i update my collegeau's laptop xentry-2011.09 software to 2013.03 version, and all right, but i don't see the NEOPLAN in the new software.And this is type need to my collegeau. What is the problem and solution?
Regards,.
jezzus
sorry for new thread, i remember the neoplan is al type in software, but not. So, no problem in new software.
hy i would like to acces cars like 212 prototyp and so on i get always an error is there a patch or swomething else out that i can acces to this vehicles in das ? i use 3 2013
Mercedes Navigation-CD NTG2 Audio 50 APS Europa Version 15 2013-2014
Part No A1698278959 | Database for this CDs : TomTom Q2/2012 | 4.78 GB
Seven CDs brimming with navigation data for 29 European countries, with roads and paths, Towns, villages and many POIs. Western Europe is covered with the version 2013/2014. More than 7.5 million kilometers of navigable roads familiar with the navigation across Europe in version 2013/2014. In Eastern Europe, along with Poland, the Slovak Republic, Slovenia, the Czech Republic, Hungary and Greece from Croatia this version now also fully covered.
In Bosnia and Herzegovina, Bulgaria, Macedonia, Romania and Serbia-Montenegro, the main road network is added. Over 1.8 million of the most important and updated targets in more than 40 categories are included on the product, for example, gas stations, parking lots, museums, restaurants and hospitals.
Coverage:
CD 1 - B/GB/IRL/L/NL
CD 2 - A/CH/D/FL
CD 3 - F/MC
CD 4 - I/RSM/V
CD 5 - AND/E/GBZ/P
CD 6 - CZ/GR/H/HR/PL/SK/SLO
CD 7 - DK/FIN/N/S
HI ALL I NEED SUGGESTION after a short in wiring diagram the ecu has been useless and i have to change it but i do not found the right number of the ecu my original number was 89666-6080 DENSO AND THE NUMBER THAT I FOUND IS 89661-13070 DO YOU THINK THAT THE NEW ONE IT WILL MARCH WITH THE CAR BY THE WAY MY CAR IS TOYOTA LAND CRUISE 2005 GXL OR I HAVE TO PUT THE IMMO OFF TO IN THE NEW ECU BEFOR MOUNTING IT IN THE CAR AND WHERE CAN I FIND THIS FILE THANKS
Please THANKS + REPUTATE than ask for password in PM! I will upload more soon.
Edit By Modpariscy Answer your PMs, you have made only 2 post and you make the Members Spamming/Flooding the Forum with password requests.
If you can't handle so many PMs just post the password.
Thread Closed. Too many reports that poster don't answer PMs about password.
I used to remove this Blinking using DAS Dev. mode as follows:
SRS ECU ==> Dev Mode ==> Actuations ==> Complex index of auctions ==> Steuergerat verriegeln (FN_SG_Verriegeln) ==> F3
I changed W204 Front SAM.
Everything went fine.
Now I have Problem with Radio.
It turns on then after a while turns off. On radio screen I got a message to remove protection!!!
I am interested in learning how to read/dump ECU and possible write back tuned version later for my car (my car only). I have VAG Engine, 2.0 TDI 170 bhp CFGB engine code.
It seems that required software is VERY expensive...
What software and hardware (cable) is recommend for my engine and can it be done through OBD?
Hello to all,
I installed xentry 01.2012 I work with sdconnect without any problem but when I open Xentry Simulation or DAS Simulation I face error Fault (1.17)-7.870 of course if I edit cal.ini to D2 problem will be resolve but I can't do it because I use sdconnect pls help me about this problem.
My customer has a E85 with m suspension. He wants to raise the vehicle with 2 centimeter.
Will the original springs fit and will it raise the vehicle 2 cm?
What more options are there?
I've got a W209 CLK Coupe from 2003 where the available languages are german, englisch, french, espanol and japanse.
I want to change the language to dutch (cluster) but it isn't available. I also looked in Xentry (11-2012) but no dutch.
How do I get the desired language?
I have a key to make but some one did damge the IMMO and I can,t
find a used Immo to change the MCU ,
the ECU has aflsah AM 29f400 and if some one has an immo off flash
ECU SIEMENS 5WY5866B
I've installed Nissan consultIII 9.21.01 on a stationary pc and it works (program starts if I click consultIII shortcut), then I install it on the HP omnibook XE3 laptop and it doesn't work. If I click ConsultIII shortcut, program menu not appear, but if I open task manager there are launcher.exe and NDA_launcher.exe tasks. Whats is wrong? On this laptop I have Clip and diagbox installed too.
OK, I solved problem
It was missing driverLinx Port I/0 driver in system32 on my laptop
greeting members
next issue
bmw 320d 100kv
vehicle during acceleration make prekid.vozilo has until zagreje.posle this power is not felt. grešaka.fumpa no car repaired VP44 fuel. parameters followed by the office shows the air mass meter interchangeable. past 3 days the car started to eject a large amount of white blue dima.vozilo no oil consumption or vode.molim for a leash
Car: BMW F18
Working content: the replacement of EPS
Software: E-SYS3.22.5 database 49.3
The WFL_00000E20_000_000_003 file is not. Therefore cannot cable related design coding file.Use Auto logic to solve the problem, step is the programming of EPS, Coding. And then use E-SYS to read the relevant documents, found that change.
The file SWFL_00000E20_000_000_003 is missing, to SWFL_00000E20_001_005_001. this time, I used my own database can also export related design coding file.
Excuse me, is there SWFL_00000E20_000_000_003 the database, how to solve the next encounter such problems, does E-SYS have the function to modify the SWFL file? If there is, how to modify.
![[Image: 58d19911189eaebfe608e7056a3d46f2.jpg]](http://i47.fastpic.ru/big/2013/0602/f2/58d19911189eaebfe608e7056a3d46f2.jpg)
![[Image: 7a441365a12c263c0c5e635e4e207a1e.jpg]](http://i46.fastpic.ru/big/2013/0602/1e/7a441365a12c263c0c5e635e4e207a1e.jpg)
![[Image: 52534422.png]](http://img845.imageshack.us/img845/9438/52534422.png)
![[Image: 62225557.png]](http://img829.imageshack.us/img829/8436/62225557.png)
with any immo file or how to do this?
