I need file service and these services STAGE 2, POP AND BANGS ON SPORT MODE ONLY, VMAX AND SPORT DISPLAY FOR 91 OCTANES for this car BMW 430I 2017 2.0T
HI THERE Annyone can help me fix this car
after try with im508 make second key tool faill
now i have only eep from cas
i try with other flash from same cas and car start but elv is locked
i have avdi abrites ori and xhorse keytool plus
I am selling my KTAG clone I bought from cp2010 (EU Version, purple pcb) . It comes with firmware: 8.000 and software: 2.47. It only works with internet connection.
It is fully working and in good condition. Used it maybe 15...20 times.
Just interface, no cables or adapters.
hello everyone, i have a corsa with bad ECU can i get one from Junkyard and do IMMO OFF on this ECU?
If it is not possible to do IMMO OFF can i get the security pin from the file of the junkyard ecu?
Thank you in advance
Hello guys ,
I am pretty new to the forum but i am very fascinated about the amount of info that i get here .
I have searched in the last couple of days a solution for my problem but i cannot seem to find one.
Recently a friend of mine bought an VW Touran 2.0 TDI from 2011 and we find out that the odometer was manipulated and the DPF was removed .
I have tried to find out the real millage of the car in the ECM (EDC17C46) with Odis and Odis engineering but with both of them i cannot seem to find distance driven. like it was removed . and the car is a manual one to so no gearbox data.
Now i want to bring it to the Original state with the real millage and active DPF
Does anybody have a solution for me ?
THANKS !
HI. I need your help .
I have a Ducato after crash.
Fiat ducato 2.3 2021. Automat gearbox zf 9hp.
After a collision, the gearbox controller does not see the gear selector position.
The errors in the transmission controller are U1465 and P0708.
You can change the gearbox operating modes but it does not see the selector position. Fuses ok.
Please help.
Please after fail programming the HU_ENTRYNAV2 with ista, I tried with e-sys but every time i take this message : HU_ENTRYNAV2_0x63 not accessible cause could not be switched to parallel programming mode
Please can help me anyone via remote acces ?
e-sys 3.35.3 icom Many thanks in advance
Read SVT after TAL execution started.
Read SVT after TAL execution finished.
<>
Read SVT before TAL execution started.
TAL execution started.
<ExecutionID=2024/11/16-19:03:17.453>
<[] prepareTALExecution started [PROGRESS]>
<[] prepareTALExecution finished [PROGRESS]>
<[] prepareVehicleForFlash started [PROGRESS]>
<[] prepareVehicleForFlash finished [PROGRESS]>
<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_ENTRYNAV2_63_ETHERNET_63> [DIAGSERVICE]>
<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_ENTRYNAV2_63_ETHERNET_63> [DIAGSERVICE]>
<MCDDiagService<id=230900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=DSC - DiagnosticSessionControl, description=error: timeout, link=HU_ENTRYNAV2_63_ETHERNET_63> [DIAGSERVICE]>
<MCDDiagService<id=242900, job=com.bmw.psdz.jobs.common.MCD3_ActivateProgModeCascade, service=RC_SDB - RoutineControl SetDefaultBus, description=error: timeout, link=HU_ENTRYNAV2_63_ETHERNET_63> [DIAGSERVICE]>
<[] Activate programming mode was not successful for: ECUId:HU_ENTRYNAV2_0x63 [WARN]>
<[] ECUId:HU_ENTRYNAV2_0x63 not accessible cause could not be switched to parallel programming mode [WARN]>
<[HU_ENTRYNAV2 - 63] ECUId:HU_ENTRYNAV2_0x63 not accessible cause could not be switched to parallel programming mode [THROWABLE]>
<[] finalizeVehicleFlash started [PROGRESS]>
<[] finalizeVehicleFlash finished [PROGRESS]>
<[] finalizeTALExecution started [PROGRESS]>
<[] finalizeTALExecution finished [PROGRESS]>
<TAL execution finished [TAL_EXECUTION_FINISHED]>
TAL-Execution finished with status: "FinishedWithError".
TAL execution finished. Duration: "59s".
<>
Read SVT after TAL execution started.
Read SVT after TAL execution finished.
there is no way to conntact them ..... Anybody knows how to force stellantis to move?! We are not just one shop, there are more more more shops in EU that cannot acces technical documentation and diagnostic (witech, diagbox) due to accounts on hold.
Hello maybe samone knows which smd leds i could use for turn signal repair in headlamp front w204 ils, i used for repair yellow leds and they were not bright enought and burned in 4 months
I buy this Citroen thinking that will be better than the old one.
Engine RHH 163 HP euro 5.
Manual gearbox.
I replaced thermostat, temperature 77-79 degree (same after replace) almost all time 6 line In dashboard.
Compression on cilinder from 21 bar to 24.5bar
All injector replaced with remanufactured by factory. Coded with lexia. Adaptation reset.
Still don't do active strategy for injection.
Car consume like one automatic (old car euro 4 the engine).
Dpf it's there, nothing removed from car
When I accelerate, I have some white smoke (seen in car light from behind).
Whe I accelerate the rpm indicator it's make some small jumps up and down. 20-30rpm.
Im selling access to mitchell estimator the newest ultramate its simply to use and guarantee for 12 months
i have 2 options
1. price is $100 u will be provided with username and password but your access will be with other users so u will need to create your own profile and always will need to select hat everytime you create your estimates.
2.price is 225$ this is your account only nobody else has access to it.
Hello! I need someone to help me with this stage. And tq monitoring off. I made a stage but i am not satisfied with the result. i will atach ori and mod. Thank you
.
enso 11702-19220 
