Hi, so I have a problem and I dont have experience with this ECU. For context is a Sismos PPD1.2 03G906018EM 5WP45562 AE, from a Passat 170cv.
So I took the ecu out because the car is stupid now and dont start when engine runs hot so I was going to try the HotStart fix to see if was an injection problem.
I used my old KTAG (ksuite 3.xx, last version, never failed me), so I made the BDM connection, power and grounds by pin and read the ECU no problem and wrote the a new flash, but I didnt use the original flash the I read before, I trusted a friend and he gave me a file for a stage1 with th mod I need. Ktag wrote the file no problem.
I plug the ECU in the car and it didnt start, obd diag didnt recognize the ECU, so I went back to the bench made all the connection but now eeprom reads and writes ok, but flash when reading, at the end when you go to save gives "Checksum Error", and when writing as soon as you select a file gives the same error and aborts.
So I went on configs of Ktag and disabled the automatic checksum and I can read and write if I skip the checksum. So I flashed the original file but car still cant recognize the ECU and I dont know why the Checksum error happened because I checked on Winols and checksums is ok. It started after the initial flash write and I cant fix it.
Can I assume the ECU died? Or is there a fix /recovery process?
Because now Im afraid because I dont know if the file my friend gave me fucked with processor or it was the ktag that killed the unit, it never failed me even in densos and new generation ECU and I did this same unit a few years back (FAP EGR) with a kess clone and worked fine.
Hey, i`m looking for solution for UREA delete in DCU on this ford ranger. We have problems doing reset on the ad-blue with all the diagnostic tools we have tried. Is there possible to do delete without?
VAG PCR2.1 IMMO SUITE
Tested on REAL CARS.. NOT on a database of old immo files..
Version: 1.20
1. Real garages only please.
2. 150 GBP = pounds sterling
3. offline tool
4. works on all 2048kb & 2176kb full flash (NO OTHER TOOL ALLOWS WORK ON 2176kb FILE SIZE)
5. Allowed DTC Removal (NO OTHER TOOL ALLOWS DTC REMOVAL)
6. Allowed powerclass change.
7. Allowed fix flash checksum.
8. Allowed mcuid lock option or native IMMO OFF (NO OTHER TOOL ALLOWS BOTH TYPES OF IMMO OFF)
9. Amt Bst bench tool is recommended for pcr.
10. once tool is activated no refunds... this is digital download activation.
NEW video's link pass: RB
Fully and properly tested on real cars by me...
If any of these video's or pictures appear anywhere else they came from here
hello friends would need some help with this
mercedes e200 bluetech
2015 2.1 100kw om651 engine
automatic transmission with delphi crd3.7A
I need DPF,EGR and ADblue off
thank you all !
Hi, can someone help me with a diagram for BSI? I need information on where the wires responsible for the sliding door information are located, the car doesn't have them but shows the information that they are open... Because of this, the central locking doesn't work, there is no option to code this...
Citroen Jumper 2006r, Relay III, Puma 22dt 100cv
VF7YCAMHC11213865
Hello everyone,
First of all I would like to thank everyone in this forum for all the years of knowledge received. You have been extremely valuable.
Now to the subject matter. I have a 2021 Silverado with missing features on the ipc such as sport mode , oil temperature and speed alarm.
I would like to know how to activate them. I already have sps vin for this vehicle as a slot on techline connect and gm dps installed with type 4 option available.
However I am lost on how to get to xml and calibration files and how to edit the files.
Do anyone have 3D models for VAG parts? I would like to modify a pulley to make engine swap easier to T3 transprter.
I looking for a pulley with part number: 028 121 031 E
Hi,
I have Ford Fusion, 2019 from Canada. I was able to make all the neccessary taillight and SYNC3 conversions to EU, but I struggle with enabling PL language in IPC. I know that I will need to reflash IPC with correct files and I know that I can write Mondeo MK5 files to it. But I can't find correct VBF files anywhere. Not knowing the correct file names is another problem.
Right now I have:
Part number - JS7T-14F094-HA
SBL - FS7T-14C025-HA
Calibration - KS7T-14C088-HD
Strategy - KS7T-14C026-HE
Can anyone help me with correct VBF files to flash IPC in order to get European languages active in it ?
![[Image: 1-20.jpg]](https://i.postimg.cc/vZ5TY31s/1-20.jpg)
2033 
