I just bought a Kia Canival with a Becker 7820 headunit and, I need new maps for this one, I only have 2005 maps, but there must be some better then that

My map software CD i V4.0 and its Europe map

Anyone ?

Hello,

i would like to make diagnose on table for this Airbag ECU after delete crash data.
Car: OPEL
ECU's maker: TEMIC
ECU: 13129843
Crash data stored in: 95040

is it possible to figure out which pins are need to use ??

Which one is 12V, 12V ACC, Ground, CAN - H, CAN - L, L-Line?

Hi folks
Chine OBD V4.88 DIGIPROG

Im alitle new to digiprog and eeproms and the manuals for the 4.88 that followed from china are not up to date!
I have the CAS3 in the footwell and I thought this needed to be conected with the BMW CAS adapter but I did the milage with the OBD2 (PLUG16) so thats good..

BUT I have the following problem..

First I opened the odometer, and took a copy of the 080odwq chip (8pin) and saved sucsessfully. Then I unsoldered, and did what the manual says,
I went in to BMW-E90-DASH and when the option came "old milage 150.000km" "Write new milage" I entered 110000km and then it displayed after prosessing 190000km.. I thought I chould cinfirm, so I soldered it back, took the obd2 on the car and did the prosedure for BMW DIAG in the car menu.. When it said old 150k I confirmed, and it said "attatch cluster" so I did.. The milage went to 190.000 and I found out that the CHIP was only alowed turning UP, so I buyed a replacement chip.. NOW HERE IS MY PROBLEM...

I connected the chip to the ST1 clip and I found the saved file in EEPROM menu on the digiprog. I write this file to the chip but then the chip got locked to 150.000km again.. So im back to start 1

Can anyone tell me what I should do when I get another replacement chip.. What do I do with the DUMP file in digiprogs eeprom. It look like the milage must be in the beginning out from the numbercodes I see.. Can I delete someting or change some numbers there??


Thanks in advance

Hello, colleagues
I have a problem with the start of my Mercedes v203.
2 days ago as I was driving and the traffic lights all lit my feet on the dashboard. Then I stopped and then I can not light it.
Give a contact and try to light it but the starter does not turn.
After which I did with Star Diagnosis diagnostics.
And the mistake that has been in the motor computer:
P0600 CAN fault The databus is faulty.
P0600 CAN fault The transmitter is faulty.

Please, help....

Hi,

I have a problem with an A3 1.6 diesel 66KW.
Software was read and try to write before unlock.
Software can be read with Galletto3 and write with the same software and the conclusion was that the ECU is unlocked. Bad conclusion, I guess.
When try to write the new file (chiptunning), Galletto3 work to 100% but at finish give an error(to transmit file to team).
After that error the car cannot start and Galletto3 wont let me connect to ECU DATA.
What is the solution to make the ECU alive?

Regards,
DMS

Please DO NOT Ask for PASSWORD on the thread / post / forum (ONLY BY 'PM' = 'PRIVATE MESSAGE')



PLEASE NO SPAM


BEST REGARDS

megane2 68hc9s12dt256 cihip flash eprom, one to one another uch copied it worked then I copied another car to flash failed what to do????? only the eeprom can be deleted, copied or????

Attached Files

Thumbnail(s)
   

Hello again everyone. Once again I am trying to make my life harder...

I am looking to see if there is a way to have DAS open HHTWIN in fullscreen?
I do not like looking at this small window and always have to click the fullscreen button.

I know when using shortcut's you can set options in the target line to have it open in fullscreen. I am not sure how HHTwin is called up through DAS and dont want to cause it to not work..

Has anyone tried to do this before?
O yes, I am running version 11/2011

BMW KEY PROGRAMMING SERVICE
EWS OR CAS2,CAS3
FREQUENZY 315MHZ
PM[/b][/align]

Hello Everyone,

Can someone help me to solve the problem of Chervolet captiva 2011, C140.
It can be started and run, but after running 20-30 kms, sometime the acceleration pedal is not affected when i press the pedal, It means that when i press the acceleration the Torque and odometer are not raised. But when i press the pedal to the end of the range (mean as Maximum acceleration), Torque and odometer inscrease, then it come back to normal work.

We have replace many things as: fuel pump, fuel filter, vacuum, Temp. sensor, camsaft and cranksaft Poss. sensors, cleaned the Exshauted Canisters, ignition coils.

Thank you very much!

Hello Everyone,

Can someone help me to solve the problem of Chervolet captiva 2011, C140.
It can be started and run, but after running 20-30 kms, sometime the acceleration pedal is not affected when i press the pedal, It means that when i press the acceleration the Torque and odometer are not raised. But when i press the pedal to the end of the range (mean as Maximum acceleration), Torque and odometer inscrease, then it come back to normal work.

We have replace many things as: fuel pump, fuel filter, vacuum, Temp. sensor, camsaft and cranksaft Poss. sensors, cleaned the Exshauted Canisters, ignition coils.

Thank you very much!

hello i need EGR off for renault megane scenic
ecu delphi 1.5 DCI
thanks in advance

Attached Files

8200334419 flash original EGR on.rar

38

16.45 KB

Download

I need some advice I have a USB-link Comm adapter and all the truck Diagnostic software but now want to get some auto to do my own diagnostics. I originally got a ELM327 adapter and installed ScanXL but I am told that is only good for Code pulling. I have a windows 8.1 Tablet PC 64bit and I am looking at either AutoCom/ Delphi with a DS150 adapter or Auto Enginuity with there ST06 adapter. I would like something that can do all Engine, Trans, Body Controllers, and ABS/ AirBag. Please any help would be much appreciated. Thanks in advance.

Hi friends i need egr delete from this mapping edc16C34 206 1.4 HDI

Attached Files

206 1,4 HDI 0281012525 1037376757.rar

119

434.38 KB

Download

i want to read new bsi with MCU 9S12XEG128 mask 2M53J for recalibrate mileage .<br />
do you know programmer for it?<br/>

Sent from my GT-I9505 using Tapatalk

hi to all
pleaz can i have the pin code for opel corsa d year 2010 from dash
dash controle johnson
eprom 35080 st
best regards

Dear friends , please help me with a smart fourfor. I have replaced front sam , did the initial startup with scn , but It asks for "code number for control unit assignment" Can you please help me.
Vin WME4540322B108905 my das version is 03-2012.

Hello,please, I look for a virgin dump for uch Laguna II phase 1
MC912DG128ACPV
have you it?

Hello,please i need pin code for my nissan navara

Attached Files

Thumbnail(s)
   

death link 

hi
I have Opel Movano 2002 1.9DCi
Why the cooling fan works right when you turn the ignition, low temperature, and does not stop, someone has a link or electric scheme
thank

Can someone help me to extract the ISN from the ECU
BMW
0 261 204 420
AM29F200BB
Thanks a lot

Attached Files

flash ecu 29F200BB 0 261 204 420.rar

178

82.22 KB

Download

has anyone used digiprog 3 v4.88 to change mileage on 2002 ford focus ?

seems it will only work on newer models with eeprom.
what other tools will work .

Can somebody please uploud the latest software for opcom with firmware.

It would be a big help for all of us.

Kind regards

i needed the workshop manual
for jeep cherokee
2.5 vm engine diesel
1995 year

thanks in advance

Hi

I just installed Odis with VAS on my PC (xp, 32bit, java the correct version) and i cant get to open VAS. Odis works perfect.
When i try to select VAS from "DIAGSTARTER.BAT" it sends an error of three files :
- ADM.exe
- GFS.exe
- GFSFlash.exe
and at the end a popup with "VASEGD" saying it has a problem loading a resource file "resource_de-DE.dll".

Any solution?

hello friend

please i need file original (ONLY FLASH)AND READING MICRO CHOICE of this car:

ford s-max 1.8 tdci 125cv year 2006

and the ref ecu unit is:

siemens vdo sid206-5ws40419f-t 6g91-12a650-lf 6DXF


I NEED IT ASAP.

THANKS

hi

i dl this: http://mhhauto.com/Thread-Microcat-Hyund...at+Hyundai

i installed it on Windows 7 32bit and windows xp

but it's not working.

i get message Dongle not found

i ran the .bat files. also copyied the files manually

and deleted the file: System32/mg16.dll

but still helpless.


do i need to buy a dongle? from where?

any help?

Hi. I have Rover 75 2.0CDT 2001 (115hp). I've installed chipbox at MAF sensor.

It has reduced consumption, but power wasn't increased.

1. What is best to do for consumption/power ?

2. If I write file to my car from 2.0CDTi (131hp) will it work and increase power ?

Or if someone have tuned file it would be great.