somebody has videos repair common rail injectors? whoever can post here? I'm starting to repair common rail injectors. and we know that all possible information is valid for the technical improvement.
ps:
can be manual, handouts, courses ... anything related to repair common rail
I found the original dump from vitara,ecu and immo also i read and key with zedbull
The dedbull gave me this code:
DATA: 7E6C1408400000000076987E0000
TYPE: 4C TEXA WR
I want to ask if you can sync these two files lest he finished and suffering with this car
Having problems getting the first version (5.02) to install. Read through all the posts and still no clear answers. If anyone can give a definite answer to the following question it may help.
1. Has anyone got Diagbox running on VMware Xp (pro), Sp3?
2. Do you need to have Lexia and PP2000 installed BEFORE and then upgrade to Diagbox?
3. When you mount (ISO) Diagbox 5.02 there is a folder called 'Archives' containing 3 Zip files (lexia, PP200 and pp?). Should these remain in that folder left as a Zip file. Or should they bbe Unzipped/moved before mounting?
The stage I get to is; software installs, patch pasted in c:\AWRoot\bin\fi\cache and says 'successful'. Tries to load Lexia and reports 'error you must re-install diagbox to reactivate'. Its as if it can't find Lexia? On Scary video's he has Lexia/PP200 showing as image file on Desktop, should these be mounted before installation. Thanks..
I have a "little" problem with my C4 mux, and I have not been able to find any other with this exact problem. Everything's working fine when I use the cable connection between mux and laptop. But the wireless card just wont work. I bought this on eBay for over a year ago, from China. Until desember last year it was all good. But then the hdd broke down, and I bought a new hdd from china, preinstalled with all software. The first time I connected the mux with the new hdd DAS automatically asked for a software update for the mux, and at the time I didn't know I probably shouldn't have accepted. It started to update, but because I didn't have any batteries installed at the time, the update stopped half way through.
Later I learned that batteries need to be installed during software update, and I managed to run the flash, boot and cs_csd file successfully. As mentioned the mux works perfectly connected to cable connection. But when I press "Info" button on mux, WLanMac shows this: -:-:-:-:-:- And when I open the Register/Configure section in SDconnectControl Panel, I only get three lines at the top showing the registered number of the mux, Serial number of mux and Wlan Mode - No Wlan. Nothing else below these three lines.
I have tried pulling out the Wlan card from mux, and installed it into my Laptop. It works perfectly there, so probably nothing wrong with the Wlan card. Also, when wlan card is installed into mux, "Status led" flashes slowly. But nothing at the "Activity led". If this had happened on my laptop, I would have guessed there was some driver issue. Might this be the same case on the mux?
In general, the issue of such a plan. Each auto group PSA has a 4-digit code for the prescription of key activation immobilizer ... well, in general, you get what I mean.
So, some friends are doing a dump eeprom. Immediately raises the question of how to make it? It is clear that the programmer, but it can give the programmer the scheme which, whatever it was possible to gather and enjoy!
Well, let's help the programmer, collected, stripped dump EEPROM. I'm going to bin file. What's next, give a tear from this dump VIN for cars. That the people using it. Do not tell me that? What is cFosSpeed. There is what the calculator, ICC but he has such a value that ah ah ah. Tell me, eh?
The bottom line:
1. Help with the circuit programmer for EEPROM dump auto group PSA and if you can some instructions how to make it?
2. The program for reading this dump and pulling out his PIN. Thanks in advance!
If not please recommend a good device and what software version I should choose. Is it possible to order devices which can be updated/re flashed or secured memory which can't be deleted when connected to internet?
I am looking for Cat ET software. I dont think that the version is as important for right now. Can sombody help me with this, or point me in the right direction. Thanks.
hey everyone im after a cracked version of vagcom 409.1 , ive brought a ebay lead from china and i really want a cracked copy please , ive looked on here already but still no good
I'm trying to read the processor motorola MC68HC08AS20 with the UPA, but always asks me the error message "Device not respond."
does anyone know what the reason for this be happening?
thank you very much
I have the original mercedes part D3 mux, does not work with RS232/485 converter cable
Which cable you need use to connect it to a laptop Rs232?
Maybe someone has a cable schematic.
Sorry for my English and thanks for any help.
Regards Pawel.