Hi everyone,
i need help with dashboard from Sprinter 2008 313CDI 2008,
I read from dash 25LC640 and read full mcu from ezs (temic) flash and eeprom section,
but i can't calculate odometer to set 150000, now 468585.
Please help, calc, anything...
thanks in advnance...
for those who wondered what the small black box with the led, switch and alligator clips is used for i just did some research:
the big red alligator clip supplies +12v to the Kess main unit on pin 12 of the 25pins male D-connector; +12v is wired trough a 1N4001 diode to the switch which powers the led trough a 2K2 resistor and supplies the blue/white/orange/yellow and red wire with +12v (switched output).
the big black alligator clip supplies GND to the Kess main unit on pin 24 of the male D-connector; it also connects to the LED (negative) and to the gray wire and the small black alligator clip (GND)
the K-line is connected to pin 10 of the male D-connector and to the green wire.
So Basically it uses only 3 pins of the Kess main unit (+12v, GND and K-line) and it outputs 5x switched +12v (blue,white,orange,yellow and red) , 2x GND (gray and small black crocodile clip) and 1x K-line (green).
I hope this info is useful for those who never used this adapter till now.....
Hi there i have a genuine gm tech 2 and today power up and get just blue screen i have tried my spare vci and still the same i believe there is a so called blue screen chip to replace can anyone tell me where the chip is located as i have spare tech 2 thanks in advance
I have a problem with my opel frontera B help me Opel Frontera 2.2DTI X22DTH 2000 does not start - B0007 - immobilizer control module control module / motor (ECM) communication -. No ECM signal
Here are the default in ECU P1690 - Malfunction Indication Lamp (MIL) Circuit Open
hi
i need virgin eprom dump of A 646 153 20 79 0 281 011 162
edc16c2 cdi3---eep:95320
MERCEDES A6461532079 Bosch 0281011162
i this after reflashing the eprom whit vergin dump i should recode whit star mercedes ???
hello , i need immo off for iveco daily whit Bosch ms6.3 and eprom 24c16.
i used aetool , but car not start, i disconect immo box, and car no start, i need program inyector code?
the file no is fine for work?
please, i need help.
I need some info about the programming capabilities of winkfp. If I have to change an ECU for example an EDC16 what is from another car, do I need to mod the ISN in the new (used) ECU or just make an update with new VIN. Sorry for dumb questions now I'm just learning NCS and winkfp.
hi i need a full procedure to virginize the airbag unit in w203 by using the developer mode if someone have i have to do it in Mercedes C - 0 285 001 373 - Bosch 001 820 97 26 THANKS
MERCEDES BENZ STAR KEY CALCULATOR (SKC): Generate Keys by EZS / EIS Dump (ALTERNATIVE FOR SKC-MEHACO)
UPDATE: ALL EZS chips are supported now: HC05, HC08, HC12, 9S12, NEC (auto detection)!
Using this service you can calculate (generate) up to 8 keys by yourself from EIS/EZS dump only (without removing any part).
If you are interested in CR injector test bench, and thinking about to build your own, just take a look at mine uploaded on youtube.
Maybe you can take it as an idea.
02432 - Supply Voltage for Left Parking Brake Motor
I will like to know where the EPB MODULE IS ON THIS car, i will also like a wiring diagram preferable alldata will do, thank you, remember the caliber is working alright,
when i place dmm to test for the voltage on the left when park button is press, no signal on the dmm unit
hi,autocom 2013 r3 loaded to xp,after re boot program fails to load ,displays error .... themida file corrupt or manipulated or has virus,any solutions please:
Hello.
Does anybody knows what pins these Fgtech v54 mini gender and volvo truck adapters change?
Or someone have main unit pinout?
Need to know where are j1708