Hi

Would need the pin out of this unit, which is one of the modern Laguna 2008 2.0 DCI 150hp with ecu EDC16C36, with Original MAGPro2 short I was reading at 36% because the car cuts the ignition for non-load in battery but the battery is good, and I while I'm loading with tweezers in another car. So here wanted to try to read on bench with pin-out. Does anyone have it or can get it?

Also I have a galleto 2 clone and wanted to know someone has got to do with this interface because I fear for coding injectors leads.

By the way I do it with the engine cold, as in some renault if the engine is hot or not let you read.

Hello members,

I'm new to this group so please work with me on how things work here. I recently had to perform a backup recovery on my laptop and now this program is giving me this error "No valid DAS licence; DAS will now be closed." any help on this will be greatly appreciated, thanks in advance...

When I go into the DAS menus to reset the transmission adaptions on my W204 I am presented with the options as shown below:

Control Units > Drive > Transmission > Transmission Adaptations

Then I see

- Assignments of hydraulic shift elements
- Display and reset of adaptation data (SHIFT)
- Performing adaptation (SHIFT)
- Resetting of adaptation data (Torque Converter lockup clutch)
- Adaptation of torque converter clutch

I assume the proper menu I need to choose would be "Display and reset of adaptation data (SHIFT)?

If so, then I see the following sub-menus

- Upshifts
- Downshifts
- Reverse gear
- Saving of adapation data

If I choose Upshifts, then I see

Adaptation values of shift 1 - 2:
Adaptation values of shift 2 - 3:
Adaptation values of shift 3 - 4:
Adaptation values of shift 4 - 5:
Adaptation values of shift 5 - 6:
Adaptation values of shift 6 - 7:
Resetting of adaptation data

If I choose Downshifts, then I see

Adaptation values of shift 7 - 6:
Adaptation values of shift 6 - 5:
Adaptation values of shift 5 - 4:
Adaptation values of shift 4 - 3:
Adaptation values of shift 3 - 2:
Adaptation values of shift 2 - 1:
Resetting of adaptation data

If I choose Reverse gear, I see

"Do you wish to reset adaptation data?"

So essentially, the adaptation reset is broken down into upshifts, downshifts and reverse gear. What do I do here? is this the proper area and which one(s) do I need to reset?

Thanks alot

hi friends!
anyone knows any database which can be consulted for explanation of fault codes? some high-end cars are difficult to diagnose codes. would be nice to have a database in which to consult and obtain an explanation to know where to start.
if there is please someone tell me.

hi everyone,
i installed the latest version of autocom (2013.1) and get it to work with the delphiautocom patch from debütant.
it is all fine but the firmwareupdate fails. it says: cable not connected, bad voltage etc. (but everyting is ok)
so i read about to install 2012.3 again, copy the firmware folder from the 2013.1 into install directory and update under 2012.2
because i have to do this often (on various adapters) that is no solution for me.
or is there a other patch/crack solution.
there where no such problems with firmware updates in 2012.3
perhaps anybody can help?

Hallo friends. I must removed immo from ml 99y. 3.2 . (bosch 0261204783) . Enyone have solution. thx

Hello guys please me help with crash
9677909280 continental

Attached Files

95640 vcrash.rar

76

1.87 KB

Download

Hi,
please i need help Ford radio code S\N. V026878
Thanks

Hello,

I'm looking into buying a Autocom CDP+ clone. My seller is offering me two different options. One is "blue box" and one "white box", both with 2012.3 software - the price difference is minimal. I'm planing to update it with the new software. Do I need to do any modifications to the hardware (I have some experiance with soldering and programming)?
What should I look for in a good Autocom CDP+ clone? What is your experiance with those clones? Anyone knows any reliable sellers?

Thanks in advance.

can anyone help with network settings in vmware to get the yellow gt1 digihead to work....

Anyone seen this message after doing a manual service interval reset?

The message is not continuous - it's only there if you try to go all the way down the service interval manual reset route using the steering wheel.

please post suggestion.
the
Car is Mercedes Benz S Class SL-350 2011

hello
please someone can gener keys.
ezs 210 545 00 08
MCU1 0D69J
MCU2 1h52a
variant 051
thanks


[attachment=21657]

dear friends help me please 2011 citroen c4 airbag crash give me clear dump

Attached Files

c4air9677909280crash.rar

35

2.36 KB

Download

Hi!

I have a BMW X3 2.0D 150hp and This car have two DPF or catalyst, The first in engine output have sensors and second in the middle of the exhaust line haven't sensors. empty the two catalysts? or just the first or the second?

Thanks

Hello everyone!!

I saw on the HW Key Generator for 2013.1 Autocom/Delphi these extra modules:
- MaxModule
- DieselMax
- TurboCharger
- RTDLogger
- GWM
- GWM_MAX

What are each of those for?
Can we activate them?

And another question,
I saw a friend's Delphi original sofware that in the live data it shows the factory value and actual value of the parameters.

On my versions of Autocom/Delphi i didn't find anywhere to show me the factory value of any parameter.. Is that another extra module or what?

Thanks anyway for your time!

Heya all,
I have a 2008 Toyota HiAce Eng 1KD D4D giving EGR issues.
Is it possible to do an EGR off?? Which tool can read the ECU file??

Cheers

Heya all
I have a 1998 Astra G X18XE1 with a dodge Eng ECU. Have read the old ECU file with Kess V2 + then written file into replacement ECU. It tells me "Immo function not programmed". Is it possible to do a IMMO Off + then rewrite or possible to extract PIN from file??

Cheers

OOOOPPPPSSSSS!!!!! Sorry for double post

Heya all
I have a 1998 Astra G X18XE1 with a dodge Eng ECU. Have read the old ECU file with Kess V2 + then written file into replacement ECU. It tells me "Immo function not programmed". Is it possible to do a IMMO Off + then rewrite or possible to extract PIN from file??

Cheers


OOOOPPPPSSSS!!!! Sorry for double post

Hey Mates

Im Seeking help with this issue,rough idle and once in awhile it would die out, is their a way to manually to perform a idle relearn.
our any tips what to look for g/s Air Flow

2000 nissan sentra 1.8l

Hello,
I'm looking for OFF PEUGEOT 406 2.0L HDI EDC15C2 0281010627.
I post the file 29F400 and 5P08.
Thank you in advance

Hello,
I'm looking for OFF PEUGEOT 307 2.0L HDI EDC15C2 0281010779.
I post the file 29F400 and 5P08.
Thank you in advance

HI guys i need to know your experience with this tool carman scan lite carman car diagnostic scan tool is it good because i need a tool who can scan all japonaise and koroen car and if you know some auther one witch can do the same work tell me please thanks :

: 1087:Hello.
I want to ask for help on a 1000cc Yaris ISZ-FE.Ref. :89661-52072. Fujitsu ten
I'd give a little power and can not find information on the location of IC. in the ecu plate.
What IC. should I use to record the new file.?
Thanks in advance and sorry for my ignorance, is the first time I try to do this job

Attached Files

Thumbnail(s)
   

hello friends .. you can check this file where is the error?
I can not get turn off the fap!

model:

51900698
0281015684
1037515036
AD3042 .
12 01 2011
EDC16C39

Hi I need corection milage is 12855km i need 1855km
Thanks

Attached Files

Thumbnail(s)
   

atmel24c02_12855km.rar

52

213 bytes

Download

Greetings!

I'm chasing a workshop/repair manual for my 2002 Audi A4 B6 2.4L 30v V6.

Either the whole manual, or even just an extract detailing the cam timing!

In English preferably, or German (I have a friend who can translate it for me )

Thank you in advance

Kindest Regards,

Josh

Hello i am looking for radio code vwz1z286264933

it is a vw mcd radio with navigation.

thanks

please
help me with code radio vw RCD510
VWZ1Z3K6399350

VW MID EU UP1 BVX
3C8 035 195
815 7 647 239 360

Attached Files

RCD 510 CODE.rar

121

2.61 KB

Download

hello
please pin out SID801 SIEMENS PEUGEOT 307
REFERENCIA 5WS40020G-T

Free version MMC flasher 2 for cars Saab and Opel .
The program works with adapter J2534 (open port 2.0)
The program is designed to read and write the ECU for Can- bus.
ECU trioniс 7 and trionik 8 have not tested it, so I do not have ECU for the tests, please test the software and write me - that you would like me to add to the software.
If you want to add new ECU in the software, send the ECU to me - I will add it to the software - you will get software for your ECU free
download software

Attached Files

MMC Flasher 2.txt

534

90 bytes

Download