good night, someone can help me, I have Ssangyong scan-100 equipment is possible by working with daewoo should I do? it is possible? I have to buy something? thank you
Hi guys i am looking for alldata 10.50 dvd files for both domestics and imports. i got the install app but no dvds.anybody can help me please!! thanks in advanced!
Have a OPCOM interface which does not communicate with the car.
On PCB: OPCOM.5 / 2007-12-10
Did find a schematic on the forum but is not exactly this device.
Mine has an additional MC33897 chip on board which is not on the schematic I found, but still I got the idea how more or less the circuit is built.
Tested on workbench and can see transmit data to selected pins.
My gues is that the data recived back is not arriving at the processor. Will test some more.
I have 3 LED's on the interface:
- RED = Power
- Green = TX from interface to car
- Yellow = ??? Is connected to pin 43 of PIC processor.
Please tell me what the yellow LED is for. Is ON as soon the notebook starts a diagnose session and stays on.
Also if you have any additional info about this type interface... is welcome.
Hi,
i have a 523 '07 N52, with MIL on (only 29F4-29F5 codes at 2400rpm) every 40-50Km.
the cats its okay, and the exhaust emissions is very low....(003/018/1002)
the O2 sensors pass the test and the two before cat sensors have
2.02v and the two after have 0.72v & 0.16v
Dealer database with the diagnosis (if VCI).
Contain a description of the maintenance and repair operations, circuit troubleshooting, and diagnostics, electric circuits, connector pinout, transcripts of diagnostic trouble codes, layouts and fuse grounding points. The literature on repair Kia provides information on disassembly, assembly, adjustment and configuration of all components and assemblies of cars, presents the technical data, dealer information on repair and diagnostics of mechanical and automatic transmissions, the necessary special tool, as well as other useful information for the repair.
In Repair Manuals are Kia cars and light commercial trucks 2011g.v 1990.
A service information in pdf format on trucks Renault: MASCOTT, MAGNUM, MIDLUM, PREMIUM, KERAX etc. there are few and buses. There is guidance on the operation and maintenance, labor hours, repair manual - there are engines, gearbox, axles, electrical components (ABC, ASP, suspended), electrical circuits (electrical installation, with all the plug pinout).
The guy i took my car for service today, showed me his star diagnostic set.
The cables etc, and one old IBM laptop (with pentium III) with serial port.
The software's version is from 2007.
He also told me that when he updated he changed the hard disk.
Doing some googling i found that there are hard diks for sale formatted for IBM T30.
Also it seems that MB has a new diagnostic called Xentry (or is it the same thing ,just renamed?)
My question is:
Can i update only the software in the laptop without changing the hard disk? (is the update floating somewhere on the internet?)
After info on Ford IDS. Will it work for Australian Ford models- Falcon etc. Also will it communicate with Landrover Disco2, mostly to clear SRS light. Most after market tools wont. Also the chinese have two versions. One with magnesium case, and one with plastic case, for the extra cost is it worth buying the magnesium case model? are the internals different?
As all of us know that most of the chinese autocom clone do not contain a chip named M6636B.
As far as I know this chip is responsible for communication protocol used in mostly FORD cars.
I am looking for a realible supplier for this M6636B chip.
Anyone has idea where to buy it ?
Ps: I used google and found some, but minimal order quantity is 100 pcs
Can anyone help with an immo off solution for a 2004 Dodge Ram similar to Viper V10 engine? If you think you can PM me for any details you need. Would be much appreciated
while searching the internet for the problem of my sprinter 314
find some ppl saying that my ecu the data (in my ecu ) is not in eeprom but in
flash ab28f200 chip
while both immokiller software and the sprinter start error software claim to clean
immo if i read both the files from the immobilizer mc08hc and either 24xx or 95pxx in ecu
and clean the file using the softwares (immo & start error ) and then reprogram both ecu and
immobilizer with cleaned files
i think the softwares will not be able to make the trick since they dont deal with data in flash (they deal with data in eeprom 24xx and 95pxx ) ?
can i just send the original immo file to read the pin code for me ??
there is alot of smd 8 legged ices can one of them be the eeprom despite the fact that the numbers they are carrying are not indicating they are eeproms ...is there any sort of masking here ? and if yes what i am going to do to know which chip is the eeprom ??
i uploaded both the immobilizer file (mc08hc) and the ecu picture
Hi there.
Can anyone help me to let me know what do i have to do with this proble.
I have A-CLASS 168 170CDI. when the car is cold i can start engine on and when the temperature goes about 30 degrees Celsius the automatic transmition goes in emergency and when i turn egnition off i cant strat the engine on, and the foult code is: component y3/7s1 (The starter lockout contact is defective) can anyone plzzz help me what is that coz i havnt see this before and what to do?
Thx
Bonjour, je suis à la recherche de Xprog-box 5.3.5 qui n'est plus disponible en téléchargement, j'ai fais la bétise de mettre à jour en version 5.3.11 et depuis mon Xprog-m Rev E ne fonctionne plus, la seule solution étant de retrouver cette version (5.3.5) pour tenter une récupération du firmware.
J'aurais bien reprogrammé le Atmega64 mais vu que mon Xprog est HS je tourne en rond.
Merci beaucoup pour vos futures réponses
Hello, i'm waiting for Xprog-box 5.3.5, at this day it's not possible to download it, thanks
I was wondering is it possible to download new original software in this ECU with Diagbox 5.02 and clone interface? It was asking me a CD or a server download and I don't have a CD and I am also positive that any online server connection attempt will result in blocking my software (maybe even interface?)
Year / Date: 2012
Version: 01
System Requirements: Windows NT4.0/Windows 2000/Windows Xp Professional / Windows 2003
Supports 64-bit systems: None
Language: Multilingual (Russian present)
Description: The Information Base (manual) car repair Concern VW AG. Contains a description of technology of repair and car maintenance, electrical wiring diagrams, standard time on the work performed, etc.
This program is not designed for use with diagnostic adapters.
Extras. Information: This distribution contains all the necessary components for installation: 3.9 setup, 3.91 update, 4.0 update, the SK Base01.2012, serial numbers, key generator, installation instructions, as well as three files with a possible solution to install on Vista and Windows 7. All components are easy to install and require no form of additional programs.
Year / Date: 2012
Version: 01
System Requirements: Windows NT4.0/Windows 2000/Windows Xp Professional / Windows 2003
Supports 64-bit systems: None
Language: Multilingual (Russian present)
Description: The Information Base (manual) car repair Concern VW AG. Contains a description of technology of repair and car maintenance, electrical wiring diagrams, standard time on the work performed, etc.
This program is not designed for use with diagnostic adapters.
Extras. Information: This distribution contains all the necessary components for installation: 3.9 setup, 3.91 update, 4.0 update, the base VW 01.2012, serial numbers, key generator, installation instructions, as well as three files with a possible solution to install on Vista and Windows 7. All components are easy to install and require no form of additional programs.