I have also one problem:
If I click on the "WIS net" Button it modifis me any network settings an try's to go online to the online EPC net.
How can I prevent Xentry to modify my network settings and/or how can I tell Xentry to use the localhost:EPCnet or / do nothing if I press the EPC net Button?
The WIS Net is installed via SDSwitch as standalone. After that I Installed the EPCnet and the EPC-DB's with the "EPC net" admin tool up to 09/2012.
Can anyone help me, on this issue?
So I have been racking my brain and spending days and days of trying to figure things out. I have been having all kinds of different problems no matter what I did, how perfect I followed direction. Then I finally read you should not use prolific usb converters. Well I finally bought another FTDI converter and guess what?! It worked with my current DAS install with NO problems. I was always getting different faults and also Data are being determined .................................................................... So if you are using one of these (non FTDI chipsets) trash it.
Here is the one I got, I cannot recommend it 100% because I dont know how good it is, but it does work.
Actually I got one Sdconnect from http://stcardiag.com
The Mux came with many troubles:
1: When U place batteries inside, the voltage of the car will drop down (-1 to -1.5 from the real value of car battery voltage) thus troubles in programming ECU's
2: Not Stable. Most of times, U have to remove and install wireless card to get it working!!!
And Finally Its damaged
Just today, I got bad smell from inside. I opened it and located where is the damaged part inside as shown in the Pics.
Now my questions:
1: could anyone supply to me this Chip Number:
Samsung K6R4008C1D-U10
2: From ur experience, where is the best quality to buy?
Sorry for my bad English and my dyslexia help there too not participate!
But hope you can understand and help me with some problems with my diagnosis software for my BMW / Mini .... I use it for the following hardware:
IBM Laptop and port replicator to comport to use (t41 with 2 hard disks)
Obd com interface (http://www.ebay.co.uk/itm/BMW-INPA-EdiaB...087281%26)
features:
Connects to RS232 com port
Double K-Line support by two Motorola MC33199 K-Line drivers
and logic gates
Battery voltage detection by RS232 control line
Ignition voltage detection by RS232 control line
Switchable K-Line pull-ups by RS232 control line
I fully running diagnostics (GT1 DIS V57) and everything can read and operate without problems but.
But this money is unfortunately not for Progman SSS V32
The program I can use for the following things and manage to my mini:
Car Key Memory (CKM)
Encoding is also only for the KOMBI1
But not of the other things like the KOMBI2 / DME etc.
Well I could see the BC (onboard computer) encode without saying that the voltage was too low.
I've been here a while doing ...
Everything goes well when loading the program and gives progman 14Volt on terminal 15 and 30
But once he has loaded all vehicle options and the chassis number has recognized the voltage goes back to 12.70 I use to guarantee a constant battery charger for the security industry but can not get out ....
I also have the 5 different changes.ISO files (to hard-code the voltage error) attached to me Vmware but unfortunately made no difference I've tried all 5 1 by 1 but without any result.
and easily activate all options as follow me home, auto lock, etc.
I use all required software on a clean windows xp hard drive without firewall and virus scanner with Vmware 6.0 INPA and ediabas and open the diagheadserver and IFH service.
Progman works or only the coding not ... and I want my new rev coding but unfortunately without success ...
Even if in the administration section of the interface test so that is all without any problem .....
Hi guys.
I'm trying to read a file from a Mini Cooper S with a clone MPPS and I got some problem.
When I've tried to check ECU ID I got an error : No external voltage found.
I've put a good power source to feed the battery and my laptop is plugged to the wall.
Could anyone supply a code for a radio in my smart car? It has Grundig unit and codes are:
MC944341232778
CD mrr 0009443 V003 C59Z 00
9.18436-8152 G.HO 05-00
I could have used websites with auto calculators, but I like this site and as a thank you gesture I will donate 10 euro to this site after I will get a good code.
Hi guys i want install , DIS GT1 on my Dell latitude D610 , i tried with easycd base v44 from but it failed with configuration of network card because the network card is not in the list , anyone did he install it or update a driver on scopen hardware ??? thanks in advance ,
best regards
Hi guys, i'm a newbie of this forum.
I've got a Fiat 16 Mjet 8V (120CV)
the ecu is a Bosch EDC16C39 CF4/EOBD diesel injection (1.9).
I've got a lot of problem with DPF...
I think to take out it and reprogram ECU.
there are some italian forums in which guys modify your ECU file taking out DPF for a little money, but they need the .ori file.
Basicly I'd like to know which SW and HW is needed to read the ECU and then write it again.
I've got this:
ELM 327 cable (I use it with FES)
EOBD cable with galletto 1260 SW (a thing like this: http://www.ebay.it/itm/KIT-GALLETTO-1260...5020wt_118)
the sw given with galletto was very confused and poor, but the HW is good for reading/writing?
Gentlemen, I need some help from experts, please. I have tried to install XENTRY-DAS 9.2012 over working 7.2012. After first step which upgraded my version (see picture) I cannot open My Computer, nor Control Panel. Error message as on attached picture : The action contravenes Star Diagnosis security guidelines and cannot be executed. The Xentry is not fully installed because I have no access to Xentry/Frame folder. I’ve successfully installed previous versions 1.2012, 3.2012, 5.2012, 7.2012 and this happened to me for a first time. Can anyone here advise me how to overcome this error? Many thanks.
Hello everyone, has anyone had problems with 2012.2 Audi A4 2.5TDI diagnostics year 2003 with 2011.3 automatic transmission works perfectly, but it does 2012.2 The automatic transmission does not go with 2012.2
was the first car I've tried, after installing version 2012.2, golf 4 you works perfectly in time I encountered the problem only on automatic transmission A4 03 years, someone else had problems on other cars ??
Need help to repair my KTS550. Its broken in the diagnostic work. Now when i conect him to external power suplly green LED blink 3 times and pause and again. On USB port Windows see Human device interface (something like that), i try with RS232 port but no luck, software do not see hardware. USB port is OK and how much i know to check, PDIUSBD12 is also OK. On board have 2 8pins IC-s (LM2672MADJ + LP2951ACMM) where one give me +5V and anotherone give me +3,2xV. One smd fuse is OK. I do not know where to look for further. Any advice what to check or someone know exactly the problem ?
FDOK calculator
FDOK has two calculation types:
XT is used for changing of NOx Torque limit
XN is used to erase emissions-relevant fault codes in actuations of SCR
Hello all,
I would be very grateful for any input. I am currently repairing a friends crypton CMT1000 tuning machine, which has a failed hard disc. I am desperate for a copy of the operating/interface software for this machine, as he cannot find the original install discs. Again, I would be very grateful for any help.
I installed DAS/Xentry (AppID 252) up to 09/2012 without any errors. The mux is working fine.
So, after that I installed WIS and EPS also up to 09/2012, also with no errors.
I can start the WIS and EPC over the EWA net with the Internet Explorer.
But if I would start WIS over Xentry, Xentry tells me "Wrong value at system.ewanet.standalonepath. Please check the GlobalSystemSettings.properties".
Ok, I look into the file and the EWA section shows me this:
So, on my hdd is no folder named wisnet with a standalone.bat. I searched the complete hdd. There also no standalone.bat!!!
I think the wisnet app is not installed correctly?!?!?!
How can I fix the problem?
Can anybody help me?
hi, can anyone suply a good manual to install this version, i have a fresh windows already with partitions.
i get to newguide2i from your friend zoolokas.
Firstly, I'd like to thank you guys for sharing!
ok here goes my list of questions
1. once I replaced the od5.exe, i attempted to add data paths, however, the program doesn't see a physical disk nor the directories that I've placed my repair disks on, am I doing something wrong here?
2. I have 1st quarter 2009 data, is that why its not reading? should I be using v5.8.1.9? I read something about the new version being able to use the old data set. Am I wrong?
3. I was also wondering if I didn't place the files in the correct directory name or location under main drive or under "c:\mitchell1"