W221 with ME9.7 ECU has problem with ignition, only 4 cylinders have ignition, other 2 don't. Thought it was ignition driver chip on ECU board (Bosch 30427) then replaced it, but still same problem. Please advise what I should do now.
hi. a friend of mine has a 2000 seat ibiza 1.9 tdi 90hp. i tried to use mpps to read that cars ecu but i wasn't able... can it only work in 110hp and above? is it only available in bench mode?
thanks
Symptom driven diagnostics. Is that what it means . Can you only read fault codes or interrogate modules by choosing a symptom in the session? The format seems very different to v128??? Is there a help guide anywhere or dose anyone have any helpful tips. It would be nice to have an overview of all modules with a DTC count!
Thanks guys
FIAT brava model 2001 1200 16v engine number 188A5000
the cooling fan is not working i am sure that the problem is the ECU
i checked the fuses ok relays ok grounds ok cooling fan motor working ok antifreeze ok no air inside
is there any way to fix the ecu ?
This is NOT a "Paper Handbook" or " Paper Printed Manual". This is an electronic ebook file under the Adobe Acrobat PDF format .
SOME CONTENTS OF THE REPAIR MANUAL:
- General Information
- Engine
- Transmission/Transaxle
- Driveline/Axle
- Suspension
- Brakes
- Steering
- Restraints
- Body
- Air Conditioner
- Electrical
- Maintenance
- Power Supply Routing Circuit
- Electrical Units
- Super Multiple Junction
- Fuse Block - Junction Box
- Fuse and Fusible Link Box
- Fuse and Relay Box
I need SAAB program. The program is what I'm looking at Installation instructions, wiring diagrams, etc. ... Full Details. I found a program SAAB WIS, BUT the program haven't got enough language. :/
Hi guys,i bought a new car and this is my second tune file.My first modification was to delete dpf with ecusafe and to change dpf pipe with custom one but after this modification car starts smoking at idle.Can you help me to turn dpf off.Thanks in advance
Hi. Using latest vas-pc v.19.01.01 with a genuine vas5051b on a 2012 crafter the attached error appears. Java version installed is 1.4.2.15
Any hints ?
Hi all,
I have one big problem. I hav two the same units from Volvo V50. But one is damaged by short connect and in the middle of pcb is small hole from fire. :-)
That was in car. I have problrm with cloning via bdm. I can´t use power supply in connector. Who know where is testpoints in pcb near MPC?
Many thanks for help
Matias
help me please I use autocom cdp clone + I'd like to know if I can use Autocom Cars + Trucks 2012 and so will my multiplexer and will damage or can I find the torrent link
Hi, have anyone experience with tool Programator BSI in PSA group from Smok? I need some good tool for PSAs BSI.
Second question - where is stored fault history (fault diary) and PIN code in BSI? Is it stored in eeprom as km?
Thanks
C3 head xentry201207 Version DAS is driven.However, do not give the driving Xentry
Error message (1.58642.9500): Slavelnterface 09500: COM port not available for use
Who Please drop us a note if you know how to solve. the same versions as xentry201209
Hello Members!
Today i got a WDD2040411F027292 age 07/2007 that was in a Garage for five years now since owner died. A new battery is installed and the car is fault free but won't start. EIS Start is authorized. In the ME (Engine) SIM271KE20 parameters i recognized that the starting is not authorized because of active Transport Protection, ECU not initialized (activated) and so on. No ECU is exchanged, all original except long time without voltage.
So my question to you is how can i initialise Engine ECU? My equipment:
SDConnect4, Xentry 01-2012 all Addons and working well with Developer Key. I did the relearn procedure for Throttle Body, Fuel Pump and so on successfully, but don't know how i can initialise the original ECU. If i am going into Adaption Offline Section, then Xentry asks for Password i don't have.
Any ideas or help? I appreciate everything you advice!