Please Help,
I need full dump for BMW E65 engine control unit 0281011415 1037377759 Master and Slave Flash MCU and EEPROM
or you can repair eeprom in slave controller
change according to the speedometer km
error 4A63 EWS manipulation.
let sync any more
Danke im Voraus
Hello Community, i have a little problem!
Is in EDC15 any V-MAX?
The Car runs in 5th Gear 210kmh and 5000rpm and in 6th gear the Car stops at 230KMh and only 4000rpm.
The Car is Seat Leon Top Sport 1.9TDI 150HP.
Hi Mate
Now, I am in trouble with the installation of XENTRY DAS software.
My C4 SD tool is from China and Xentry DAS program is 09 /2013 version.
I tried to put a key (which is generated from KeyGen Programthat was uploaded on here MHHAUTO) at STARTKEY and Xentry Diagnose key
seems to work well...But DAS key does not work.
In this case, what should I do?
1. Is there any Firmware for all different clone C4 SD tool?
2. Firmware can be affected by XENTRY DAS software version?
3. STARTKEY is different following KeyGen version?
If so, what kind of keyGen I should use?
Please see attached the image files and give me any helpful advice.
I am looking to by a autel Maxidiag MD802, diagnostic tester. But can somebody tell me about it can test the engine and transmission on a jeep grand cherokee crd with mercedes engine and transmission...???
The last ucandas i bought can not do it, it can test all other controller in can but not the engine and transmission...
Hopre somebody can help me, maybe with pictures of the car list in the tester.
hello
I turn to worm suppression fap Audi a4 1l9 tdi ecu edc16
fgtec reading V54 ok
I did dfp with ecusafe but it does not work
it joined the read file with fgthec
thank you in advance for your dear friends using
SMART VIN Decoder is only application one the market which can provide you with full data from VIN (Vehicle Identification Number) from factory like
- Production date
- Engine Type
- Transmission Type
- Model listing
- Interior color
- Paint
- Full equipment list
and many more.
Just enter your VIN number and you will get full information about your SMART car.
Don't forget thanks and reputation button
hi my friends i have a problem with RENAULT CLIO II 1.2 2004 with ecu SIEMENS EMS3132
S110140201A
8200326395
flash AM29F200BB the car has no a/c i need the immo off of this ecu i think that is with can because i can't found the pin 58 as the ecu without can any idea thanks
Hi! Could you help me with this car? my problem with fault code 2510-001. Pressure in air intake system almost 2600 mbar, mechanism on turbine is ok. All ok, but when fault occurs car in limp home mode. please help me
Hi guys! It seems that I have a problem with the wis program.
It seems that program has a missing file and can't start. The file missing from the directory is "788cda5b-41df92ca"
The hole directory path is C:\\Documents and Settings\\SUPER NET 7 \\Application Data\\Sun\\Java\\Deployment\\cache\\6.0\\27\\788cda5b-41df92ca
Is there anything to fix it?
My system runs in vmware xp sp3.
hi,
Guys please tell me how to replace the dash on the sprinter 906 2007, but without SKN and adaptation.
What needs to change in erpom that would EZS the panel adopted as their own?
Heard that you need to change the ID, but where and what kind of ID do not know
Tried to change the VIN but did not help.
Hello all, I finally got this internet thing sorted out and recently installed Mitchell On Demand (Repair & Estimator), since the computer that I have been using for the longest time, has finally died.
But back to the topic at hand, whenever I check mark a part, it doesn't add up in the total at the bottom. Is there any way to set it up to estimate the total? Because I have to write down the numbers, save the quote, reload it, and punch in the prices and quantities for it to finally calculate the grand total.
I have a built rally car with BMW 4.0 / M60 engine, it runs so good, but now there is problem...
There is 2 error codes:
6 / Injectors- General
42 / Speed Signal
sometimes goes to safe mode, not running until 6500rpm
when just 6 / Injectors- General error is in it going till 6500 rpm.
when is in safe mode the base rpm is 1800
Inpa not working correctly with it /missing the car, else parts/, checked with delphi to..
The flowing thins checked, changed:
Injectors, lambda, cables, spark plugs, sparks, crank shaft sensor, camshaft sensor
Speed signal not was until now, but not was any problem with it! Into that model goes the speed signal from differential. That missing can causes that error? Or any help to what can causes that error!?
What is Injectors- General error?
![[Image: 1995-caterpillar-3406e-2.jpg]](http://usafarmequipments.com/wp-content/uploads/1995-caterpillar-3406e-2.jpg)
