Hello can someone help me to do a Stage1 + DPF + EGR off?
i have a Stage1 with DPF and EGR off, but the bus goes into emergency at full throttle and 1500 rpm (P0087) with ORI everything is fine and without DTC
Hello!
I am looking for a 100% tested solution for this Navara 2.3d 2017 Sid309 ecu, DPF EGR and STAGE1. I tried many auto solutions but all failed, with some I had limp mode with no errors, some did not even switch off the dpf light and regen.
Please only tested solution, I cannot afford to write a bad file again.
PS: I am looking for quality work, not free work. Thanks
I attached the standard obd read by FLEX. If needed, I think I can also do a full read (bench or obd, not sure).
Hi i have a problem to tune stage 1 this car,ecu is edc17c69 euro 6d final. Can anyone help me please for the solution tested in this ecu? because i have tried two many solution stage 1 but the car in the full gas situation dont perform.
hey all, looking for some help with my 2014 chevy cruze diesel 2L luz with edc17cp47 ecu. im trying to figure out how to read the bin file. ive tried pcm flash on the bench wired up as in mod 71 pinout diagram and cant get it to read. does this ecu need to read with ktag? any help would be great thanks.
Hello, who can remotely transfer the seed key from the BCM to the PCM and a 2015 Jeep Cherokee for a reasonable price tomorrow? Needs to be done online. The PCM has been replaced with a new not used ECU. It has already been correctly flashed and programmed. I have the five digit PIN but no way to enter it. I would copy the EPROM from the original into the new one except for it is shorted out. Basically somebody needs to run the PCM replaced option under the BCM and that's it.
Hi problem with 2016 Vauxhall Mokka 1.6 diesel egr system
Got fault code P0401 egr insufficient flow detected ( renewed egr valve + egr cooler) which was blocked
Now after approx 20 miles eng fault light on code P040D 00 set egr position not learned
I have tried various diagnostic tools none of them has any programming or learing available for egr valve
Has any body got fix for this fault
Thanks Joe Clip
Im trying to save a ecu by switching out the internal ambient pressure sensor on this conti VD46.1 ecu.
Now im struggling to locate it on the pcb... There are some more chips under the upper deck but that seems like a bitch to get off without breaking anything.
Does anyone have experience with this ecu and maybe help me locate the chip? I have searched for pictures on how they look like but with no succes...
Hope someone can help me with this!
Thanks in advance!!
Hello mates, I’m working on a Dacia Duster 1.5 with an SID306 unit, reference S180095106A.
The original unit was showing two errors: • DTC062B16 • DTC062BF7
Both errors are internal faults.
I bought another unit with the same reference and removed the immobilizer using an emulator. However, the car does not start.
I cloned the unit, but the faults persist, so the issue seems to be in the software.
I’m considering extracting the ISK and VIN from the original ECU and writing them into the new unit. However, I haven’t been able to determine where the ISK is stored in this unit.
I retrieved the pincode from the car’s original UCH module using Renault ECU Tool: 9C BA 36 6A 04 A7
I am please asking for some help because I know almost nothing about Toyota cars, and my health bad so I cannot do the repair work myself.
Problem is with 2012 Prius.
Car one day behaving badly - engine badly misfiring/shaking (death rattle?) and low engine power. Coolant level was fine, could only see fault code P0401 (history, not current/pending) - Launch saying insufficient EGR flow.
I wanted workshop to just clean EGR and EGR cooler and see if car working after that.
But instead workshop changed EGR and Throttle Body with used genuine Toyota parts - workshop told me they found fault code for throttle body that I never saw before. Workshop also told me did not have time to clean EGR cooler but said we should clean cooler when car serviced next.
Car seemed ok after repair, but owner told me engine misbehaved a few more times - Launch then showing P0401 code 3 times, 1 showing current, 1 showing pending, 1 showing history. Cleared codes and took car to workshop to get EGR cooler cleaned - but car behaving perfect that time, workshop saying no need to clean EGR cooler.
But after that time, now one time car totally stopped on road when driving and would not start. I went to see car approx 30 mins later and car started fine with no problems (but engine warning light showing).
This time I found more fault codes
Engine:
P0401 3 times (current, pending, and history),
P3190 2 times (history and current). Launch saying P3190 Poor Engine Power, but some places on Google saying P3190 with Prius is really Throttle Body problem.
Hybrid Control:
P0A0F (current) - Launch saying Engine Failed to Start
P3000 (current) - Launch saying Battery Control System.
I cleared the codes, no warnings on dash, did small test drive and no fault codes came back.
Is there any Prius experts that can help me please?
I think P0A0F+P3000 hopefully just one time engine would not start and made hybrid system unhappy.
But looks like P0401+P3190 is the real problems.
I was hoping first maybe just EGR cooler partially blocked, and cleaning EGR cooler might fix problem.
But problem only happens rarely - if EGR cooler is blocked should problem not be getting more and more worse until cleaned?
And is P3190 really code for low engine power or code for bad throttle body? I do not have Techstream, I only have an old Launch - information I find on google giving me different information about this fault code.
Unfortunately I cleared the codes and I have zero experience with Toyota. If car sets codes in future - would it save freeze frame data that would show throttle body angle demanded and actual readings, MAF demanded and actual readings?
Hi all. Looking EWS off on M57 EDC16CP35 E83.
Decided to put this engine to my boat. If someone could do immo off.
Thats a personal project without any profit. Thank you
[color=var(--YLNNHc)]Good afternoon,
I have a Wacker Neuson WL54 wheel loader, and I'm looking for the machine's manuals and, if possible, the machine's service manuals, especially the machine's revisions.[/color]
![[Image: 20250202-185110722-i-OS.avif]](https://i.postimg.cc/Wb3B3zJg/20250202-185110722-i-OS.avif)
