an error in the xenon lights. The two ballasts are different, one of the two is Chinese and I plan to replace it.
I have Piwi3 with a Rlink X7.
The first Ballast is a Hella 955.631.194.00 and the second is Chinese.
Will it work if I buy a Hella 955.631.194.02 to replace the Chinese one, in this case the two will be different?
If I find a used one is it possible to recode it for my vehicle?
Does anyone have the Piwi procedure for coding?
Thank you very much

Hi all,

Would you provide me the PIN code of this ECU please (DCM3.4) Renault CAPTUR

Thanks in advance.

Attached Files

CAPTUR DCM 3.4.zip

9

1.28 MB

Download

Hi

I cant seem to find a CGW on W117 to disable the tele aid as it keeps showing SOS Inoperative does anyone know how this would be disabled on this model i have had a look in the IC172 also and cannot find anything related

Mercedes-Benz CLA 200 d Shooting Brake 2018 W117

can someone remove this noread from the file?

Does anyone have any knowledge on what needs changed in the hex code for the t87a, t93, and the e41?  I’d like to unlock my modules  so that I can tune them directly with Hp tuners.  Currently I have to read them with my dc706 then convert the .bin file to .hpt alter it with the hp software, save it, then convert it back to .bun and flash it in with the dc706 again.   I was hoping someone  could tell me what to change in the .bin file with hex editor so that I can write them with hp tuners directly.   Any knowledge on this is greatly appreciated!

Hi, can enyone help me with info on how to read this Continental BCM, clone, transfer the chip, 

what software to read the code pin and do proxy alignment, 

or which chip, eeprom stores the data.

Attached pics.


Best Regards.

Attached Files

Pics.rar

8

280.97 KB

Download

Hello, can anyone answer the question of whether it is possible to change the language of the dashboard using the vvdi programmer?
Its possible to read mcu dashboard and change language?
Thanks.

Hello 
can one help me swap imoo data from GEN2 to GEN1 
Thanks to support me

Attached Files

TopGear Audi Q5 NEW.rar

3

389.7 KB

Download

TopGear Audi Q5 ORG .rar

3

437.3 KB

Download

Hi guys
I am looking for the correct software for power steering control module for vin number WAUZZZ8K8FA011562 Audi A4 2.0 Dai


Sent from my iPhone using Tapatalk

Hi guys

I bought Tiguan 2016 and there is DSG DQ500 but it shifting on low rpm, in town I drive on D7 1200rpm I know that is possibility of SW modification of shifting.
Question is how safe read/write this gearbox?
I'm not professional automotive person so I don't have any expensive tools. I own just as hobby Kess/ktag, sm2pro, all china clone. It is possible to read with this tools or what clone up to 800-900€ is possible to buy for DSG? KT200, FormulaFlash...

And next step if I read it is here someone who can modifi file? (Of course not for free)

Thanks a lot.

is anyone able to remove the rpm limiter on the camaro? who is able to make something like this please pn with price

Hello, I bought keyfob on Aliexpress for Mitsubishi Space Star 2015 and successfuly programmed immo, key is working, but I can't program remote. Procedure found in launch is not working becouse of different blinking on remote than procedure (press lock and unlock for 3 blinks, then press unlock once) but key led is contantly lighted up when button is pressed. How it can be peogrammed?

Hi, can someone is able to remove speed limiter if i send flash from EDC17C18?

Thanks

https://m.youtube.com/watch?v=0UBYMtzl8K...p=2AEOkAIB

https://www.tiktok.com/t/ZTYAhLWfX/


Full unlock for HP tuners.  How to read the hex file, what line to edit,  what to edit it to, and how to re write to make it unlocked for hp tuners.

You can also send them in to us and we will unlock them for $100
JCLLC 712.204.3955

I’ve seen a lot of question on unlocking the gpec2a ecm’s on here. 2015 and up.   Figured I’d make a post with the diy links.  

https://m.youtube.com/watch?v=0UBYMtzl8K...p=2AEOkAIB

https://www.tiktok.com/t/ZTYAhLWfX/


Full unlock for HP tuners.  How to read the hex file, what line to edit,  what to edit it to, and how to re write to make it unlocked for hp tuners.

You can also send them in to us and we will unlock them for $100
JCLLC 712.204.3955

Hi 

can someone help me with immo off , need to put updated software on this ecu , its a calibration file , all works but immo is active 

Many thanks

Attached Files

WinOLS (PIWIS-PT3G_10001.ols (Original) - 394198).zip

4

723.95 KB

Download

Dear all Member

I support Coding, Programming when replacing a new Unit, used Unit for Toyota Lexus cars (SRS, EMPS, Engine, Dashboard...)

If you want to do it quickly and reliably, please contact me. I will help you faster.

PRICE for All model Toyota/ Lexus.:
- Coding: 50$
- Programming: 100$

CAR INFORMATION:

Brand: NX350                 Year: 2022
Model code: TAZA25-AWZLT




Information on EPC:



BEFORE: Many light turn on after new Dashboard replaced.



AFTER: All OK, many light turn OFF (PCS, LKA, LDWS light Yellow -> White,..)



All services are in the attached txt file.

Please contact me via whatsapp (informations find contact in my profile)

For urgent cases that you need to do immediately (ECU Security, Programming, 12 digit keycode...), if you send a message and there is no response, please call me. I will support within 5 minutes.

Attached Files

Toyota, Lexus Keycode, EPC, GTS, ISTA, Repair Manual, File BIN Service.txt

1

8.04 KB

Download