Hi trying to find a supplier who sells the Iveco Eltrac interface and Easy software cheap, seen some for sale but costing a few thousand pounds, does anyone know if there are china versions, if so where can I purchase, thanks.
Hi i bought a hq autocom from e-bay, it came with 2011 release 1, tried it out and it communicated with all ecu's on my 07 plate citroen C1. I then updated to 2011 release 3, followed by update 5. all went well, firmware flashed fine etc. I now find that it will communicate with all my ECU's on my C1 except for my airbag ecu. My mate has one with 2011 release 1 and his communicates fine with my airbag ecu. I then reverted back to 2011 release 1 and found my interface again communicated with all my C1 Ecu's in cluding airbag. Upgraded again to 2011 release 3, flashed firmware and again found would not communicate with my C1 airbag ecu. Anyone else found this problem, certain ECU's fail to communicate with 2011 release 3 but are o.k with 2011 release 1?
I have had a clone Launch Diagun , serial number 980541216700 and for the past 6 month and it works well and have had no problems with it. The software on it was not old but at the same time was also not the newest software version. For example the VW/AUDI version I had on it was 25.93 and BMW was 44.40.
A week ago my supplier gave me the update software and I installed it and it works perfect. For example Audi is now 26.20 and BMW is 45.30 so it is an update on the software I had on my unit.
When my supplier gave me the update he said I should delete the old GAG file and copy the GAG file from the new update onto my SD card which I have done and it works.
But what is worrying to me is that my older software GAG file was 603mb containing 6436 files and 232 folders but the new update GAG file which he gave me is only 395mb containing 2748 files and 234 folders.
Meaning that the new GAG file is almost 50% smaller with less files and folders. Can any member maybe explain this all to me.
Hi mhhauto members~
I was exhausted.
my system is win xp sp3 original ver.
EWA(08/2012) installation error message appears.
I install a lot, but it did not solve the problem.
Look at the attached picture.
Always receive a message from the steps of the 14th.
Please someone help me
hi all friends
i have this error in xentry sim, after 3 or 4 times with this msg i click ok, then all is ok.i want just to know the orogine of this error.
thank you
The application which is an advanced calculator for correction, programming and repair of electronic meters car drivers. NEO6 is a fully professional mobile application that offers maximum flexibility and comfort, while maintaining ease of use. Ever-growing base of algorithms implemented in the programmable logic controllers raises the amount of available programmers with guaranteed speed and safety.
A huge number of satisfied customers in Europe clearly indicates that NEO6 is the best of the available calculators to program car counters, tractors, combines and construction equipment in the world.
NEO6 possibilities:
programming and change the course of the electronic counters.
- programming and change the course of tractors and tractors
- programming and change the course of agricultural machines and combines
- programming and change the course of forklifts
- programming and change course in construction
- repair of electronic meters (if you have bad data in the numerator)
- repair and programming modules AIRBAG
- programming lamp modules (switch to LED's)
- PIN code reading car drivers (CIM, engine, BSI, UCH, etc.)
- read, program and change the code on the radio.
Please submit orders PM
Skype: autoexev
Quality of the program depends on you, and the number of licenses purchased.
Best regards.
Hi
Could you help me on this,had reset this unit with Carprog,AVDI,...and allways the same errors ( unit and the two side sensors faults).
Need to change the unit or is possible to repair it?
Send dump.
i lost my key remote and the car it doesnt start ,i know how can i solve the problem i must to remove the ifz immobiliser behind the instrument cluster and read the od53j and generate from od53j new transponder and new remote dump , but wich software or wich machine can do it ?
i just received my china clone autocom cdp but cant setup.
so far i switch av off
start setup on cd
use keygen for activation.
program loads then crashes
delete files for windows 7
reopen program but starts activation all again.
hello
i have had my genuine ford VCM for a very long time, updating the software between JLR and Ford often and many times, until today, clearly i had used the vcm on a jaguar the last time i used it. i updated my ford software to V75 to-day and on connecting the vcm, it asked for an software upgrade which i granted, half way through the vcm locked out saying it needed a new activation code. can anyone help with my dilemma.
regards
jensen1
Hi
Is there anyone who is willing to help me with
getting my Xentry 5/2012 to work?
Have bought from China but have not managed to get it
to work.
Have TimeWiever of contact.
Regards
PKSH.
Iveco Easy links on rapidshare.
Pass ONLY via PM.
Do not ask in thread !
Activation code for software can be generated too.
Enable PM on your profile first.
I can't sent PM back !!!
hi guys i find the problem when i want to add cd seat and skoda for vas pc 5054A v19 french.
gives this message in the picture
please i need the help
thanks in advance
Hi folks, my volvo vida works fine for couple months, now when i want to start explorer says that he can't find website, also icon VIDA shows status starting not running and i think that is a problem. I tried to reinstall but nothing has changed. Does anyone knows how to change it?
This are Excel spreadsheets with the original tools you'll need to work on your CAT engines (Truck engines only). The lists are clasified for procedure (Dissassembly & assembly, Testing & Adjusting, etc.), by engine system (fuel, governor, cooling, etc.) and for Troubleshooting.
If someone needs this lists for any Caterplillar marine, industrial or genset, send me a PM.
If this was useful to you, please, don't forget push "THANKS"
i have mercedes e 210 1998 i lost the key remote and the car it doesnt start the red and green light flash on and off , i removed the IFZ immo behind the instrument and i need to generate new dump for new remote so wich machine or wich software can do it ? can read the od53j dump from immobiliser and generate new file for remote control fitted the car .
Hi ppl, can some1 help me with this. It is about sprinter 311 CDI, 2.2 ,
2002 Y , 80 kw , 611981. I have problem with automatic transmission,
I dont have 4 and 5 gear and can not be put in A
And this errors I get:
AUTOMATIC TRANSMISSION
P2012(this error can not be deleted)
p2034
ENGINE
P1481
P0703(this error can not be deleted)
P2203
P0500
And if some1 have workshop manual for this car, especially for automatic transmission, I would be very grateful.
I'm new to the forum and to the whole car software thing so it would be great if somebody could give me advice on how to connect Actia to the car.
I downloaded Actia 3.2011 from here and used an obd2 to usb cable to connect it to the car. When I rad the software it couldn't connect because the VCI was not found.
Could you please instruct me on what exactly I need and what steps to take in order to successfully diagnose the car?