does somebody know if there is any breakthrough for Bench reading/writing post 06/2020 Bosch MD1/MG1 locked ECUs? Is there a tool that can read them now or someone who can share new informations on this topic? So far I've only seen the inhouse unlocks by aulitzky, femto... and Flex seems to do VAG MD1/MG1 ECUs, but I guess we still have to wait to get our hands on.
Hello,
I bought 1.9tdi for work travel. It was already tuned, but I need help for tune fix.
Car has:
big ic
GT1856V hybrid turbo (" 250hp 2,3bar")
4bar map
Problems:
Incomplete 4bar map calibration. It says that air pressure is 0,6 bar on idle and should be 1bar. And that is why car goes to limp mode. "Too low charge pressure".
Car smokes very heavily. It does not need to smoke that much.
Car has also "diesel pop and bang" while rise acceleration pedal. That is not needed, because it is only white smoke and farting.
It also pops while upshifting. I can live with that.
Checksum correction needed.
I am happy if you can tune 1.9tdi and could help me. Tell me your price.
Hello. Please help. Patch has already been made, the FSС codes have been downloaded, the Russian language is in the menu MGU and in the KOMBI. Navigation is working now, but cities and streets in Latin letters instead of Russian - that's the inconvenience. Can this be fixed so that the patch doesn't get erased? Thnx.
hello
I have a rcd 500 mp3 radio for which I wanted the code, I managed to read the flash with m16c flasher with max232 serial interface, I made a mistake and deleted MCU M30833, now I have the code but I can't write more details: RCD500 MP3 3C0 035 XXX B model: CQ:EV1572G VWZ5Z7G XXXX XXXX can someone help me with information where I'm wrong, are there any extra settings for m16c flasher, is it possible to write only with rx tx?Can someone give the id from the dump? Maybe this is the mistake, when reading the log it doesn't have an id
Hello everyone, please can someone point me to the right direction on how to fix the this GLA BATTERY TERMINAL PROBLEM, when I put another direct wire from battery to the kick-starter the car start normaly from inside, but the fuse or module on the terminal don't pass this direct current to the kick, I tried to change the the terminal fuse i was told it's good that the crash that happened trigered it please what do I do in this case, thank you in advance 🙏🙏
I have a problem with a 2008 year w221. A friend accidentally cleared the "zgw" and I managed to bring them back to life with the help of "das offline" and "sdflash" everything works as it should only there was a problem that the car's mileage was 196000km before and now it has almost 250000km. Where did the difference of 50k kilometers come from? The car was recently bought, is it possible that the seller rolled back the mileage? and is there any way to use "das" or "vediamo" to go back to the mileage of 196000km that it was. Thanks in advance for your help.
I am breaking my head over a Seat Arosa 1.0 with a ALD engine. It simply doesn't start and the Engine ECU and immobilizer doesn't trigger any error.
Both ECU's are happy and the keys match. I replaced, checked all sensors (Crankshaft sensor, camshaft sensor), and they are all good. But, it doesn't ignite..
Hi, could someone explain to me how to enable devtool in techtool 2.8.241 step by step?
I have everything unlocked, but I don't understand whether it is programmed in programming (I still have some functions in gray) or whether it is programmed in the devtool program, but when I change it, nothing happens (e.g. I tried to set all service inverter, e.g. oil hydraulic 5000, etc.)
Hello, I need to turn off the immo in the MS45 controller in BMW, the
controller is installed in the e87 housing with the M54B25 engine, the
starter turns, there is no spark. I have tried various combinations,
still no reaction. Regards
Hello friends
I have a trouble with Citroen Jumper 2.2 hdi SID 208 ecu
The original ECU it’s broken and can not be read!
I have buy other ecu with the same hardware Number but with different software!
I have programmed the new ECU and the car now starts but gives many dtc …
Its possible if I find the ori flash from the correct software to load it direct to this ecu or need any special procedure?
Thanks in advance
Best regards to all
Been doing some reading when i flash my new file to the car some how the ecu is remembering the codes dont no how. I got a warning message from kess saying warning to add pins to the ecu so the ecu doesnt store codes!
I think there is one option on kess for boot mode but i maybe wrong . i would rather not de-solder the chip if possible. If this doesnt work with kess what other options are there .
