Hi I'm trying to get into the programing key and airbags and odometer for my local bodyshop I'm looking to buy Digimaster III with 1280 tokens for this purpose will this unit do this purpose for bmw, Mercedes, cadilac I'm in Florida and if any one can tell me what are the tokens for and what do they mean. Also were can I read or if anyone can guide me as where can I learn the procedures to do all this. I'm an electronic eng reparing electronic equipment componet level for 20 years but now I also want to get into the car electrical repairs. Pleaseee helppp
Does anyone know what the DTC Code P0243 mean for the Jaguar X-Type 2005. I have tried looking ti up but it comes back with Supercharger/Turbocharger Westgate Solenoid Malfunction, but as this model has neither a supercharger or a turbor charger I think this may be a little wrong?
Hello I have big problem with my car. ENGINE IS 1.2, ECU Marelli 59.
-Engine not start but cranking.
-Fuel pump works
-CODE iluminating and goes off
-check iluminating and goes off
-water temperature lamp iluminating and gauge doesn't work
-fuel level lamp blink and gauge doesn't work
-low voltage on ignition coils
-no signal from CKP but sensor is in good condition and have good resistance but ECM doesn't see it.
-diagnose with ECM is alright
-diagnose with gauges, BCM-----there is connection and suddenly connection cuts off.
-I have code U1600 stored and after erasing it is ttored again so like immobilizer fault but CODE lamp goes off.....
I have no idea what is going on. I checked i think every earth point, and even changed BCM and ECU from donor and nothing changed sadsmile2 please HELP!
One problem SOLVED!
After disconecting Instrument panel ENGINE STARTED, diagnostic communication works!
but engine works only for 2 cylinders
Ignition coil is ok, wire ok, no spark at 1, 4 cylinders.....any ideas? Ah, ENGINE IS 1.2, ECU Marelli 59.
I'm having a problem saveing the key for Xentry 03.2013 in Star Utilities and StartKeyCenter.
I'm using NewGuide2i and the files that come with it to prepair the computer.
When I use C:\WINDOWS\zak\Starutils\StarUtils.exe and the commonlic.dll that comes with NewGuide2i I get an other Hardware ID than F:\Programme\StartKeyCenter\StartKeyCenter.exe that gets installed with Xentry 03.2013. I changed the commonlic.dll to version 1.1.701.0, Built on 2011/11/28 20:24 to get the same Hardware ID.
I have also delete lic_key_2.dat
The network was disabled during installation. The date was set to 16. april.
I have tried both Xentry Developer 1.1.0.exe and XentryKeymakerLt1MB.exe to generate keys.
hi @ all,
yesterday my autocom 2012.3 downloaded an update per isu.
after restarting the programm the update will be installed, but quite at the end i get an error message: "UpadteMainIfNotCorrect" stops working and the update fails.
anyone knows whats the problem?
see picture for details.
i ordered the new FGTech Galletto Master, does anyone know how to use it ?
Is there a step by step instruction out there ?
I already watched some youtube videos but what i mean is how to make the chiptuning so the truck or cars will not get damaged ?
Where to get the files to load into the trucks ?
I want to use it mostly on EU Trucks such as Volvo, MAN and Mercedes
Or i have to buy the VOLVO and MAN Scanners to do that tuning on them ?
Since we have more and more cars in our shop that require immo repair and airbag reset, I have received a new task : to learn (and apply) how to solve these problems.
Unfortunately (since I work nowadays 12-13 hours/day) I have very limited time to spend on research. So, here I am, asikng for your help.
I did some quick research on this forum regarding immo repair and airbag reset and I learned about the tools (software and hardware) that I need, and I drew the following conclusions : I need to use Ecuvonix Airbag Universal Repair 2.0 (for airbag reset), Immo Universal Decoding 3.2 (for immo repair) and UPA USB Programmer (hardware).
I downloaded sw and looked for hw, and I found these :
Wich one do you recommend ? I thought that UPA USB PROGRAMMER 27 Adapters UUSP V1.2 UPA USB seems more complex.
OR even batter what other tools, hw and software can you recommand (but keep in mind that I have received very limited budget since I'm a beginner in this area)?
What tips & tricks can you give me ?
My uderstanding as how this works (at least immo repair) :
I have to processes the dump file from the eprom and remove the immobilizer.
I can use a programmer to read the contents of the immobilizer eproms, and then Immo Killer or Immo Universal Decoding does some changes to the memory dump, which is then written back to eprom using the programmer, and the car is immobilizer free.
Is there any other way to read and write to eprom other that desoldering -> adapter -> resoldering ? If yes what tool does that and how secure is the process ?!
For Airbag reset can you recomment some handheld device (does the job via OBD, without PC connection and without desoldering)? Are these secure ? Or is it batter to use the programmer way to do the job ?!
I need help to learn from those who didn't forget their early days in this area, when you started to learn and needed help also. I don't need sarcastic replys and "use search button" since I allready did that and learnet things written above, and keep in mind that I've got VERY little time to do reserch and experiments.
Thank you in advance for your time (reading this and perhaps answering my questions and providing the help I need).
Best regards.
P.S. in the shop I work the most cars that come in for repairs are : VW, Renault, Opel, Dacia, Seat, Ford, Audi, Skoda, Mitsubishi (L200 in particular), all up until 2009/2010.
Dear's i need to reinstall Windows XP on my KTS 670. Because i have a connection error if i want to update the firmware.
And i can use the touch screen pen.
Do any of you know the default password for User: Star 2013 on a Dell D630 and or Administrator Password.
I’ve been trying to add a few add-ons downloaded from “http://stardiagnosis.aftersales.daimler.com/query/query/dvd/lang/en/branch/CARS/dvd/DVD201303” which is what I have. I unzipped them one at a time to a USB drive.
So I clicked on “All Programs” > Update > USB Update> picked the update on the USB drive that showed up in the window. It installs fine except that all the previous add-ons disappeared from DAS.
I also tried installing the Addon program from the DVD 3-2013 \stardiag\AddOn_Frame\frameintaller. It starts but than it disappears and it does not complete the installation of Addon installer program I’m assuming it needs to be installed with Admin privileges.
Any ideas, suggestions would be greatly appreciated !
Thanks
Update ** I found the Password for Star user: User$star2004 but it still wont install
hi friends, i have got a hp ipaq 114 and delphi 1.28 is all correct but the software delphi can´t see the bluetooth of the autocom machine, help me please, thanks
Note: It doesn't have SD card ,only has a 16GB hard disk.
Update: online, one year free..3 years Guarantee
X-431 PAD is the new generation tablet diagnostic scanner of LAUNCH for DBS (Diagnosis Based Solution) car system; configured with Windows Embedded Standard 7 OS, built-in printer and Pluggable DBScar connector; With wireless (3G, Wi-Fi) and Wired Network, One-key update and vehicle diagnostic functions (via Bluetooth communication);Extended functions: VGA/HDMI projection, Oscilloscope, Engine ignition analysis, Sensor simulation and test, Multimeter, Battery test, endoscope. Color touch screen, Easy operation.
LAUNCH X431 PAD Feature :
Compact structure ,powerful hardware configuration
Rich multimedia
Twelve groups of data flow oscillogram displayed on one screen
Customized remote collaboration
The first high-end diagnostic product based on the car networking application of LAUNCH Company ,combined with modern communication technology
Diverse internet applications
Various convenient one-key shortcuts
Convenient and flexible in use
LAUNCH X431 PAD Specification :
1.6GHz Dual Core Processor
Memory --- 2GB
Hard Disk --- 16GB SSD
Battery --- 7400mAh, 7 hrs
9.7'' TFT IPS Wide Screen
1.3 million pixels (640 x480 resolution) camera
High speed thermal printer
VGA&HDMI --- PPT/TV
PLEASE PM ME IF YOU ARE INTERESTED UPDATE ONLINE IF YOU ARE IN USA WILL UP DATE BY CHANGING YOU I.P ADDRESS WITH VPN SERVICE
ANYWHERE ELSE IN THE WORLD DIRECT UPDATE ON LAUNCH WEB SITE
Hi there would you be able to point me in the right direction please i need to know what software i will need to do diagnostics and sps programming on Chevrolet NAO i have an MDI but Chevrolet Tis Europe don't cover USA...I would really appreciate l if you can tell me what software i will need thanks you for your support keep up the good work guys....
![[Image: 2mebf5u.jpg]](http://i40.tinypic.com/2mebf5u.jpg)
![[Image: 9pnbj5.jpg]](http://i41.tinypic.com/9pnbj5.jpg)
