Hello, I have a problem with Peugeot ecu MD1CS003 that car do SCR OFF, car run fine a few days but after 2 - 3 days the car not run fine and appear P1632 - error internal ecu. I write original file and same problem now. The ecu hardware is perfect, not have problem, I read in other forums these problem and they solve it, but dont know how solve it.
hi sorry i again upload this situation file Mercedes med17.7.3.1 pop bangs SWITCHABLE car is 400 petrol not amg i ready to pay after all is ok and test...
I've got an old Brainbee ST-6000 without any cables, don't know if it works. The multiplexer box is there. Does someone know the pinout from the db15 connector (ecu) on the multiplexer (ground and V+)? Or someone can meassure the cable pinout from obd16 connector to db15 connector?
There ist an rs232 connector, too. Does someone know what cable is needed for PC connection?
The vehicle is a 2009 model Passat CC. WVWZZZ3CZ9E533844 Engine code CBBB The old gearbox is LQT code and has AJ coded mechatronics on it.
The new gearbox is coded KQC and has AJ mechatronics on it.
I'm having problems with these two mechatronics. I have a solid AL mechatronic. 2014 model. What code should I put in this mechatronics?
The code that appears when LQT is observed is 02e300051t The code appearing in the KQC view is 2e300051 When using a different software, I get the p2711 error after the basic setting and 3rd gear. P2732 malfunctions when used with another software. It gives a different error in each software. The vehicle could not adjust the gear ratios. Is there an Al sgo or bin file that is compatible with the KQC gearbox and compatible with the CBB engine?
Can some body remind me why we cant write this modules? I read one with hpt, it said incorrect checksum, i played with bin and converted back to hpt, all checksums fine, hpt opens the file i can see all calibrations. Where is the issue can some body tell me? they r locked against write?
Hello
I need to check the checksum. After the modification, the car does not want to start.
Please correct me because I don't know what I'm doing wrong
Hello,
I tried do mileage of bmw X1 2020 with DP5 , Prepare EEP is OK , Flash OK too, but impossible to restore EEP.
Need help to restore EEP.
Attached file , backup DP5 and read with programmer.
thanks
I was working on 2004 Mini Cooper all keys lost, I made two keys and no crank no start,
I short 1 and 2 pins on ews connector and there is crank.
on live data keys showing good but I get "starter motor blocked due to p/n"
dme EMS2K
What can be the issue?
There is a chance that ews is bad or eeprom bad?
Better to immo off?
any one knows how to clear crash airbag code clean Im try to read the mcu but im not able to do it because in the board is there 2 holes and the soldering wont get stick
and the epprom is different or any one knows which tool I can used to fix this problem or which adapter I got im608 2 with xp400 or how to read the mcu cr16 chip with xp400
Hello,
Looks like both of my rear seat controllers show fault when scanning, after testing both back seats I can confirm that function like a lumbar support and sides inflation both don’t work. Coincidence that both have failed? Scanned with xentry
Error code B1E7900. The air pressure sensor has a malfunction.
N32/20 Left and N32/21 right. Hardware 222 901 27 04
Can’t find anything online. Has anyone successfully repaired one of these? Is it something possible to do or is buying a new one the only outcome?
2012 BMW X3 keep blowing fuse 1 in power distribution box
some times its good for week some time blowen i 2 days
vin:L736049
after changing fuse and deleteing errors 2 coming back in a few min
102A01,101F01 tomorrow i will drive it a bit and than see what errors coming then.
![[Image: Post-Instagram.jpg]](https://i.ibb.co/yzhJvCX/Post-Instagram.jpg)
![[Image: QJ-SRT-800-delphi-mt05-xdf.jpg]](https://i.ibb.co/fzN603mL/QJ-SRT-800-delphi-mt05-xdf.jpg)
