Hello,

Can anyone help me with a immo off file for a range rover v8 bosch ecu 0 261 204 901 from my 1999
rover part no:NNN100660
And in what chip is this file?


regards Charger



http://i957.photobucket.com/albums/ae53/nsautoservice/2014-05-0215-54-34337_zpsa836e09c.jpg[/IMG][/URL]

http://infoodessa.com/index.php/entry/et...hunta.html

hallo how have multidiag I want know this Mercedece included in system (mb w212 cdi)

Hi I got passat B7. I got w warning light on which says the bulb is blown. Front beam Light is on all the time even if i switch off the lights completly. The bulb is fine i tried different bulb but nothing. Do you know where should i start.

I need original dump for rear SAM modul on W211 with mcu 1l87j

211 545 35 01
5DK 008 047-31
Q: 05
HW: 4303
SW: 4703

Thank you

I need a ori file from a Landy 2,7 V6

ECU: NNN500750
SW : 857378650

greez from germany

Hi,
I have Delphi DS150e new VCI Non Bluetooth up and working with latest Software (Thanks to you guys).

I also Have latest Wurth Wow; again thanks to you guys.

NOW bearing in mind that up until a few weeks ago I didn't even know what a VCI was!

What are the advantages/disadvantages of Using DS150E with WOW over the Delphi software? As I am a little confused, as usual.

I understand that it is just a case of copying Delphi firmware to WOW (re-naming original ) and updating. Then you can use both?

Many thanks for everything. Thinking I should Donate something as you Get what You Give.

Carl

Hello,

vaspc 19.01.01 + hotfix DUTCH

Please press thanx its helps you

have fun

Attached Files

Document.rtf

286

520 bytes

Download

Hi,
i have the following Problem.
on my GlobalTis the Pictures, Wirering Diagrams are not displayed.

What can i do?
New Install with a older GT and then Update to GT32B?

Thx for Helpfull answers

Hi. I need to know how to program new remote key to Rover 75 2.0CDT, 2001 ?

I would appreciate some input from a seasoned Diagun user - how to do a quick I/M readiness test with the diagun on a vehicle? Without going through each system...

Memory Card Explorer To Read and Write PCMCIA Memory Linear Sram Cards, NO ANNOYING PASSWORD, NO THANKS BEGGING, just download and enjoy. Only for Windows 95,98,2000 and XP.

Attached Files

Memory Card Explorer 3.16.txt

1551

73 bytes

Download

hi everyone has anyone got obd pin out for diagnostic socket I need to convert to use xentry c4 sdconnect

thanks in advance

hello,did anybody had situation that ELM327 won't read any fault codes,using any available application? I have ELM327, like this on pict,
and I am using it for hobby,not for some serious job, I connect to almost any vehicle, I got readings, but it won't show any fault codes... I connected my car(2007 Mitsubishi Outlander II), on ELM327 there are no fault codes, but I know that there is fault code related for disel glow plugs...

Hi All,

I got a KTS520 (genuine) from a friend who no longer needed it + a T30 laptop with PIWIS V29 installed.

I flashed the KTS from V29 and every thing went OK. I then tried to up date the PIWIS to V30. Unfortunately this failed and the T30 turned into a paperweight with only two options 1: restart installation 2: recovery, neither works.

I then tried to use a VM with V34 installed and tried this with the KTS, but now it is no longer recognised, using DDC the usb port shows as USB#302 regardless of what I try, delete the existing entry / delete the ini etc.

I have rebuilt the T30 with a clean XP and installed ESI and the FWupdate, yet I still cant connect to the KTS.

The power supply led flashes as it should. I have even opened it up to look for bad joints, cant see any.

If I plug in just the USB cable and connect it to the T30 the small led next to the USB port lights up brightly, then when I plug in the power supply the power led flashes, but the led next to the USB port suddenly goes very dim.

I am stuck as what to do, if I can just get to communicate with the KTS that would be a start.

One request, does anyone have a ghost image of the T30 V29 PIWIS software, so at least I can get the T30 back to a good situation.

Thanking everyone in advance.

Bigfoot

Bmw e90 2007 I have CCC professional to CIC Professional conversion Retrofit.

Who knows how to activate navigation with ncs exper

Hello friends
in my 136 version, why probe is detected with the number 926 573, normal is RLT 2002 PROBE, how can I fix this error? already tried reinstalling but no effect
thank you

gentlemen, as the topic is looking for pinout teeth to Connect with this on the table.

Hello all MHH friends
I need pin from DUMP or virgine for Peugeot 207 MED17 0261201864
Thank you for help me

Attached Files

peugot 207 eeprom.rar

87

3.73 KB

Download

For ICOM: What is usb dongle and where can i buy it?

Does anyone have software that provides vehicle unibody and/or frame measurements? Looking for something that provides frame dimensions when I have something on our frame rack.

Any help is appreciated!

Password abbad

Attached Files

WoW Keygen 2012.rar

763

10.61 KB

Download

Hi there ,can anyone help me sort out password and username problem with jlr v131 tried user JLRQ5013 and pass L405X152 but no luck, just keeps telling me its failed , not connected to the internet with it and put it on my other computer clean xp pro sp2 . Ids v86 works perfectly on a separate computer but jlr just simply beats me any help ideas guys thank you all

hutchy36

Has anyone done Pt Cruiser 2003 with obd lead for Digiprog 3? or is it chip off?...Cheers
Regards Kev

Just tried it with obd didn,t work

I ordered Chinese New Kess v2 clone from internet site and my money gone.
Until now didn't get the item I order...

Please somebody know trusted source to order New Kess v2 clone?

I am using DAS on a c3 with the 11.2012 version and I am trying t o disable scr and dpf using data developer in variant coding. However, when saving the changes I get the 8.561.6067 error. I read that the error isn't a DAS error and that it is actually a control unit rejecting the changes. Is there anything I can do to get the changes saved? Would the das bin fixes do anything? Any help is appreciated

thank you

Edit: I was able to "change" the settings on an unconfigured control unit, but the settings didn't stick. When I rescanned the settings the values were back to their old setting.

Edit: I'd gladly pay with PayPal for any help that leads to a solution.

hello to all i need to clear crash data of Nissan Juke module

988201KV0A
Bosch F01G07208E
eeprom 95640
thankss in advance

Attached Files

juke 988201KV0A 95640 crash.rar

169

2.41 KB

Download

Hello Mhh-auto member . I need Username and password in vag odis

Look the picture

Attached Files

Thumbnail(s)
   

hi guys need anther pin for polo ecu pin code 95320

Regards
Clyde