Im looking for an immo off file, for a Nissan Micra K11 1996..........
I know that exist a 93c46 inside...but I dont know where.......ECU# 0261-203-980
is there a bin file available for immo off and a photo from inside so i can start this car?
Thank you!!!
HELLO!
PLEASE HELP!
I NEED TO DAMP IMMO OFF TOTAL FOR PASAT 1995 TDI ECU BOSCH 0 281 001 411/412 _ 028906021DD (MSA 12)ECU HAS 27C512 x 2 and 93C46
Thanks in advance !
Hello I need some help my glow plug module shorted and cant start the van now start error displayed. Can someone please post a picture of the eeprom location? and immo off dump? thank you
2005 sprinter
A 647 153 28 79 OM647 2.7L
also does anyone have an immobilizer virgin dump?
and will i be able to code them with DAS thanks again
i hope i could get some help for my issue/problem.
I start the projekt "build standheater from webasto in to my w204". i have finish it this week succesfully. But now the problems.
i have Das /Xentry 09/2012 running on my system very well and can connect the heater over can-b with the mux.
Thats the way with xentry , but DAS do not listen the heater, so i cant connect.
so my chance is only with xentry.
I want change some points, like Co2 settings. I need the password.
Year / Date : 2012 Version : 1.63 Developer : Ford USA Web Developer : www.motorcraftservice.com Language : English Tabletka : Not required Description : Language English ! The disc contains guidance on repair and maintenance of cars Ford from 2006 to 2013th model years. As there are electrical. Staged repair of units and descriptions anregatov. Adjusting data and reference material. Extras. Information : Distribution includes 6 images DVD (2006-2007, 2008, 2009-2010, 2011, 2012, 2013). To install the program with the correct model year to the corresponding disk image to burn to DVD or USB flash drive. You can create a virtual disk. So do as you prefer. Before installing change the date on the computer on July 15, 2012. Click on the icon for DVD-ROM, a window startup. Authorize the installation. After installation on the desktop icon "Sevice Information". Run the program and use. If you want to set all model years it was doing the above process for each DVD. I installed Win7 on it compatible with Win XP SP3. Basically three months to stop working due to set time code. Put the date July 15, 2012 and use further. The idea is not to work at the current time. But on my Win7 works. For normal operation requires Adobe Acrobat 5.0 or higher.
I am working on a BMW X6 2008 model 6 cylinder petrol engine, I got this error code on the DME -
P16C6 - 2E7C - bit-serial data interface (BSD), signal.
Going through the diagnosis procedure, I got a term referred to as 'QLT'.
The repair procedure is as thus:
1. Disconnect all BSD_components (alternator, battery sensor, water pump) except for the oil sensor. Clear fault memory. Ignition off/on. If fault code is stored again: QLT is defective and must be replaced. Repeat test.
Ford ETIS Europe technical information system presented workshop manuals, service manuls, repair manuals Ford, maintenance, diagnostic trobule codes, technical service bulletins for all models cars and trucks Ford, European market.
The Technical Information System (eTIS) provides Technical Service Information via CD-ROM. It is updated on a regular basis and gives access to the most up-to-date automotive service information. It includes publications such as Workshop Manuals, Technical Service Bulletins, Service and PDI Checksheets.
Compatibility:
Operating System:
Windows XP 32bit
Windows Vista 32bit (x86), Windows Vista 64bit (x64)
Windows 7 32bit (x86), Windows 7 64bit (x64)
Browser: Internet Explorer IE6, IE7, IE8.
Activation: Stop the FordEtis Service. Unzip Ford_Etis_02_2010.zip Onto installed path (eg "C: \ Program Files \ FordETIS \") or edit your config.ini Related to Installation path.
i want autocom relase 2012 2 and whwn i down loded it it was over 3,5gb in size when autocom 2011 was 1,6gb. Is i two programs or what? or is the update much bigger now. If i only wnat autocom 2012 2 where shoud i download it. And i whant nordic languge. what is delphi
Hi ,
I got a new autocom cdp + checked it and it does not work.I get no vci found.
I see the ftdi chip has default VID and PID as a simple USB to com converter.This is not a firmware autocom.I tried ept from the old device but it does not work.Does anyone have success with the new CDP + clone with s / n 100251 and which driver need for work.
Sample 232R UART drivers or drivers from autocom folder .
Hello! Does anyone knows how to change a BMW's language (inside the car) with BMW ICOM? I think i almost managed it but is asks for a code...what code is it? Where can i get that code?
Hello,
have anybody experience with the sxp autoboss pc max? How is the software? Where can i get the Software? What is the last availebel release? Quality difference by the vci? Work it over Bluetooth or wifi?