CAT Caterpillar ET Diagnostic Adapter works with Software Perkins EST and New Holland EST?

if someone need lpg software or help here i m....
here is some link http://lpgkit.eu/interface-software

Hello.

I need dump for 1H0 919 860C, SW 5.1, EEPROM 93S56 (propably 93C56 also ok).

Thanks in advance.

hi
i hav sprienter 1999 with ecu MB 027 545 50 32
BOSCH 0 281 001 982
immo in ic 24C04
IMMO BOX Temic MB 020 545 58 32
MCU 0D62J

problem:the dump in MCU 0D62J is deleted,for soulition i put another dump (24C04 and 0D62J) from another sprienter and i creat a key with zeed-bul but no work.
wat is the problem?
thenks

Hello, does anyone have new drivers for ecm titanium 1.61? I need it especially for VW Caddy 1.6 TDI 75hp 2011?

Ford Service Information DVD (2006 - 2013)

Quote:Including Factory Workshop Manuals, Technical Service Bulletin's, Wiring Diagrams & Powertrain/Emissions Diagnostics Information.
This DVD covers Ford, Lincoln and Mercury Vehicles

I've been searching for something like this for years, little dabbles here and there till I found this great DVD. This is the most complete resource that we'll ever find for FORD products.

Mount the ISO to install this DVD or you can burn with your favorite burning program and install from DVD. I have this program installed on my Windows 7 computer and it runs perfectly. All pages are printable by clicking the small icon at the bottom left side of each page.

Attached Files

Ford.Service.Information.DVD.2006-2013.zip

1025

1.86 KB

Download

To enable cruise control on my Peugeot 206 1.6 16v NFU 2001, I need to wire an extra brake switch to the ecu.

Does anyone have the pinout of the ME7.4.4 ecu?

Hello

I search software for vas 5054a to bentley and lamborghini in english
Please help me
i find software vas lamborghini and he not fonction there are adaptations fonctions only...and he not work

need code for vw
blaupunkt 7 612 002 044
vwz1z2h8077143
1k0 035 191d

hello everyone, I have a problem if someone can help me thank imenso.estava to schedule an ecu edc15c5 a smart diesel when the power failed, I returned to restore power but no longer can program the ECU when I read not of any reading data, already tried with various programmers. can someone help me with some solution, already thought amd take 29f400BT and read with william programer, upa programer but do not know which pins to programming, or will there be another solution. please help me. tank you
best regards

DAS & XENTRY 201209 installation was successful.APP253 201207 version was first installed.And later version upgrade. 201,209DAS did not run, the problem I think, and then upgrade the MUX passed without problems.Mux need to upgrade your DAS is running without any problems.Version is as follows: After upgrading my MUX.One important thing DO NOT lic_key_2 as read-only.

OS: 2.0.20100825
CSD: 2.00.20110502

Hi all, is there anyway to get hold of software update files for citroen to be flashed in with lexia?

Hello all,
who have please full backup (eeprom+micronas 3217G) from dash 1Z0920842C petrol RS from xprog withou immodefect?
Many thanks
Matias

Hi guys,
did someone has also a AK500? Well, i have allready read out some EIS data and keys, but i have now a problem with a old Motorola Key from a W208. Do i have first to renew it ? Because for renewing it is neccessary to have NEC cpu, and this is in the newer keys ?!
Or is it not neccessary to renew those old keys and only put new key data on them?

And second question.
If i have the .bin from the EIS and i will give them to the webmaster here to create key files, how do i get them on the keys with the ak500? Is it possible or do i have to get a other programmer, because i think that for the ak500 i need also ecu and esl data?


thanks and regards,
jacek

"Can not upload file - Too large for php post_max_size directive. Please press the back button."

I have this message while trying to upload attachment (3kb) in this topic http://mhhauto.com/Thread-Autocom-2012-2...3#pid96373 while in this topic it's no problem. I'm using only 50.01 KB of 15.14 MB. Please help.

Hi, anybody help me with this file from berlingo ECU autoliv 9673393680 - 619 90 78 00. I need clear crash data stored in S25A32. Thanks

Attached Files

95080-S25A32 crasch berlingo.rar

88

517 bytes

Download

I recently posted a question about a lost key for a Vito 109. I ended up ordering from a local merc dealer. I was talking to him today and asked him did he do it himself or send it away. He said he got the key from Germany. He mainly deals with sprinter vans and I was asking him what he does when people lose keys etc etc and his response was he gets them all from germany. I was reading here about turning the Immo off and if i am right then any key that fits will work. Am I right in thinking that? He said that he would love someone local to do it but the one guy he had was very unreliable. This got me thinking and I told him I was very interested in this kind of stuff and would look into it if he could get me some work out of it. I work in electronics and computer repair and have no problem lifting chips from boards etc etc. I own a willem programmer and use it for reading and writing bios chips in laptops. This willem programmer does everything I need it to do but I realise I will need better equipment if I want to go down this road. Was reading about the a ak500 pro but if I have no problem lifting chips etc would I need to fork out for it. Starting off i just want to be able turn off Immo and use any key to start vans that he has no key for (he said he has a few I can practice on). Will the willem programmer I have be any good or will I need to invest. I dont mind spending if I have to but only if I have to. Can you give some advice of equipment I need and where is best place to buy.

Has anyone the Smart Tan calc from JC for sale? I'm looking for the new 2012 version!

Thanks!

Hi All,

I have been struggling with this one for a few days. I have managed to program keys using my CarProg in the past, but there seems to be no direct support for this ECU.

The story goes, the car was imported from Japan and when it arrived at the docks on our side some **** stole the ECU by cutting through the whole harness. I have so far managed to source replacement plugs and ECU (both used). Everything has been wired up nicely.

Anyways, I tried (with no luck) to add the keys using the 4Runner setting on the CarProg but no luck and 'that light' is still flashing. The 93C56 EEPROM was de-soldered from the ECU to be read with no errors. For your information the exact vehicle model number is GF-VZJ95W-GKPGK. The ECU part number is 89666-60630, the Denso part number is 275000-0803.

I am attaching the original dump HERE! (ie. before I did anything).

I would like to add 2 'Master' keys, here are the codes:
- 6E F8 F5 05 00 00 00 00
- 3D 5A 2A 06 00 00 00 00

Any help would be highly appreciated, thank to all who have the time to help!

how do i include a picture with my post ,
done search for it but did not find out how,


thanks

Hi!
Why I do not see the item development data in the multimedia section in das xentry 1.2012-3.2012? I need to coding a ntg 2.5.
in older versions it was possible ....
thanks to those who help me.

Hi mhh members,
im beginner in dump and i need help to make EGR Off on this dump
car :audi A4 / B6 / 1.9 TDI 96 KW /130PS


thanks for your help

Attached Files

Audi A4 original.zip

55

216.53 KB

Download

Good day members of MHH

I have a Nissan Micra 2006 model, 12k chassis and 1.4lt petrol in my shop with engine code CR14. The vehicle came from another workshop with not being able to start. The previous workshop came up with camshaft sensor fault codes. They replaced the sensors but still did not start so sent it to us.

What we found was that the timing chain is stretched so badly that camshaft sensor is picking up at the wrong position on the camshaft and causing it not to start. We have removed the engine to replace the timing chain and timing chain gears but I am wanting to find a workshop manual on this engine to do it right first time around as taking the engine out again due to incorrect fitment is not an option.

So I am asking for help from member here who might have a manual for me or a link of where to download a manual.

Many thanks in advance

Please, anybody has some information about Weiro machines, anything - schemes, manuals.

Hello Members,
Is there someone in here please who can provide the Radio Code for my 1996 E34 i want to sell tomorrow? Picked out my Becker and want to install the original one but cannot find the damn card...
I tried 5555 and 1555 but they do not work.

I have those stickers on top:
BMW Reverse RDS (Blaupunkt)
6512-8352861
BP4836T4617827

The green on the side:
7644836340
T4617827

Hi all. Dampik cleaned from the crash, there was one error 00003 Control Mdule.
This error can be removed only by the replacement of the module? Or didn't remove up to the end information on blow?Sorry for my english))))
module 8E0959655G

Attached Files

Audi A4 2007г.zip

43

2.94 KB

Download

Before activating new version of AutoCom or Delphi use these files.

Attached Files

CDP_Cars_Certificate.rar

1987

61.33 KB

Download

CDP_Trucks_Certificate.rar

1032

61.24 KB

Download

CDP+_Cars_Certificate.rar

1588

61.34 KB

Download

CDP+_Trucks_Certificate.rar

1031

61.25 KB

Download

DS150E_Cars_Certificate.rar

1155

60.42 KB

Download

DS150E_Trucks_Certificate.rar

823

60.45 KB

Download

Greetings to all the Auto Guru's

Serial Number: VWZ2Z2V7305119

VIN#: WVWZZZ3B2WP262087

Thank you.

bought an a3 have a few probs and the milage reads 9999999,
mag menelli dash i believe,
any tools out there can can sort this !!!!

Hi

anybody help me to get Delphi (EJBR04301D) injector test data.

thanks in advance

Neelakandan.K