Year / Date: 01/2013
Developer: BMW AG
Language: Multilingual
License: Freeware
Description: BMW ETK contains the full range of parts offered for sale by BMW Group and is intended to facilitate the retrieval of necessary spare parts (car parts and motorcycle), supplies and accessories. To do this at your disposal a variety of search functions, such as searching by name, by part number, etc. In addition, the system offers detailed information on specific details, as well as the ability to create so-called parts list of found parts.
Extras. Information: Installation BMW ETK:
1 The name of the computer should be in Latin.
2 Ports must be set in 1027 and 1028 during the installation, in the lower fields will already be 2024 and 2025.
3 server addresses blank.
4 Catalogue of RR is set if a password oxford12.
5 Market choose Eastern Europe.
6 Firm and business partner ID 1 and 1 (in both fields).
Install a DVD or a virtual drive with the loaded
Hi,
Please can somebody help me to immo off for this peugeot 406 ,
ECU is Bosh 0261204066 MP5.1.1 Essence , car have keyboard with code , but I need to delete immo.
EEPROM is 93CS46 , dump attached
Can someone try to read pin code from this dump?
Vag Can Commander show me 31777 in auto read, and 1538 from immo read section. But I'm not shure it's correct.
I installed xentry das 11.2012 and use compact4...
In call.ini it's Part_T...
hen I want to connect to vehicle, with DAS ( stand alone ) the comunication error appear that: fault (1.18)-9.890
and when I try to connect with Xentry the error: fault (1.2)-2.503.13003 appear...
Hi, can someone help me to change hours of this komatsu dash?
Original hours are something between 18000-18400hours and i need around 9000hours, Here is dump from S190 (s29190) eeprom .
If someone can post power pinout or schematics so it is also welcome.
HELLO i have problem with steering angle bmw 5 sery 2004 fault code( 6136 sensor supply engine position and 614a motor position angle not initialization )please all member help .
i have deinstalled the old autocom software 3/2011 and installed Delphi 03/2012 and activated it.
i can start the software but no connection to the vci.
interface connected to obd16 and usb to computer.
Wenn i connect the interface with the obd then the 4 leds are short on -red- , then it's all over.
I have purchased a used cluster and just want to try and clarify the swap procedure.
Once I have swapped the LED's and installed a blank M35080 chip, can I just plug in the modified cluster and LCM and EWS will update the mileage and VIN in the new blank M35080 automatically?
Or should I do a backup with PA Soft 1.4, then do a restore after I install the new cluster?
I dont want to touch or modify my original cluster.
I have a factory VCM that came with my T4 Testbook kit (was used with WDS installed on Testbook)
Since I don't use WDS anymore, I want to use that VCM with SDD V131.00.
The computer sees it plugged into the LAN port, but SDD won't recognize it. What do i need to do, to get SDD to recognize my VCM? Its not a clone VCM, its original.
I looking for a greate but cheap flasher, would like it to flash edc16c39 ecu.
Can a china tech 2 flash T7 and T8 saabs?
i have a Ttid saab, have a galletto master that reads the ecu but something strange happens when
i try to flash the mod file to the car. The flashing seams to go ok. No foult codes but when i check the ecu after its the old software still?
Can the kess clone flash this car? and wich MPPS clone its the best?