Hello ,
Im stuck with an error I cant fix .
I have version 01/2011 installed using JC tools.im tring to read a w204,
I get a fault in xentry Diag at step 3 ,VIN checking/confirming,
errors
1.17-7.870
2.27-7.870

communication error I think ...is 01/2011 set up for C4 by default
I use a clone C3..
do I need to change to a Bin for C3 ?
will a later Bin fix work ...?
Thanks for your time
Darren.

Hi


I have tuned my file . and would like to know if it is any good.
Thx
http://1drv.ms/RFzNXO

Hello!!
I have this ecu. Bosch 0 281 020 067..from Man TGA truck..
Anybody know, where is the eeprom to read it..to make it immo off?
Thanks!!

[attachment=44231]

[attachment=44232]

Hello, does anyone have service manual or any documentation for the gearbox in title? Thank you !


Any pictures are wellcomed

Looking for Damp full flash of the Volvo V70. The panel is dead. Diagnostics show that the wrong configuration
dash YZK 69294-630T 3K91D VCC 8637996 2004year
Thank

Attached Files

v70 flash omega.rar

99

33.16 KB

Download

does anyone have a tuned file or at the very least a definition file? i have been trying to work this out and figured i would atleast try and ask....
thanks in advance

No more avalaible for sale.

Guys I have not had the time to read all the threads on Bosch ESI so i'm not sure if someone has already posted this somewhere on the forum but here is Bosch ESi 2014 on torrent.

Thank me if I helped you.

Attached Files

Bosch ESI 2014_1 torrent.txt

3961

73 bytes

Download

Hi can some one help me with setting up balance shaft timing on nissan d40 engine 2008 cant seem to work it out

hello mates how are you


im trying to read MC68HC08AZ32A with no luck i connect 40000 osicllator to pin no ( 58,59 ) and attach MC68HC08AZ32A mcu to QFP64 adaptor , chosse function and set 40000 trying to read showing me this msg in attached picture

i tried to read it with UPA programmer in-circuit also failed

note that im not good in soldering and desoldering

with orange programmer i can read in-circuit as orange pins , i tried to do as this with xprog but dont know where is PDX in xprog m connector

Attached Files

Thumbnail(s)
           

is it possible to remove the speed limiter on an 08 plate vauxhall vivaro whilst having the file tuned ?
also will a galetto clone be able to write the ecu on this year.?

please pin bsi c2 95160 2002r 1.4hdi

Attached Files

c2 bsi 95160 org.rar

41

1.22 KB

Download

HI ALL FRIEND.I LOST THE MIMORY CARD FOR LUNCH DIAGUN .
I NEED YOUR HELP TO SOLVE MY PROBLEM.
THANK YOU

Are that some one that have org file ´Porsche 996

0261204790
1037357109
0041570275003629

Comand NTG1 after firmware update want not start, have somebody solution for this problem ?

firmware update was from ----> HERE

thanks

please correct checksum

0281012549 1037A50292 1.9CDTI EDC16C9 120HP

my.rar

81

211.69 KB

Download

The problem is this, run hard.
The problem is this, run hard.
Once I did diagnostics showed me the following errors:
crankshaft error potentiometer throttle, EGR valve, wrong Kan. As I read the actual values ​​of these errors it follows, for example the gas pedal to the pressure to change the value from 2% to 99.6%. EGR valve also.
Also as stored errors disappear after 1 min, and then again appear.

Hi I wonder if anyone can make a good stage 2 file for the above vehicle, s3 k04, s3 injectors, autotech internals and neuspeed intake.

I have had several stage 2 files but all cause hesitation or misfiring. When logged with vcds getting 130 bar of fuel pressure actual. No misfire showing either.

Hope someone can help.

Regards

Attached Files

1P0907115D leon ORI.rar

42

664.52 KB

Download

I am looking for the drivers for the Original BASIC2 System the blue one of Mercedes. I tried the ELOTOUCH drivers for the Compact3 but the Touchscreen can not be used. Is here anyone who have the right solution for the drivers. In hardware manager it shows Comport 3+4 not present and the Realtek Audio drivers also not correct. The Touchscreen also can not be used. Please help.

Thank you..

Hi guys,

I have a 2010 vw polo 1.6 tdi (caya engine) in at the moment with the following fault in the engine ecu:

6551 - system voltage
P0562 00 (037) - too low
not confirmed - tested since memory clear

I have checked ecu measuring blocks and battery is showing 0V.
I have tested battery with multimeter and all is good, all other units have no faults and voltage is good.

So it seams that ecu is not getting a good reading from where ever it picks its battery reading from.
I have looked on ELSAWIN but can't find any info on where the ecu would pick the battery level from.

Can anyone help me with this?

Where does the ecu get the battery level reading from? Which wire on the ecu?

Thanks in advance guys.

hi can someone help me with my star diagnose , i have no icons any more on my desktop , it was installed with big icons like original .

i can open xentry and das if i go to "all programs" .

anyone can solve this problem

thanks

hello

I am looking for a compatible damos with EDC15P+ ibiza 6L

make your offers

thanks

Im looking for big archive of damos with good! quality.

Not public damos like its in all forum (about 2gb or 3)

Contact me pleace over pm with price.

Hello everyone, not sure if this is posted in the right place with me so sorry if so, my father purchased a mk5 gt TDI golf last Friday from eBay stating it had done 29k millage, I hadn't seen the car or know he was buying it until I saw it Friday night parked outside, I done a car check because I thought it looked dodgy and the price he paid and it came back with this info:

Source
Dvla date 21/05/13 201k millage
Dvla date 06/03/10 15k millage

Are their any software that can check the real millage? Can VW check if its been tapered with?

Many Thanks

I need security access code for parking brake passat B6,PLEASE
Thank you very much

Hello Mhhauto

Year / Date : 04-05/2014
Version : 2014
Developer : DAIMLER AG
you need 09.2013 as a base, you can find it in torrent section


Regards

Hello Mhhauto

Year / Date : 04-05/2014
Version : 2014
Developer : DAIMLER AG


Regards

Hello to all members. I made a lot of uptades/programming on lot of cars. I just updated an e93..All modules are done. only the FRM3 modue get this error: "Global Vehicle Communication CoAPI. 1060 Fehler in Codierungsbeschreibungsdatei" .The communication with the module it´s ok there are a few error like mirrors doors and so on on it, but i think this must have nothing to do with the programming. Know someone what is it?? I use ista-p 52.2.001 Expertmode and icom interface.. Thank you in advance..


P.S. I haven´t find a thread like this please when already existing please remove.Thanks

Hello I have a bmw e39 2001, the navigation screen is asking for a firmware cd anyone knows how to fix this problem I have a bmw 1.4 scanner please help.

Hi we have a vauxhall Zaria B 2008 z19dt with fault codes p0001-75 and p0001-5b vehicle starts ok revs ok and fuel pressure desired achieved, but when driving going to accelerate vehicles cuts out has to see an ignition cycle to restart starts ok untill next acceleration fuel regulator valve has been changed in high pressure pump and new fuel filter fitted wiring to fuel reg tested ok from PCM. In tank fuel pump working ok.
Any help regards Tony