Dear,

which software/hardware i need to clear the UCH that i can write it new with renault clip?

Thanks for help!

Hi all,

Anybody out there has update the mux via sdconnect? I was updating my mux because the das require me the upgrade the mux in order to use the 9/2012 version. I update the mux via sd connect, upgrade software tab. During upgrade, there is error. I tried upgrade again but it has the error. Anybody experience this problem?
Can I update the mux firmware via sd card? Please help. Thank you

Dear sir,

Anybody out there faced with the Internal Error (3.17)-3.175 on Xentry? Can anybody shed some light on how to solve it? Thank you in advance.

Attached Files

Thumbnail(s)
   

Hello


Does someone know how to change km in siemens ecu from 2.0tdi engine .

eeprom is 95320


Regards

Is it possible to get security pin code for fiat scudo from chassis number and can bsi be programmed using pps?
tia

Hello,
I've bought clone Clip a 2 months ago. Interface working fine but when i open it i saw that on both of pcb's there is a cypress 2131QC usb controller instead of an 2135SC like in oldest version of clone clip. (This chip is 2 times bigger than 2135sc and has a rectangle shape. Could someone tell me is this change make any difference in clip functionality?

Attached Files

Thumbnail(s)
       

Hi,
Help someone off the EGR kangoo 1.5 dci in
thanks

Attached Files

kango 1.rar

65

13.65 KB

Download

hello m8's

i want to know how can i perform oil reset for W166 ... not using Xentry

using the IC in the car

thanks in advance

Hello,

I'm looking for diagbox 5.29

Thanks for any help

Hi,
I have a fatal error message:
Unknown error during init
Is anybody have resolve this issue ?

This is 3-2012
I get this error on SD Connect Fault (1.1)-1.501.9617
Initialization of diagnostic multiplexer failed. ( Circuit 30 / 31) faulty

I tried with fix DAS Bin folder
Re enter key

Any help

(11-26-2012, 11:22 AM)Blacktube Wrote: This is 3-2012
I get this error on SD Connect Fault (1.1)-1.501.9617
Initialization of diagnostic multiplexer failed. ( Circuit 30 / 31) faulty

I tried with fix DAS Bin folder
Re enter key

Any help

Attached Files

Thumbnail(s)
   

Hello

I have modified Cas modul by obd2 of this type of car and after impossible to do any service oil or another ..... Brake and another.

I have don.t change the M35080 because it was a 6 model and it erase very well

I have try manualy with trip button, with Ista too,with autocom too and no result

Somebody have a idea please,,,,?,,,

Thanks for your help

Best regards

Hi Friends,

Has anybody got any experience with using the Dearborn DPA 5 Protocol Adapter.

I have used the Nexiq and so far I am very pleased with the tool.

Dearborn claim that their tool is faster.

Cheers

hi everyone

I need help to put this file in fap off i try in ecu safe but no work.
Any suggestion?

Thanks

Attached Files

citroen c4 1.rar

55

1.11 KB

Download

hello mates,

i need anyone to please help me out on this problem, after activating my DAS Xentry 03/2011, I ran the software for a while, then suddenly I started getting the error "INTERNAL ERROR: (2.75)-3.175. PLEASE CONTACT THE STAR DIAGNOSIS CALL CENTER"

Could anyone please let me know what I did wrong, or whats wrong with my software.

kind regards

hi dear friends i need porsche piwis software i look in forums i find vm version but rapid links are off

please help me...

best regards...

hello everyone trying to install DAS 2011.1 again anyway when i start i get the language selection click next it does a couple of things and the this come up



Uploaded with ImageShack.us

when i click on yes it says this update is not aloud on this computer or something like that and when i click no i just stops what do i do thanks

Hi hope some one can help!!!! Iam running diagbox 6.30 with a china clone interface and all is working great as I've updated it from 6.01 to 6.30 can some one please tell me what firmware version I should be running on a china clone interface please?????

Does anybody have a "carminat 1" cd (maps format sh3) for Renault Laguna 2005r? I need it just to make a clock work properly.

Beware these VMs has protection in the form of a dongle, without dongle the VMs don't work. Hopefully someone can remove the protection.[/size]

Reference manual here:
http://www.volaltd.com/bmw_manual/

ICOM Firmware:
http://www.volaltd.com/ICOM_3.00.45.rar

Attached Files

isss2.48.1.txt

613

4.43 KB

Download

isid_2.34.txt

437

1.41 KB

Download

Hi everyone, I have a Actia Multidiag clone interface with vci A070026, I am able to use it with Multidiag 2010-I and I was wondering if there is any update that I can use with my interface.

Thanks

Hi.

I had to format my notebook and reinstall Autocom. Everything went fine. I've activated it the same way as I've done it before format (it was working normally).

After activating I've deleted Autocom folder from Documents and Settings/All users. It's working, but I get the "first time configuration" message on every startup. Kind of annoying.

Windows XP Prof, SP2.

Any ideas?

Regards,
szejk.

Hi
Does anyone have a dump airbag TRW VW8
3C0909605F

25lc640 original circuit was overwritten by mistake with ff.
I found a bin from other module but after I programmed IS OK...
But vas5051 not want to write coding than new unit.
have any solution? method ?
Thanks in advance

Attached Files

3C0909605F.zip

65

2.46 KB

Download

dear friends i have xentry 09-2012 realese but epc is not work.
when i start epc say it error 451 no valid starkey found for the current programs..

any body helps what can i do

thanks...

Hi All. Can you give me Factory password to clear the fault code.
-Current ECM: C15 Truck (SDP 19059)
- Service tool: ET524288-6-TZ
-Engine serial number: SDP19059
- ECM number: 25686126RA-TC
- Total tattletale: 2191
- Reason: 3
-FLS :2
-FTS: 0
Thank a lot for your help.

Hello!

I'm using Galletto 1260 with MEMS3 in Rover 25, there's memory 29F200.

When I read memory I get file with size 16kb, but this memory have 256kb.

It's possible to read fullflash from this ECU with Galletto?

Regards

Hi guys,

Im having problem after installing 9/2012 version. When I run the DAS, after selecting the car model, it show the mux unit unlock, then it change the padlock lock sign to lock and show a CAL870 fault on screen. Please see the error in print screen. I have replace the files cal.sli and change to read only and it still cant work. Any ideas how to solve it?
Thank you advance. I hope our master out there can share a light. Thank you again

Attached Files

Thumbnail(s)
   

Goodmorning,

i have airbag in object crashed. Please clean my file.

Best Regards.

Attached Files

crash.rar

81

1.14 KB

Download

hello
please help
i need link for download eLearn sw
rapidshare, torrente, or other
can somebody help me

hi, my client lost her remote control for citroen c2 2004 i bought for her new remote original citroen c2 its for c2 i try to program it on the lexia it program but when i press lock button the bsi receive the signal from remote and it make ( tick ) only 1 time and after nothing , but when i close the door from insid the car from the inside button at consol and press lock or unlock the bsi make (tick) when i prees lock or unlock , so can anybody help us ?