Hi gentlemen
I have one bmw e60 lci with lm2, had original bi-xenon headlights I must to exchanged with headlights aftermarket…. All work only high beams working 1 min and turn off,must to restarting the car and again same….. working 1min and turn off …. And in LM get error - A8C7 Bi Xenon,Shield faulty …..
How and what do I have to code to make it work well????
Thanks in advance !!!
I've read Polo 6 TDI 2017 Model ecu, it's Delphi DCM6.2V and I'm struggling to decode the files I've read, I need immodata from Flash and EEPROM.
Can anyone decode the attached Flash and Eeprom files, please? I'd appreciate any help you can provide.
After replacing the R230 EZS MPC 908 type 2J74Y with the MPC 9S12 type 1L85D, the meter display is ------- and nothing is displayed. The engine starts.
The EWM and ECU are synchronized with the EZS. Also, the meter is edited to FF.
I would like to set the current distance to 123111km. Thank you in advance.
Hi!
May be someone know where is immo located in Mercedes Econic (truck) aprox. 2008 year.
On ignition switch there are a little plate with 3 wires outside, looks like just a reader (photos in attach).
I was looking behind dash and other places.. cant find.
Looks like immo is in Engine control module ?
Hi, i have problem with Audi A3 8P 2003 2.0 TDI BKD. The power steering red light, dsc, and abs is on. In last week i changed, g85 sensor and steering angle sensor module botom steering wheel. The problem is not unresolved, vcds -> 03 ABS -> Coding 11 -> 40168 -> g85 adaptation and "not possible". My question is, if there is an error in the can gateway "single-wire operating mode", can it cause an adaptation error?
Can someone please check attached ori and stage 1 file.
I have a Passat 1.8tsi with med17.5 ecu which won't start after stage 1 file is uploaded. When I flash it with ori it starts ok. Is modified file done correctly?
I'm using Ktag clone to read and write.
Have difficulties set odometer reading right on this bmw.
First i read cas4 and eeprom from dash.
Dash showed 277855km and needed to change it as 291000km
I changed eeprom(160D0WG) reading to desired 291000km and then changed also cas4 (5M48H9) to same number.
installed all back to car and odo reading shows 266995??
Took everything back to table, set cas to 0 and dash again to 291000.
Put everything back and again 266995 on dash. No tamper dot, no fault codes.
What i`m missing here?
All reading editing and writing both cas and dash is done with hextag.
Ori reads from dash and cas in attachment.
Hi folks!
Have some problem with my audi.
My temp gague is showing about 70 degrees ehen car is shutdown.
When I drive sometimes it can show me 130 degrees, 80 degrees and 0 degrees.
Have change waterpump, thermostat and g62 tempsensor (green) and bleed the system from air.
I have controlled the temp through diagnostic and it's around 90 degrees when gague shows me 130 or 0.
Got good amount of heat in the car!
Gonna do a cluster test through ICON tomorrow at work.
What you guys think? Cluster fail or wiring fail?
Have someone had similar problems?
Best regards! /Swedish audi owner
Help to decide witch one to buy?? Prog or multiprog? Does multiprog has same funtions as vvdiprog? I dont care about ecu reading have Flex. Does anyone have both of them, need your opinion. Thank you in advance.
Hello, i have a problem with Nissan Qashqai 2014 1.6dci 96kw. I need to fix it tomorrow and would like to know if someone had a similar issue and guide me in the right direction. All these DTCs are for Thermo plunger relay and Engine fan is running when it should not. The car was already in another shop and they could not fix it. These are DTCs in ECU:
I did instrument cluster in Renault Trafic - IPC4.2 CK system. Everything works as it should but. I need Can-filter. Connection diagram also. What do you recommend and where to buy? Rather URGENT.
I did instrument cluster in Renault Trafic - IPC4.2 CK system. Everything works as it should but. I need Can-filter. Connection diagram also. What do you recommend and where to buy? Rather URGENT.
Hello. I need help with removing the speed limiter. It's set at 90 km/h.
Ford Transit from 2007.
6C11-12B684-AC
6C11-12K532-DP
8C11-12A650-CE
YW8PG6AP8CPK
.CGS-ST10F276-5.03.1
Hi
I have a Land Rover Evaque from 2016, and due to a weak battery, the radio and the display on the center console stopped working. The fuses are good, there is no communication with the radio unit, please give me some advice or a diagram.
Hello everybody someone Can please share esys plus or esys launcher please ? I got one but when i launch esys launcher its says date modification and close. Need to do coding please.
