CAUTION —
Risk of irreparable damage.
Touching an incorrect pin can cause severe damage to the circuit board.
Ensure that the battery connector is positioned correctly.
For battery fitting and removal, see 1 689 979 856.
Initial commissioning of the storage battery:
1. Switch off the KTS 650/KTS 670/PIWIS.
2. Insert CD 1 687 005 037 in the DVD drive.
3. Switch on the KTS 650/KTS 670/PIWIS.
The KTS 650/KTS 670/PIWIS boots from the CD.
4. Follow the on screen instructions and start the calibration by pressing any key.
After successfully reprogramming the Smart storage battery chip, the KTS 650/KTS 670/PIWIS is
switched off automatically.
5. Remove the CD and switch on the KTS 650/KTS 670/PIWIS.
Hi.
Today i`m trying to activate DRL on my Corsa C , z12XE, 2001, hatchback with Op-Com.
I have original Carpass.
On Body control Module....-.....Variant Configuration....write security code...-...Enter.
Security Code not accepted.
Op-Com with FW 1.39 software 08.2010.
Upgrade FW to 1.43 no chance
Upgrade FW to 1.44 no chance
Upgrade Fw to 1.45 and software 120309a....no chance
Negativ response.
The car start with no error , no problem.
I have no ideea how to proceed.
Litle help realy apreciated....Thanks in advance!
hello everyone
i have a problem here if anybody can help me i will be thankfull
i bought c3 multiplexer with external hard drive through my friend who have account in chinesse website
i got it already and it is work fine suddenly that exrernal hdd not working
i already copy that SC-DAS-1207.vmdl virtual hdd with size 68.GB size with i dont have and make this file not working is SC-DAS-1207.VMX configuration file
pleasssssssssse help thanks in advanced
I bought the wrecked car, given that the previous owner put any product to the fuel tank that damaged the diesel.Já had to replace the sump pump system, sent to repair the high pressure pump and changed the 2sensores ramp because of the fuel injection appears to me the code P1181 mistake.
is a normal condition when the key is turned to the light switch does not delete?
It is tested with that produced no immobilizer and so has this P1181 error.
Someone knowledgeable in Hyundays that can give me some tips?
I'm having problem with w211 270 cdi . sometimes goes into limp mode on the motorway. It only happens when the engine is warm.When i turn the engine off everything is OK .
I plugged star in and it said fault code 2346-002 "check system 'Exhaust gas recirculation control'. The air mass is too large"
hello,yes im new here but ive been lurking for a while,learning and trying,,let me tell you guys what im doing,,
im adding every avalible option to my 2008 3500 hd ext cab duramax dually,im using gm factory parts , heres a list
1.power windows
2.power locks
3.power seats with katskin leather
4.remote start
5.navigation radio
6.rear view camera
7.back-up sensors
8.power adj pedals
9.homelink
10.intergrated trailer brake controller
11.exhaust brake
12.DIC
13.automatic digital HVAC
14.power tail gate latch
15.steering wheel controls
16.rain sensing wipers
17.bluetooth
18.4x4[in the future maybe]
everything is plug and play [and alot of labor to add factory wiring] and most things worked from day 1
but i still cant get the power door locks to work,
ive got a tech2 and mdi scanners
ive tryed using a BCM from a different 2008 truck that has all options and everything works-but locks the radio[yes i can clear that]and locks the xm module,
ive got 3.2008 tis2000 downloads,but my truck was built 3-08 and it doesent see my vin
i need the last tis2000 dvd updates 8.2008 and or 10.2008,[id really like dvd's but i'll try downloads too]
ive tryed tis2web-but since my vin is in GM's interface as a WT truck it wont alow me to add options,,
but using tis2000 ,i can use the ''replace and reprogram'' fuction ,then i can reprogram the BCM to add everything i need and the tis2000 doesent care what my vin# is,
I want to clone edc16c3 from pug 307. My ecu is not good I got one on ebay. can I clone this by bdm? i have fgtech and bdm frame with bosch probe. is it as easy as take read from original ecu and bdm it to donor ecu?
does bdm transfer all necessary files for the car to run? immo?
![[Image: 78626120131110.jpg]](http://www.hostingpics.net/viewer.php?id=78626120131110.jpg)
))))))))))
