Hello.
I need for BMW E46 with ecu DME MS42 5WK9037 SIEMENS 2.2L the flash of ecu and the flash from EWS.If I have these,after I make keys.
The ecu has 29F400BB eeprom.
Someone try to make chiptuning and destroy the car!!!
Thanks & Regards!!!
Hey. I am looking for documentation on the crane MEILLER TYP-RK20.70 which is installed on the Truck VOLVO FH12. I would really appreciate the documentation and repair scheme.
I took a reading from my 110bhp octavia mk1 tdi(non pd),for fuel to injectors.
It reads as :cyl 1= 0.09mg/H MIN=0.09 MAX=1.36
cyl 2= -0.12mg/H MIN= -0.71 MAX= -0.05
cyl 3= -0.02mg/H MIN=-0.66 MAX= -0.09
cyl 4= 0.02mg/H MIN=-0.85 MAX= 0.02
Can anyone tell me which injector/s are ok/bad?
I read that the injector with greatest deviance (ie cyl1=1.36),is correcting for the cylinder immediately before that stroke.Is this true? Does this mean injector 2 or 4 is bad? any help appreciated
thanks
Hi. Will someone please help me, I need to know where I shall connect key1 and key2 wires on connector from my radio Eonon gm5161 in to the steeringwheel (14 pins) connector.
I would be very happy if someone could give me advice. Thank you in advance. forgot its a Ford S-max 2007
Hi friends I want a real off my computer edc16c39 iveco, I perform a reading bdm I eeprom is the flash, would anyone sil means you like me to release me?
apparently it would be in the flash the undersigned?
Hi friends I want a real off my computer edc16c39 iveco, I perform a reading bdm I eeprom is the flash, would anyone sil means you like me to release me?
apparently it would be in the flash the undersigned?
i have problem with a w211 ezs not open and don t turn the key.the key is ok the one of 2.i take a ezs used and i check the flash is ok.the eprom i write to used but i want to check my file eprom if it is ok.i see some 4 4 4 and in other eproms i don t see in first lines,thanks for help
I have mercedes benz w221,the old control unit was dead,then i bought another control unit and renewed it,so i need to adapt it with a car,does it need scn coding ?or i will just do initial start up offiline?
Have just used the new ford software from cryptoworks to do the new coded access systems and works fine job done in 5 mins added new keys on keyless system the new calculator works fine first time did job on 2013 plate focus
Welcome. I need a calculator outcode InCode for Ford. What do you recommend and where most preferably buy. Can somebody also fast for me outcode InCode?
I don't know if this is the good forum section (I hesitate with IMMO section).
I have a problem with a bsi, I know how read the 95040 chip on the bsi, but I had to break the top (plastic).
Did you know if there is an other method to read the chip (in the aim to have the password) ?
I already tried with a BSI from valeo, It worked before I removed and reinsert the chip, and now it's out of order, is there an other other method to not destroy the BSI ? (I have an other one BSI)
Thank you by advance (and sorry for my english, but I work on it)
I am looking for some ideas to resolve a vehicle I have in my workshop.
It is a Fiat Scudo 2006 with a 3 plug Bosch ECU EDC15C2 Code 0 281 011 343
It has the error "Permanent Fault. coded anti start operation. function faulty" when read with pp2000/diagbox
I read the 35p08 with a Gq-4x, and I have attached the bin file.
I then used Universal Decode 3.2 to attempt to remove the immobiliser.
I could not write the data to the 35p08 - it would only write the first 4 lines.
So I removed the 35p08, and replaced it with a new 95p08 which I can read and write to fine.
Now this is what confuses me:-
I write data - I unplug the GQ-4X, I read it again, it is still correct.
If I put the ECU into the car, and power it up - when I read the data with the GQ-4X it is now different. Bin file attached
Same goes if I try to start the vehicle - it alters the data. Bin file attached
Is this to be expected, or is this ECU corrupting its own immobiliser data on the 5p08 ?
I would love to resolve this vehicle as it is a grate learning tool. I do not understand how the immobiliser system works!
need help with byteshooter basic
i try to read car with changed wires and one component shoot
here is pictures from board if anyone can tell me what is it to change
Thanks advance
Hello
I have a problem with airbag from Renault Megane.
It's Autoliv 550 80 36 00 7700437477 AL
I tried to clear it with CarTool but that didn't work.
Thanks in advance
We are selling Mercedes NTG3.5 NTG4.5 NTG4.7 NTG5 NTG5S1 NTG5S2 COMAND NTG6 NTG7 MBUX newest map update data and activation pin codes for all systems and regions (Europe, Russia, Africa, Middle East, North/South America, Japan, China, Taiwan)
Also video in motion (TV free) software solutions for Europe, USA, Japan, China, Taiwan region Mercedes vehicles. Just USB and SD card is needed
Hi
I have China clone FORD-VCM-OBD, on the PCB is't missing components:
u1, u2, q8, r9, d3 Someone having original Focom, could check what are the elements?
![[Image: DLM-714x408.jpg]](https://i.ibb.co/h9qvNx5/DLM-714x408.jpg)