To obtain your registration code, please send an email to [email protected]
 
Jaguar Anyone know how to change gear ratio in Egs51?
Posted by: adam699 - 11-21-2012, 01:17 PM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (1)

????
Anyone know how to change gear ratio in Egs51?

Print this item

Mercedes Benz xentry 03.2012 automatickly disables wifiadopter
Posted by: jurxx - 11-21-2012, 12:44 PM - Forum: Daimler Group Mercedes-Benz, Smart Discussions. - Replies (6)

Hello again.

so i scraped the original installation, and used one of my own installation backup drives - adopted to original tablet using ads-tec drivers, but there is a problem - automatically disables wifi - iv been fighting for 2 days..

renamed all networkfilter.exe files, disabled hardware assistant, but no luck, OK now i can enable it and it stays on, but that is not a solution...

where to look next?

Print this item

Opel Astra G Z18XE - Eng ECU virginal...How to??
Posted by: Sparky001 - 11-21-2012, 12:41 PM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (3)

Heya all, Fing32
I have found a few Eng ECU's for VZ commodores & Astra G's that have not been "Divorced" from existing Immo, cars. Is it possible to make them "Virginal" without the original vehicle they came out of??? Have sorted out my mates Tech2 to program them, but are currently unable to reset without original car.

Cheers Beer Beer Beer

Print this item

AA Iveco Iveco Daily immo off
Posted by: kos600 - 11-21-2012, 12:23 PM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (6)

Hi all! 0281012193 ECU EDC16, help disable immobilized


Attached Files
.zip

edc16_iveco_95640.zip

144
1.48 KB
Print this item

Nissan 2011 Nissan patfinder airbag clear crash
Posted by: samyboy - 11-21-2012, 11:21 AM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (1)

Hello every one .
can somebody please clear crash data from 2011 nissan patfinder airbag modul
98820ZL00A with 93c66 eprom inside


Attached Files
.rar

98820ZL00A_crash.rar

64
342 bytes
Print this item

Toyota Looking for virgin ECU Toyota lexus 16 bit and 32 bit
Posted by: hauwkee - 11-21-2012, 09:13 AM - Forum: Automotive Activation Key Codes Requests. - Replies (3)

hey i m looking for virgin dump for toyota lexus
file called 16 bit and 32 bits or ecu type 1 and 2

Print this item

Fiat examiner 8.20 witech
Posted by: billagassi - 11-21-2012, 06:04 AM - Forum: Automotive Software. - Replies (17)

Hi I'm Andrea from Italy sorry my English
I don't speak English
this is my first post (wow)
if anyone is interested I have a vmware image for examiner 8.20 (witech)
thanks particular for system administrators Fing32
this site and 'fantastic !!!!
Hello everyone good and badCheer2
Andrea

Print this item

Toyota Air Bag Corolla 2006 XEI - Brasil
Posted by: Gargem - 11-21-2012, 05:04 AM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (3)

Hello,

I need a file from the memory of Ari Bag 2006 Corolla xei

TRW 21349-102
TOYOTA 89170-02530
W8 DP P / T

Note: When removing the memory it broke and I can not remove the file Crash.


Please help me out.

Print this item

Mercedes Benz need bdm or mpc MERCEDES SPRINTER 315CDI
Posted by: qmax2 - 11-21-2012, 02:22 AM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (3)

HI
i need original files to mercedes sprinter 315cdi
0281013810
1037381129
sw1037505811

thanks advance

Print this item

AA Bosch-logo [REQ] Bosch esi[tronic] 2010/1
Posted by: kato - 11-21-2012, 01:34 AM - Forum: Software Requests. - Replies (6)

Hello all members! Tup

Is there a kind soul out there who has and can upload or provide me with links to esi[tronic] 2010 ?? Pc
ofc. with keygen/patch Kolo

IF possible, .torrent is preffered Smile

Thanks in advance

Print this item

  Need dump airbag Jaguar XJR 2W93 19G275 AC
Posted by: krzy - 11-20-2012, 11:47 PM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (1)

Hello, i need dump for this sensor, memory S221 (93c56), crash or not crash preferably both. When i tried to read it with VP480 it was empty.

Thanks in advance

Print this item

  Pdtdi engine hot start problem
Posted by: tenen_2004 - 11-20-2012, 11:22 PM - Forum: VAG Group VW , Audi, Seat, Skoda, Bentley Discussions. - Replies (7)

Hi,

I have a customer having poor hot starting on his pdtdi (1.9) engine (vw).
I read many forum and everybody say it is a software problem.
Few weeks ago I read some information for this problem how to solve it VCDS ?
Is it possible to solve this problem with VCDS ? or just remapping ? 533

Print this item

Mercedes Benz Mr Zolookas guide?
Posted by: geekfreek - 11-20-2012, 10:52 PM - Forum: Installation Guides, Procedures & Tutorials. - Replies (1)

Anyone have a working link too, of know the whereabouts of Mr Zolookas Newguide 2i ?? TIA

Print this item

  Useing KTS device as modul only?
Posted by: kato - 11-20-2012, 10:19 PM - Forum: Bosch, Actia, Autocom Discussions. - Replies (4)

`Hello. I have a question for u...

I have a bosch KTS 650.it is oldand slow. motherbord only accept 256mb ram if i ubdate that is No

So my question is: can i run esi tronic from my laptop and connect itwith the KTS to make it work on a car?

Print this item

  OCflash Downgrade OPCOM firmware if was upgraded from 2011 2012 official software
Posted by: manocao - 11-20-2012, 09:30 PM - Forum: Automotive Software. - Replies (8)

i found a program that is supposed to be able to downgrade opcom firmware to 1.39 EVEN if it was upgraded to 1.41 or 1.43 or 1.44 or 1.45 by means of 2011 2012 official opcom software

no matter if you started some 2011 2012 official opcom version with interface plugged in computer, which would have upgraded to 1.43 or 1.44 but disabling bootloader

2011 and 2012 official software versions of opcom dont erase pic of interface but disable bootloader

ocflash doesnt work if you started some 2010 version with interface plugged in computer, which erased your interface's pic

OCflash

howto:

1. connect opcom interface through usb only
2. run ocflash
3. click on "request interface" to check actual version programmed on interface
4. if programmed version is 1.44 or 1.45 click "load firmware" and select fw139.hex from "Firmwarefiles" folder
5. click "change"
6. select "automatic mode" and click "flash"

Print this item

  VW Polo immo off help please
Posted by: ghostrider - 11-20-2012, 08:27 PM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (1)

Good day members of MHH

Can any member help me with immo off in this ecu? Many thanks in advance.

ECU NO 036 906 034 FJ
4MV

POLO 1.4 16 V ECU IMMO MARILIE 03 MODLE 95080 login 02647


Attached Files
.zip

POLO 1.4 16 V ECU IMMO MARILIE 03 MODLE 95080 login 02647.zip

102
568 bytes
Print this item

BMW E46 320D has a interruption between 2000-2500rpm
Posted by: herman99 - 11-20-2012, 08:11 PM - Forum: BMW Group BMW, Mini Discussions. - Replies (9)

Hello everyone.I have now in my shop a BMW 320d E46 from 2004,euro4.The car has an interruption between 2000-2500 rpm.On my mega macs 55 I get a error on the mass air flow sensor (error code 16368).I've replaced the mass air flow sensor,I've cleaned the EGR but i have the same interruption.sometimes the car works well but most of the times I get the interruption.I don't have any power loss,the car has a lot of power. Have any suggestions?

Print this item

Mercedes Benz Circuit 30 or circuit 31 is faulty
Posted by: jay007 - 11-20-2012, 07:12 PM - Forum: Installation Guides, Procedures & Tutorials. - Replies (9)

I keep getting this error. The volatage supply at the diagnostics socket )circuit 30 and or 31 is faulty.

I Was getting this error on 07.11 but I done clean install of 03.12 and still the same. I have also tested the laptop with another mux and cables but still the same error.
I tested the serial port with a loopback connector and it passed.

I applied the Cal872 fix. only thing I have a D4 mux (china) and only thing I see in there is D2, Is this correct?

I am installing on a different laptop now just to eliminate the serial port. Anyone have any tips in the meantime..

Print this item

Fiat Fiat Ulysee 2,0l petrol IAW8p.22
Posted by: Repres - 11-20-2012, 05:55 PM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (7)

Hi all,
I have problem with fiat Ulysee 2,0l petrol.
Cables from kaypad are damaged. Customer change battery and from this time wan´t start this. I mean when I read Motorola in keypad I find code. In Motorola is easy find code, but inside this keypad is NEC.
In ecu is Motorola 11A1 C11W and 27c512. Is possible make correctly disable immo? Or, when I make virgin ecu in MCU and connect other keypad but with motorola with known code can I use this config and correctly start?
Many thanks
And sorry for my english.
BR
Matias

Print this item

  EZS faulty, new one?
Posted by: jacek123 - 11-20-2012, 04:57 PM - Forum: Daimler Group Mercedes-Benz, Smart Discussions. - Replies (1)

Hi,
if a ezs of for example W210, W202 or W208 is faulty, is it enough just to remove the one or even two cpus and put them in an other EZS ?

best regards

Print this item

Sazki HELP ME, I need SUZUKI pinCODE
Posted by: forumoto - 11-20-2012, 04:21 PM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (2)

Please i need the pin for Suzuki XL, the vin is VIn= 2S3DB417476116383

the scanner display three codes but all did not entered... and this are the three generals kinds being tried...

0408,0804,4229


the car is 2007


thanks in advance
PLEASE SOMEONE HELP ME, I NEED THIS CAR START..

THANKS

Print this item

Mercedes Benz w211 key
Posted by: IvanADE - 11-20-2012, 04:47 AM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (5)

Hi,
I have a question about w211 key:
Is it possible to copy Nec from one key and programm it to the another one, that both of them would work? or would there be some conflict between this keys after using?

Print this item

  ecu opel corsa
Posted by: auto421 - 11-20-2012, 04:44 AM - Forum: Automotive Airbag, Dash, ECU, IMMO. - Replies (4)

hello, someone explains to me how to read this ecu on the bench with fgtech Galleto 2 ¨? and what color wire kline in fgtech Galleto or follow the colors that are in the photo? grateful to help me and I'm learning. tankyou best regards

Print this item

  Xentry 3-2012
Posted by: autobengal1999 - 11-20-2012, 02:52 AM - Forum: Automotive Software. - Replies (6)

Hey mates!
Before anyone attacks me for not searching and reading posts, I have pages and pages.
However, I have "two" multiplexers. One is original and 3-2012 works perfectly. But I also have a Star C4 clone and when I try to connect to it I get Das Fixes (1.17)-7.872 Error. I assume blocked MUX. I applied the 872 Fix and rebooted and still no connection. Same laptop. Can anyone give a helping suggestion?
Thanks guys.

Print this item

  vw bcb engine p0171(16555)
Posted by: Benny_d - 11-20-2012, 02:37 AM - Forum: VAG Group VW , Audi, Seat, Skoda, Bentley Discussions. - Replies (4)

hello people.
have a problem with a vw golf 2003 BCB engine code.
fault p0171(16555) system too lean.
smoke tested for inlet leaks-ok
map sensor reads 30hpa-20inmg-ok
front lambda sensor bank 1 sensor 1 has been replaced.

in live data using kts short term fuel trim reads -100%Angry

Any input will be appreaciated if you have any suggestions.
thanks in advance

Print this item

VW VW BCB workshop manual?
Posted by: Benny_d - 11-20-2012, 02:30 AM - Forum: Automotive Workshop Manuals. - No Replies

hello people,
does anyone have workshop manual for BCB engine?
please share if anyone has available
thanks in advance.

Print this item

Audi b6 a4 skc help "found"
Posted by: dylan - 11-20-2012, 02:15 AM - Forum: Automotive Airbag, Dash, ECU, IMMO. - No Replies

Edit: Found the skc, thanks.


I am trying to retrieve the skc from my dash dumps. I have a few dumps but I'm not sure which one is right. can someone please help?


Attached Files
.zip

bosch 2nd.bin.zip

36
1.24 KB
.zip

bosch RBx.bin.zip

32
1.13 KB
.zip

_Audi_B6LMJ02 V006.05.bin.zip

34
1.28 KB
Print this item

  EGR off Cady edc16
Posted by: zelda - 11-19-2012, 10:36 PM - Forum: Automotive Tuning. - Replies (2)

Hi
someone please can help me turn off EGR on Cady edc16
dump attached with bdm
thank in advance
Best Regard


Attached Files
.rar

flash edc16 cady.rar

87
545.24 KB
Print this item

Mercedes Benz Xentry Simulation
Posted by: jay007 - 11-19-2012, 10:22 PM - Forum: Installation Guides, Procedures & Tutorials. - Replies (4)

What is the purpose of Xentry Simulation? Is it just used to test the Installation without Mux Connected?

Print this item

  solution for texa
Posted by: reda75 - 11-19-2012, 09:02 PM - Forum: Software Requests. - Replies (1)

Hi,

Please any solution to update my diag TEXA navigator ?

Print this item