Hello Members,
I am trying to Install VAS-PC V19.0 English_GB.
I try to install Brand CD for VW then I got a error "FDICopy failed: code11 (User Aborted)". AUDI,Bently are OK.
I tryed V18 and it was same. Also I tryed to V19.0 EN_USA and same result.
Hi to all guys!
I have a problem with this ML class with EDC15C6 and the battery was dead...i renew it but now shows Start Error in dashboar...what is the solution???I am ready to read the eeprom in the ecu but i cant read it what type it is and from which manifacture....and Where is the PIN1...Is there any software which can do this???please help guys
Good for all,please some body can help,to give me pin code for my radio CHRYSLER;who have this spécification:
PART NUMBER: P56038585AL
DATE CODE: 2641
S/N: TCCAA2641Z4395
SUPPLIER: 17719D
Thank's
Hello again. I have next problem. Chrysler Voyager 3,3 1996 year.
I have no ignition on 4 from 6 cylinders . I dismount engine computer and i have broken two from three transistors Motorolla 4221. whatsi is it . Can i replace this transistors fro other ??
Hi,
solve anybody problem with this yazaki dash ? Dash have not changed km. Dash donot show right temp and donot show speed. Km counter work fine. Board is cleared and resoldered, but not work. On board is not much io, if have internal error this mcu ?
hi, i need virgin dump DME BMW ME9 320I series,
ecu bosch 0261 208 582 or 0261 201 159 or similar,
my car is bmw 320i petrol 2007 year .
thanks to all.
Hi guys.
Gallardo winter parking in a garage does not start.
On the instrument panel when the ignition does not appear check engine.
There appears AIRBAG light and will not start the radio.
I checked the installation.
I checked the ECU power supply and fuses.
Please send any diagram ECU thx.
I have been trying to piece together a routine for getting Autocom 2012.3 running for awhile now, I have read so many threads and other sites that I have basically just confused myself at this point. I don't remember where I got all the tools I am trying to utilize, some from mhhauto for sure but I think some stuff/info I gleaned elsewhere as well. I am hoping somebody in the know can review my process and find the error/errors that I am making.
Here is my failed Autocom 2012.3 install routine
1) Web turned off on target computer
2) Use a Keygen with a web located serial number (20418) to generate a Hardware code, Keygen I found will actually edit an existing "Fileactivation.xml" if you point it to one, I do this later.
3) ) Install Autocom 2012.3 CDP Cars
4) I then run the appropriate certificate.exe file I found on this site "CDP_CAR_CERTIFICATE" (At this point I always get a "no certificate to remove" message), I then extract the contents of the CDP_CARS_CERTIFICATE.exe and manually copy the "n1.acx" and "n2.acx" files in the extracted data folder to the data folder located in my Autocom installation folder (C-Program Files-Autocom-Data). I then copy the certificate that I extracted from the CDP_CARS_CERTIFICATE.exe file to the root Autocom installation folder (C-Program Files-Autocom). This may be redundant or my problem but I end up with the downloaded and extracted Certificate file and n1.acx and n2.acx files in the correct locations I think.
5) At this point I think I am supposed to copy an 819 byte "Patch File" to the Autocom Installation folder, I am unclear what this file is and how I get it so I skip this step (another possible point of failure if this procedure is otherwise correct)
6) I Run Autocom for the 1st time and the registration procedure begins with no web connection active on the laptop.
7) I choose "USB method" and Autocom creates a "FileActivation.xml" file on the usb stick and prompts me to remove it and put it in a computer with a live web connection.
8) I move the USB stick to another machine and run the Keygen again on that machine, after inputting the same serial number and hardware code that I used for the install I point the Keygen to the "FileActivation.xml" file on the USB stick and the Keygen appears to successfully edit the "FileActivation.xml" file on the USB stick.
9) I then return the USB stick to the laptop I am trying to install Autocom 2012.3 on but I recieve an "unknown error" prompt after it tries to use the edited Fileactivation.xml file on the USB stick, the activation fails and starts the whole process over the next time I try to run Autocom.
10) I have tried to manually copy the edited Fileactivation.xml file from the USB to the Autocom root folder but this changes nothing.
I have uninstalled Autocom and started over but this brings the same result, I would greatly appreciate any help in identifying what I am doing wrong here.
Thanks!
could please tell me what should I read memory in a SMD 7584113 marac S04 BOSCH 0261 163 2008 MINI COOPER information to know if the car has not detected or scanner DME or to put it in the simulator and I say check the computer memory if you have information compu okay, and check the lines of communication and are fine no problem with harness or fuse and if they could send me a reading virgin and memory tell me that I must read.
I have installed Renault Clip v117 and it get a message when I try to launch with crack file. Launches into activtion page ok with original RSRwin file though. Please can sombody send me activation code?
