please i nedd immo off
iveco 35c15 3.0 hpi edc16c39
EPPROM AND FLASH THINKS

Attached Files

iveco 35c15 0281012193.rar

137

500.11 KB

Download

Hi guys ,
I desperate need CAT ET 2010 or 2011 .
Please , working link for download and please all included
activation codes , factory passwords , please.
I have ET2011A and working good but I need factory passwords
for advanced options . Any help will be respected.
Thanks

DVD with FSC Enabling Codes for BMW used for programming and encoding up to 03/2007. Personally I tested on BMW E60 and works like a charm, just get the files from DVD as <vin last 7 digits>-00020001.* and burn them on CD.

Attached Files

fsc.txt

63

197 bytes

Download

Hello to all. I need HELP

I have read from 0 261 204 798 the eeprom ST25P08 but this is only 22kb.

is this size right ????

thanks in advance

sito

Hi
please help me.
Very urgent need PIN for: VF1BM0F0528579897 RENAULT MEGANE 2

Thanks

Hello, i have problem with Peugeot 206 200year, 1.4 Motronic 7.3.

Only one fault code stored: 2212 Coolant temperature sensor.

But car sometimes cold sometimes hot.....have problem. Cranking but engine not start?

Any suggestions?

hello all , can someone help please .
I need diagram of chain comand motor 200xdi Kyron 2006.
best regards

hi guys

on some car my xentry 07/2012 gives me "internal error 3.1 - 3.8"

you have any idea?


thanks

Hello.

I need to update MMI BASIC to language Polish. Defaultly there is no pl laguage to choose (car imported from NL). But models from polish distribution have PL language.
I have vas 5054. Can I flash MMI BASIC with new language using vas? I need some special flash cd? Please help.

hello,

pleas I was able to program trans for this car 219356 2007 but I need the -y- type coding so I can put it dev mode , so ican code it , or if you have the string that starts with -79- for the came car .

thank you

Hi,

today i received a message that update 2.13.1.1 will will available.
My previous install was 2.13.1 without xml-fileactivation.
The program works like a charm since i did the online update to 2.13.1.1

The update is going correct. But after if i select a vehicle and press the OBD-Button right below, i got a blank screen. If i click on the blank screen the "OK"-Button to connect to the car, a window with internal error pops up. Only generic OBD is working.

Any suggests or solutions?

Thanks.

Attached Files

Thumbnail(s)
   

Hi,

today i received a message that update 2.13.1.1 will will available.
My install was 2.13.1 without xml-fileactivation.

The program works like a charm since i did the online update to 2.13.1.1

The update is going correct. But if i select a vehicle and press the OBD-Button right below, i got a blank screen. If i click on the blank screen the "OK"-Button to connect to the car, a window with internal error pops up. Only generic OBD is working.

Any suggests or solutions?

Thanks.

Anyone nows what kind of delphi ecu a Ford Transit 2.4L Diesel 101KW has?

Please help.
Need a clean Dump for airbag Honda Accord 2010 77960-TL0-G920 M1
I can not find anywhere else.
Thanks!

Hi guys I am trying to prepare the 95320of A6 2012, I am using DP3 butnot sucess, there is a trusted machine that makes it??

Many thanks

Hello, I have a VW Touareg 5L V10 EDC16, 2005. It does not start. There are two engine calculators, how to IMMO OFF? How to UNLOCK the steering column? How to repair the steering column? thank you

may I ask you smth Please
I have a renault Clio 2 YEAR 2002
and this car has a problEM when I open the ignition to start the car the red led diode is on and does not turn off for me to allow to start the car and the SERVICE light begins to flash
both keys are OK
the door can be locked and unlocked succesfully
Plesae where must be problem

I also changed the UCH and again the same problem
I also check the fuses near battery
where do you think must be the problem
I chaned the UCH and program agaN the same keys with NEW UCH and Again the same problem


I also checked the fuses near battery
So the problem is
I turn Ignition ON and the red diode does not turn off for the car to start it is always oN
and the service light blinks always

Regards and thank you

hi,
i replaced RCD300 with RCD510 in to my y2007 MK5 Golf,
now radio is not shuting down completly and overnight the batt
is draing and in the morning battery goes weak and cannot start.
i heard that CAN Gateway has to be recoded or updated.
is someone here who solved this isue?
thanks.

Immo 0281010043 w210 2.7 CDI where is it.

please. Will you do me the cat off?

Attached Files

2.4. v6_ori.rar

23

264.36 KB

Download

Hi,

Can someone get me the original dump???

Best Regards
RS

Attached Files

5wk43749_crash.zip

100

2.31 KB

Download

Hi

Please for help with clear this dump file from Fiat


Thank you

Attached Files

95320_crash.zip

93

1.2 KB

Download

I have to turn off the seat belts buzzer in this car but regulation icon in consultIII is inactive.

Hi, i need dump dash for eprom 93c86 for VDO dash, W203 C30 CDi AMG year 2003.i pay for paypal
Thanks.

Hello to all,

what is the difference between the "normal" PSA-Interface hardware (hardware-clone from china) and the "adapter XS Evolution Lexia3" ?

Is it true, that flashing the interface-hardware makes the difference ?

How to go back to the "nomal" state (from XS Evolution -> normal)

thanks in advance for help !

-Lupus

Can everybody help me citroen c5 2.0 hdi immo off please?

This ecu edc 15c2

I read ecu here is file .


Thanks

Attached Files

citroen c5 immo.rar

117

156.95 KB

Download

hi all member please you help me for service manual ssangyong KYRON 2006 disiel . thank

Hi all, I wonder if any body here could help me. I am looking for repair manual of Toyota Tundra 2007 -2010.
Thanks in advance.

I need help !!! I think I really screwed things up this time.

MB 3/2013 0n Dell D630

Das in no longer communicating with the Multiplexer after installing “all” the Addons through “Online Update BG”

Fault (1.2)-.503.13011

It acts as if it's not there. It does show up at the bottom taskbar. I checked SDnet Control and it's there, I did a self test and it seems OK..

So what could have happened ??? Which updates screwed what up ? Is there a way to reverse it ??

Any help is appreciated !